Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Pallets on single row  (Read 2122 times)

0 Members and 1 Guest are viewing this topic.

nfldbox

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 492
Pallets on single row
« on: November 03, 2010, 06:03:15 PM »

How is the pallet attached on a standard open single row? On my Bouchard the lever--or whatever you might call it--seems to be aluminum. This makes it quite easy to bend, for both good and bad. Is this the usual?
Logged
BC Cairdin
BC Hohner Double Ray
Bouchard en Ré

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Pallets on single row
« Reply #1 on: November 04, 2010, 01:56:02 PM »

I use steel levers on my Wesson Clipper and Windjammer. Very tough and resilient.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

johnners

  • Guest
Re: Pallets on single row
« Reply #2 on: November 04, 2010, 02:05:06 PM »

OK, I know they aren't open to view (therefore don't have to be pretty) but the pallet attachments on my HA114 (thanks, Rees) are steel sections embedded into a slot in the wooden pallet, then glued rigid.
Doesn't aluminium (aluminum) work harden, like bronze and copper?
Logged

Andrew Wigglesworth

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1101
  • 07
    • My website
Re: Pallets on single row
« Reply #3 on: November 04, 2010, 02:31:00 PM »

They're steel on my Zero Sette one row.

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Pallets on single row
« Reply #4 on: November 04, 2010, 03:31:00 PM »

All the ones I've seen have been attached by glue or wax in the groove in the back of the pallet.  I think it was Lester who said he'd used a hot glue gun for this - you can remove it again with heat.

Rob.
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Pallets on single row
« Reply #5 on: November 05, 2010, 06:39:39 PM »

The EATMT melodeons made under instruction from Emmanuel Pariselle use aluminium rods.
Also aluminium on Junior Martin.
Marc Savoy and Eric Martin use copper rods.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Pallets on single row
« Reply #6 on: November 05, 2010, 07:28:12 PM »

I use aluminum welding wire in 5052 alloy I believe.  Bends easily enough and holds it's shape well.  I use stainless steel axle rods.

melodeon

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1732
Re: Pallets on single row
« Reply #7 on: November 05, 2010, 08:38:23 PM »

Square cross section copper  as used in large electric motors



JJ Hildreth
Adult Prodigy
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal