Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 2 3 4 [5] 6 7 8   Go Down

Author Topic: Refurbishing an old Hohner  (Read 65018 times)

0 Members and 1 Guest are viewing this topic.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Refurbishing an old Hohner
« Reply #80 on: October 02, 2008, 10:14:58 PM »

Speaking of fine tuning, my new Hohner tools arrived this week from Sutherland Trading. Somehow they managed to miss out the most important one, a 1mm reed scraper which I'm chasing up, but I did get the spare tip I ordered which is actually long enough to use without the proper handle. Now for the mystifying bit. I expected the tip to have a burr around it, a little like a cabinet scraper, but it is perfectly smooth and doesn't scratch anything! The tip is hollow too, like a tube, which surprised me; so how do I create the cutting burr? THEO! HELP!  ???

It sounds as if the the thing you have is the handle.  The tip is only about 10 or 15 mm long - you would have difficulty holding that.  The hollow end is where you place the cutting tip.  The tip is a plain cylinder 1mm in diameter, it should be ground flat at 90º to the axis of the cylinder, giving you a sharp right angle edge all round.  It needs regular sharpening.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

waltzman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 943
Re: Refurbishing an old Hohner
« Reply #81 on: October 03, 2008, 02:47:12 PM »

It's easy to make a reed scratcher by grinding the tip of a needle file flat and sharpening on an oilstone.
Logged

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Refurbishing an old Hohner
« Reply #82 on: October 05, 2008, 11:42:34 PM »

It sounds as if the the thing you have is the handle.  The tip is only about 10 or 15 mm long - you would have difficulty holding that.  The hollow end is where you place the cutting tip.  The tip is a plain cylinder 1mm in diameter, it should be ground flat at 90º to the axis of the cylinder, giving you a sharp right angle edge all round.  It needs regular sharpening.

As always you are of course correct Theo. I ordered a 'reed scraper' for around £25 or so and a 'reed scraper replacement part' for £6-7. Well, call me dumb if you like, but I thought I was buying a complete tool for £25 and a replacement tip for an extra few pounds. Now it seems that the £25 or so is for the cutting tip and the odd few quid is for a handle. One is actually useless without the other and I have to say I'm not to impressed with the way that Hohner presents this. There are no photographs to illustrate the items that are offered for sale. I can appreciate the language barrier but in an international marketplace it would perhaps be more helpful to offer pictures of the items offered for sale so that potential customers realise just what it is they are buying?
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Refurbishing an old Hohner
« Reply #83 on: October 06, 2008, 12:03:15 AM »

£25 for the cutting tip sounds excessive, I think that must be for the handle/holder.  I think you could find something else to use as a cutting tip.  1mm tool steel?  You might need to harden it.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Refurbishing an old Hohner
« Reply #84 on: October 08, 2008, 06:10:23 PM »

£25 for the cutting tip sounds excessive, I think that must be for the handle/holder.
I already have the handle, as confirmed by Sutherlands. The handle, two reed lifters and two types of reed support tool cost the princely sum of £14.99; apparently the big bucks are for the hardened (presumably carbide or tungsten) tip!

Tuning has now started in earnest. The first reed took me about 20 mins yesterday, after which I became disenchanted with filing the belly to lower the pitch of the the reed by a semitone, so out came the soldering iron to weight the tips. This lunchtime I tuned three full plates (six reeds) in a little under half an hour which is much better progress. Two buttons tuned, only 19 more to go.  ::)
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Refurbishing an old Hohner
« Reply #85 on: October 19, 2008, 09:49:05 AM »

I now have five buttons tuned and one of the plates from the sixth. Events have overtaken me this week preventing me from achieving my goal of at least one button a day (Mon - Fri), hopefully the coming week will be a little quieter and more 'normal' - whatever that is.

I've ordered a couple of spare tips for the soldering iron as the one I'm using at the moment is going to be too big for the smaller reeds when I get to the top end.

A reed I tuned on Friday was 'one of those', I just couldn't get it right. I had to solder it three times in the end; first too much solder so it's way flat -*file,file,file*-, getting close now, -*file*- sod it, now it's sharp!  >:(  *Repeat*  >:(. Third time around I got it right but I was glad to see the back of that one I can tell you.
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Refurbishing an old Hohner
« Reply #86 on: November 05, 2008, 07:47:17 PM »

At long last the B row is tuned and ready for re-valving. I haven't decided yet whether I'll wax them back on the blocks or use gasket and screws; the latter is favourite at the moment because I can't seem to get the hang of using a reed lifter so if the reeds are waxed in I'll struggle with the final tuning.

I wouldn't mind so much if I hadn't been watching over Theo's shoulder while he deftly flicked out the inner reeds. He did this several times and it looked fairly straightforward, if a little fiddly, but try as I might I can't get it to work. All I do is get the tool jammed and risk damaging the reed.

Next time I go up there I'm going to take the video camera and film him at work to remind myself of how things are done!

In the meantime work will commence on tuning the C row.  ::)
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Refurbishing an old Hohner
« Reply #87 on: November 07, 2008, 09:15:39 PM »

At this rate the box might be finished by September/October.  ::)

At the time I thought this was an impossibly pessimistic view. We're now well into November and I'm a long way from finished!

So Grasshopper, you want to learn to fix accordion? Tell me, what is the sound of one jackal laughing?  ;D
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Refurbishing an old Hohner
« Reply #88 on: November 08, 2008, 01:48:14 PM »

£25 for the cutting tip sounds excessive, I think that must be for the handle/holder.
I already have the handle, as confirmed by Sutherlands. The handle, two reed lifters and two types of reed support tool cost the princely sum of £14.99; apparently the big bucks are for the hardened (presumably carbide or tungsten) tip!

Prompted by this sorry tale I've found what seems to be an excellent substitute for the Hohner scratcher tips.  The shank of a 1mm twist drill in 5% cobalt HSS from Axminster Tools. Cost about £1 each, and the shank is long enough to break off a piece for the scratcher and still leave a useable drill bit.  HSS is designed to remain hard even when red hot, so I may be able to speed up the tuning work!
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Refurbishing an old Hohner
« Reply #89 on: November 08, 2008, 07:11:09 PM »

Fascinating stuff Theo. I know if I put a twist drill in a vice and give it a sharp tap it will snap off but how do you then grind the broken stump flat and square?

Pete.
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Refurbishing an old Hohner
« Reply #90 on: November 08, 2008, 09:59:38 PM »

Fascinating stuff Theo. I know if I put a twist drill in a vice and give it a sharp tap it will snap off but how do you then grind the broken stump flat and square?

Pete.

With the same tool that you would need to use regularly to keep the Hohner bit sharp.  You could use a grinding wheel, but I've discovered that a diamond file does a much better job and it saves me having to stand up and go next door to the grinder.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Refurbishing an old Hohner
« Reply #91 on: November 12, 2008, 10:47:54 PM »

Looks like I'll be shopping at Axminster again in the near future, ho-hum.  ::)

As I'd already stripped off the all of the reeds from two of the three reed blocks I decided to press on with the tuning and I've now tuned all of the 4 cent flat reeds for the C row so that I can refit two whole blocks rather than one and a half. That leaves just 40 of the 126 treble reeds left to tune.  ;D

Looking at the narrow strip of wood between the apertures for the reed plates I've more or less decided to wax them back on rather than risk splitting the blocks. If I can't then get the knack of using the reed lifter to access the inner reeds for fine tuning it looks like I'll be dropping it in at Theo's sometime next year to get it finished off.  ???
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Refurbishing an old Hohner
« Reply #92 on: November 22, 2008, 03:35:50 PM »

Two full blocks of reeds are now waxed back in place. Following a suggestion by Shy Talk I've only fitted valves to the backs of the plates (draw reeds), this will allow me to fine tune the push reeds without the valves complicating things and/or getting damaged in the process. Once they are done I can fit the remaining valves and fine tune the draw reeds.

Bruce also suggested that if I'm struggling to use the reed lifter to get at the inner reeds for fine tuning (which I am),  I should go in through the port at the bottom of the block and gently push the reed tongue through to the front then slip the reed lifter behind it to keep it there. It made sense to me so that's what I'll try when the time comes.

I'll press on now and get the final two rows of plates for the C row tuned up.  :)
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

waltzman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 943
Re: Refurbishing an old Hohner
« Reply #93 on: November 22, 2008, 05:05:27 PM »

Looks like I'll be shopping at Axminster again in the near future, ho-hum.  ::)

I've now tuned all of the 4 cent flat reeds for the C row

I thought a double set of reeds was tuned on pitch for one set and slightly ABOVE pitch for the second set.  Am I missing something here?

If your valve lifter is giving you trouble It may not be the right size.  You can make a valve lifter out of an unwound guitar G string.  Bend it to the size curve you want and attatch to a wood handle.
Logged

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Refurbishing an old Hohner
« Reply #94 on: November 22, 2008, 05:26:18 PM »

I thought a double set of reeds was tuned on pitch for one set and slightly ABOVE pitch for the second set.  Am I missing something here?
This is an old pre-Corso and it's a three voice MMM so there's one reed tuned top dead centre, one fairly sharp (+10 cents) and a third one slightly flat (-4 cents). Originally the tremolo would have been more pronounced.

The reed lifter is from Hohner and it's pretty fine, I just can't seem to get the knack of using it!

Pete.
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Refurbishing an old Hohner
« Reply #95 on: November 23, 2008, 09:03:38 AM »

I've found what seems to be an excellent substitute for the Hohner scratcher tips.  The shank of a 1mm twist drill in 5% cobalt HSS from Axminster Tools. Cost about £1 each, and the shank is long enough to break off a piece for the scratcher and still leave a useable drill bit.  HSS is designed to remain hard even when red hot, so I may be able to speed up the tuning work!

As an experiment I tried this with a tungsten bit and it works fine, I will get a couple of the cobalt ones though. I was so pleased with the result that I took a short length of 4mm brass rod into work and drilled it on the lathe with a 1.5mm bit, so now I have two sizes of reed scratcher.  ;D
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Refurbishing an old Hohner
« Reply #96 on: November 24, 2008, 10:22:44 PM »

I wasn't in the mood for stripping the reed plates from the last block today so I set too with fine tuning the first row and was surprised by my progress, more than half of the reeds tuned in about forty minutes. All but one were slightly sharp which is easier to deal with than slightly flat notes when the plates are in place, particularly with the inside reeds.

Feeling pleased with self.  :)
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Refurbishing an old Hohner
« Reply #97 on: November 27, 2008, 11:21:30 PM »

Finished off fine tuning the B row and I've now tuned eight of the remaining twenty plates for the C row; when I've finished that row they will be ready to be re-valved and waxed back in, then fine tuned. The bass still has to be fine tuned too but a couple of chord buttons are making "you're an idiot and missed me entirely" discords -  so I might be digging one or two plates back out.  ::)

I'm pretty hopeful that the bulk of the work will be finished before Christmas with a bit of luck. Now I'm desperately unhappy that fitting an adjustable bass strap will probably involve remaking the bass end cover because the existing pattern of sound holes will be badly compromised by the slot I'll have to cut for it to fit.

Sometimes I despair at my own ineptitude and lack of foresight.  :(
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Refurbishing an old Hohner
« Reply #98 on: November 29, 2008, 11:43:30 PM »

Just seven plates (fourteen reeds) left to tune now. I should finish those easily during the next week and be waxing them back in next weekend. That will leave the last forty plates on the treble side to fine tune which is fairly quick to do if I haven't done any howlers; The bass end is still to fine tune and there's one obvious mistake to rectify (a chord that is truly awful so I've probably missed a reed entirely and it's one of the inside ones.  ::))

So I'm getting perilously close to actually finishing this mammoth project and it's been quite a journey. I've learned a lot, certainly enough to realise that there were many things I should have done differently. I fear I won't really learn much from some of my mistakes other than to swear I'll never undertake such a thing again!

When the whole task is finally finished I'll make a 'post mortem' summary of my experiences and do my best to explain why no sane human being would do what I've done in the way that I've done it!
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Refurbishing an old Hohner
« Reply #99 on: April 24, 2009, 11:19:33 PM »

Well I've been pretty silent about this project for some time. To be honest I became pretty disheartened and decided to take time out for a while, For a start off I don't have a workshop and prefer to work outdoors so the winter months are pretty off-putting to be honest. I also came to the conclusion that my decision to change the box from C/C# to B/C was flawed. It works for the treble end but the changes to the bass and chord reeds are too drastic, replacement reeds are needed for this to work properly.

That said I decided to move things along this week and I've now waxed in the last set of reeds on the C row. They still need to be fine tuned and have new valves fitted to the push notes but so far the results are pretty good.

Don't ask me about the bass notes though, and the chords are just a nightmare!

Pete.
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)
Pages: 1 2 3 4 [5] 6 7 8   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal