Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Valve glue, again... sorry  (Read 2554 times)

0 Members and 1 Guest are viewing this topic.

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Valve glue, again... sorry
« on: November 21, 2010, 01:03:01 PM »

I was recently informed of a glue I had never heard of before, fish glue.  Kinda like liquid hide glue, only different.  In researching it, it's most common use apparently is leather, and works well on metal.  Was wondering if anyone uses it for reed valves, seems like a good match.  Also easily reversible.  Fairly quick drying, but good initial tack.  I tried it on some and immediately sounded them and couldn't get them to dislodge even before drying.

waltzman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 943
Re: Valve glue, again... sorry
« Reply #1 on: November 21, 2010, 02:30:44 PM »

I was recently informed of a glue I had never heard of before, fish glue.  Kinda like liquid hide glue, only different.  In researching it, it's most common use apparently is leather, and works well on metal.  Was wondering if anyone uses it for reed valves, seems like a good match.  Also easily reversible.  Fairly quick drying, but good initial tack.  I tried it on some and immediately sounded them and couldn't get them to dislodge even before drying.

I've never used fish glue but I've read that it is hygroscopic (unlike hide glue) and under humid conditions the joints can fail.  So it might work well in Arizona but not so well in Louisiana........

I've used contact cement (Barge) which has fairly good initial tack and sticks to wood and plastic and leather very well and as far as I know is impervious to humidity.  It is harder to clean off (for revalving) than the shellac type glues.  This problem is helped by using it on a very small area for each valve.
Logged

an bosca ceoil

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 347
Re: Valve glue, again... sorry
« Reply #2 on: November 21, 2010, 03:35:31 PM »

I doubt that fish glue, though it may well work initially, would be satisfactory in the long term.
I am pretty sure it is water reversible and would be affected by humidity.
(I think it is the stuff used, before sellotape, on paper tape which was drawn through water to make it adhesive.)
Logged

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Valve glue, again... sorry
« Reply #3 on: November 21, 2010, 03:43:07 PM »

It was also once in regular use in the theatre for attaching false facial hair. It used to stink something awful, but was easily removed with warm soapy water.
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

strad

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 418
Re: Valve glue, again... sorry
« Reply #4 on: November 21, 2010, 08:10:03 PM »

Hide glue seems to like humid conditions but it does NOT like low humidity. I had a complete lower bout on my fiddle come unglued when on tour in a hot dry situation. Fortunately I had a second fiddle with me at the time.

Nigel
Logged

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Valve glue, again... sorry
« Reply #5 on: November 24, 2010, 01:01:17 PM »

It is harder to clean off (for revalving) than the shellac type glues. 
When I get around to revalving my single row, it's clear that I'm going to have to remove some old glue. Didn't know what it was, but shellac seems possible - it's hard and dark coloured.

Is there a solvent or something to shift it, or will I just need to scrape it off?

(The valves re plastic (Mylar?) and I plan to use a contact adhesive, Bostik or Evostik, to re-attach them. )
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Andrew Culwell

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 620
Re: Valve glue, again... sorry
« Reply #6 on: November 24, 2010, 01:29:48 PM »

I've been using my Dremel tool with a circular attachment like this
http://www.amazon.com/Dremel-512E-Finishing-Abrasive-2-Pack/dp/B000FBK43M/ref=combo_pack_i_13

I've been afraid to use solvents or anything else.  It works quite well. I use a wire wheel attachment to remove old wax.  They Make a wire wheel that is made for softer white metals like zinc etc. These don't damage the reeds or frames.   This is my first attempt at reed work so take my recommendations with a grain of salt.
Logged
Hohner's, Paolo Soprani red 4 voice, Paddy Clancy Celtic

waltzman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 943
Re: Valve glue, again... sorry
« Reply #7 on: November 24, 2010, 01:33:03 PM »

It is harder to clean off (for revalving) than the shellac type glues. 
When I get around to revalving my single row, it's clear that I'm going to have to remove some old glue. Didn't know what it was, but shellac seems possible - it's hard and dark coloured.

Is there a solvent or something to shift it, or will I just need to scrape it off?

(The valves re plastic (Mylar?) and I plan to use a contact adhesive, Bostik or Evostik, to re-attach them. )

It scrapes off quite easily with a knife in my experience.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal