Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 2 3 4 5 6 [7] 8   Go Down

Author Topic: Refurbishing an old Hohner  (Read 64992 times)

0 Members and 1 Guest are viewing this topic.

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Refurbishing an old Hohner
« Reply #120 on: November 06, 2009, 06:52:46 PM »

I've looked at Dirk's tuner several times but I can't do the tuning in the same room as the computer and I don't have a laptop. As an amateur I can't justify the expense of kitting myself out with that kind of gear to tune a box every so often. I tune concertinas as well and I recall reading somewhere that Dirk's tuner isn't too good for those.

The later Club III, such as the Club IIIM have a complicated mechanism which shares reeds between different chords, so for example the fifth of C/G (G/D)  becomes the third of Eb/Bb, and the tonic of C/G becomes the fifth of F/C.  Quite ingenious, but it it does rule out de-clubbing the chords.

Yes, I've since discovered that this is the case with the IIIB that I'm working on, so no blocking off the thirds or tuning them flat to sweeten the chords up. Bummer.  :'(
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Refurbishing an old Hohner
« Reply #121 on: July 27, 2011, 07:24:55 PM »

I allowed myself to be distracted by a number of other things and only got as far as tuning a couple of the chord reeds before putting the old C/F Club 111 box in a corner for 18 months. It's now back out in the daylight and the basses and chords are all tuned, re-valved and back in the box, it's sounding quite good (on the bass end at least). I started on the treble end today, not difficult but pretty tedious.

I had no choice with the chords, they had to remain in Club tuning because of the reed sharing, but I'm wondering what to do about the gleichton. I find it cumbersome and really rather odd but the system does have its devotees so perhaps I should explore it more fully rather than just give up on it. In that case I'd rather have an extra three plates with C/D reeds in that I can swap about while I have a go at the Club tuning. Does anyone have three C4/D4 Hohner reed plates they would be willing to sell?
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Refurbishing an old Hohner
« Reply #122 on: July 28, 2011, 12:07:13 AM »

Does anyone have three C4/D4 Hohner reed plates they would be willing to sell?
A bit like rocking horse s**t, I would guess.
Your other option would be to try to get hold of three C#/C# reeds from a scrap accordion. You can tune one reed a semitone down to C and the other up to D. A semitone shift on each of them is not as drastic and scary as trying to tune the gleichton reeds from C/C to C/D.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Refurbishing an old Hohner
« Reply #123 on: July 28, 2011, 12:47:16 AM »

Your other option would be to try to get hold of three C#/C# reeds from a scrap accordion. You can tune one reed a semitone down to C and the other up to D. A semitone shift on each of them is not as drastic and scary as trying to tune the gleichton reeds from C/C to C/D.
My other thought was to find three D/D reeds and get the soldering iron out ...  ;D
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

waltzman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 943
Re: Refurbishing an old Hohner
« Reply #124 on: July 28, 2011, 01:52:33 AM »

I have de-clubbed two accordions now without any problems by tuning the C reeds up a whole tone.  I used a conical dremel tool and removed a little 'dimple' of metal at the tip of the reed without involving the profile of the reed at the tip or sides.  It worked well and seems very controllable to me and did not result in any funny harmonics that I could detect.  So it can be done......

Michael
Logged

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Refurbishing an old Hohner
« Reply #125 on: July 28, 2011, 05:32:19 AM »

Does anyone have three C4/D4 Hohner reed plates they would be willing to sell?
A bit like rocking horse s**t, I would guess.
Your other option would be to try to get hold of three C#/C# reeds from a scrap accordion. You can tune one reed a semitone down to C and the other up to D. A semitone shift on each of them is not as drastic and scary as trying to tune the gleichton reeds from C/C to C/D.

That's what I did with my Club II, though of course I only needed to find 2 reeds; and of course, as it's in Bb/Eb I used B reeds.
« Last Edit: July 28, 2011, 05:36:19 AM by GPS »
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Refurbishing an old Hohner
« Reply #126 on: July 29, 2011, 06:04:32 PM »

Only six more reed plates to go and the C row tuning will be finished. Currently rooting through a pile of old PA reeds looking for the C# or D plates. I have to say I don't relish taking a power tool to the reeds so if I don't find the extra plates I need it will remain a Club box at least for the time being.

No more tuning now, it's Friday evening!  :|glug
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Refurbishing an old Hohner
« Reply #127 on: July 29, 2011, 06:24:35 PM »

I agree about not wanting to rake a power tool to the reeds.  I much prefer to use a nice sharp good quality file.  Much more controllable. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Martyn

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 455
  • Hohnerohner
    • Martyn White Melodeon Tuning and Repairs
Re: Refurbishing an old Hohner
« Reply #128 on: July 29, 2011, 10:36:01 PM »

I agree about not wanting to rake a power tool to the reeds.  I much prefer to use a nice sharp good quality file.  Much more controllable. 

Or a garden tool for that matter  >:E
Logged
'Anything from a small repair to a full restoration'.
www.melodeonrepairs.co.uk

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Refurbishing an old Hohner
« Reply #129 on: July 29, 2011, 11:24:57 PM »

Or a garden tool for that matter  >:E

Arf, arf  ;)
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Refurbishing an old Hohner
« Reply #130 on: July 29, 2011, 11:30:52 PM »

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Refurbishing an old Hohner
« Reply #131 on: July 30, 2011, 12:39:28 PM »

The C row is now fully tuned and sounding good! In my rummaging around I found two D5 plates and 2 C#5 plates from a PA. Not sure if they'll match the apertures in the blocks but I'll check that out on Monday when I get a chance to look at the box again. I took some pics earlier and I'll try to put them up later this afternoon.
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Refurbishing an old Hohner
« Reply #132 on: July 30, 2011, 01:50:43 PM »

It's a bit red and erm, celluloid!


       
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Refurbishing an old Hohner
« Reply #133 on: July 31, 2011, 08:05:59 PM »

Joy of joys, my rummaging through various boxes of bits has yielded six D5/D5 six C#5/C#5 and six E5/E5 reed plates so I reckon I have enough to de-club the treble end of the box and retain the original C5/C5 plates provided the plates physically fit the Hohner blocks and allow the reeds to sound, the (Italian) reed plates are a tad longer, perhaps as much a 3mm. Fingers crossed!  :|glug
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Martyn

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 455
  • Hohnerohner
    • Martyn White Melodeon Tuning and Repairs
Re: Refurbishing an old Hohner
« Reply #134 on: July 31, 2011, 08:32:11 PM »

Joy of joys, my rummaging through various boxes of bits has yielded six D5/D5 six C#5/C#5 and six E5/E5 reed plates so I reckon I have enough to de-club the treble end of the box and retain the original C5/C5 plates provided the plates physically fit the Hohner blocks and allow the reeds to sound, the (Italian) reed plates are a tad longer, perhaps as much a 3mm. Fingers crossed!  :|glug

Hi Pete,

Please forgive me if I've misunderstood something or I have read something wrong (which is more than likely) but personally I would never mix German and Italian reeds unless it was for a seldom used accidental and even then it would be a last resort.

Martyn
Logged
'Anything from a small repair to a full restoration'.
www.melodeonrepairs.co.uk

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Refurbishing an old Hohner
« Reply #135 on: July 31, 2011, 11:19:02 PM »

Hi Pete,

Please forgive me if I've misunderstood something or I have read something wrong (which is more than likely) but personally I would never mix German and Italian reeds unless it was for a seldom used accidental and even then it would be a last resort.

Martyn

Hi Martyn,

You've not misunderstood anything or read anything wrong. I own both German made Hohners and Italian boxes and mixing the reeds from one to another wouldn't be my first choice but needs must as it were. A few PA reeds may suffer in the long run but I'll do my best to preserve the integrity of all parts involved in my experiments. The Hohner reeds will remain as they are apart from being re-tuned from A=435 to A=440, I hope that doesn't offend?

If you would like to donate a set of three Hohner C5/D5 reeds to the project they would be most welcome and may even buy you several strong beer tokens at a festival of your choice ...
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Martyn

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 455
  • Hohnerohner
    • Martyn White Melodeon Tuning and Repairs
Re: Refurbishing an old Hohner
« Reply #136 on: August 01, 2011, 12:05:22 AM »

Hi Pete,

Please forgive me if I've misunderstood something or I have read something wrong (which is more than likely) but personally I would never mix German and Italian reeds unless it was for a seldom used accidental and even then it would be a last resort.

Martyn

Hi Martyn,

You've not misunderstood anything or read anything wrong. I own both German made Hohners and Italian boxes and mixing the reeds from one to another wouldn't be my first choice but needs must as it were. A few PA reeds may suffer in the long run but I'll do my best to preserve the integrity of all parts involved in my experiments. The Hohner reeds will remain as they are apart from being re-tuned from A=435 to A=440, I hope that doesn't offend?

If you would like to donate a set of three Hohner C5/D5 reeds to the project they would be most welcome and may even buy you several strong beer tokens at a festival of your choice ...

A thought has just come to mind. Depending on your playing style -  It would be possible to 'borrow' the Eb/C# from the accidental row, put a dab of solder on the tips to take them down to D/C, tune the C/C reed to B/C in the same way and put that in the accidental row giving a B on the push.
The tiny amount of solder used would have little or no effect on the reed response/sound.
Another option as suggested by Steve is to use  C#/C# reeds from a Hohner PA of the same period tuning one a semitone up and one a semitone down. There are several options.

Martyn
www.melodeonrepairs.co.uk
Logged
'Anything from a small repair to a full restoration'.
www.melodeonrepairs.co.uk

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Refurbishing an old Hohner
« Reply #137 on: August 02, 2011, 07:10:57 PM »

Interesting suggestions there Martyn, I'll bear those in mind for further investigation but at the moment I'm going to use the Italian plates I have just to get the box playing. I'm almost half way through tuning the F row now and two of the gleichton plates have been tuned, re-valved and put away. They have been replaced using the PA D5 plates with one tongue on each tuned down to C with solder on the tips. I'm getting quite excited, I may have the whole thing finished in a week or so.  :||:
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Refurbishing an old Hohner
« Reply #138 on: August 03, 2011, 07:29:10 PM »

I'm going great guns now and well into the third set of F row reeds, I've done the flat (-0.5 Hz) and the sharp (+3Hz) sets so this set is top dead centre. This set must have been the sharp set in A = 435 because they're almost on the button in tune at A = 440, just a slight tweak needed to get them up to scratch (geddit?)  :|glug

I might be playing it by the weekend!  ;D
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Martyn

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 455
  • Hohnerohner
    • Martyn White Melodeon Tuning and Repairs
Re: Refurbishing an old Hohner
« Reply #139 on: August 03, 2011, 09:37:00 PM »

Sounds like you are sailing through it now. I hope we are going to see a video or hear a soundclip when it's done.

Martyn
Logged
'Anything from a small repair to a full restoration'.
www.melodeonrepairs.co.uk
Pages: 1 2 3 4 5 6 [7] 8   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal