Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Hohner bass mechanism nails  (Read 2952 times)

0 Members and 1 Guest are viewing this topic.

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Hohner bass mechanism nails
« on: November 26, 2010, 10:17:56 PM »

What do people use to replace the nails in the Hohner Bass Mechanism? I have just had to strip one out of the 1140 I am refurbing to de-rust it and had to cut the nails to get them out.

TIA

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner bass mechanism nails
« Reply #1 on: November 26, 2010, 10:35:46 PM »

The nails that form the pivot between button rod, and pallet lever? 

I have heard some say they recycle reed nails for this, but I don't like to do that because they are a slightly smaller diameter and result in more slop and rattle in the action.  You can use something a little thicker and drill the holes out to match.

I rarely take the nails out, unless a rod is actually broken.  I remove the buttons, release the springs, undo the screws and lift out the whole action.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Hohner bass mechanism nails
« Reply #2 on: November 27, 2010, 12:11:46 AM »

I'm interested in this thread too.

I want to bush the bass buttons on a Hohner Erica to stop the rattling. To do this, I need to remove the rods (with the buttons still affixed - they are glued in place on an Erica) from the holes so I can enlarge the latter slightly and apply bushing felt.

With the springs unhooked and the action retaining screws removed, there is still insufficient clearance to remove the rods from the holes, so it needs to be a case of dismantling the bent-nail pivot and reassembling it again after the holes have been bushed. Until I can source replacement nails I am reluctant to start straightening out the bent nail to remove it, in case it breaks during the straightening or when being re-bent on reassembly.

Any advice would be welcome, thanks!
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Mike Averill

  • suffering from MAD
  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 325
Re: Hohner bass mechanism nails
« Reply #3 on: November 27, 2010, 08:51:15 AM »

piano wire, comes in a great range sizes, available in most model shops
Logged
Hohner - 1 row 4 stop C and G, pokerwork DG, DoubleRay DC#, Corso CC#, Corona III ADG, CLUB X CF, Elysium II CF
Saltarelle 1 row 4 stop D, Castagnari Giordy DG, Sander DG
Sonola CC#, Walters DC#

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Hohner bass mechanism nails
« Reply #4 on: November 27, 2010, 09:24:31 AM »

Until I can source replacement nails I am reluctant to start straightening out the bent nail to remove it, in case it breaks during the straightening or when being re-bent on reassembly.

Any advice would be welcome, thanks!

In my experience it is v difficult to straighten the nails sufficiently to extract them especially if there is surface rust etc on the mechanism (you can tell the sort of boxes I am working on  ::) ).   

Bill the Farmer

  • Not quite so
  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 497
  • Hohner Club, Liliput...
    • Bill Farmer
Re: Hohner bass mechanism nails
« Reply #5 on: November 27, 2010, 09:58:35 AM »

piano wire, comes in a great range sizes, available in most model shops

I just used ordinary thin galvanised garden wire, it's the same diameter as the nails which break if you try to straighten them.
Logged
Bill of Old Radipole Village

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Hohner bass mechanism nails
« Reply #6 on: November 27, 2010, 04:37:46 PM »

Turns out that B&Q Veneer Pins are exactly he correct size, I now have enough to refurbish about 100 melodeons  ;D

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Hohner bass mechanism nails
« Reply #7 on: November 28, 2010, 08:00:15 AM »

Turns out that B&Q Veneer Pins are exactly the correct size, I now have enough to refurbish about 100 melodeons  ;D
Brilliant - thanks for the info Lester!
What's the minimum quantity you can buy from B&Q? I only want a few - would you consider selling me a dozen or so pins? Ta!
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Hohner bass mechanism nails
« Reply #8 on: November 28, 2010, 08:13:48 AM »

Turns out that B&Q Veneer Pins are exactly the correct size, I now have enough to refurbish about 100 melodeons  ;D
Brilliant - thanks for the info Lester!
What's the minimum quantity you can buy from B&Q? I only want a few - would you consider selling me a dozen or so pins? Ta!

They come in 250g packs which is about far more than you could ever need, pm me your address and I will stick some in the post :)

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Hohner bass mechanism nails
« Reply #9 on: November 28, 2010, 08:32:53 AM »

Turns out that B&Q Veneer Pins are exactly the correct size, I now have enough to refurbish about 100 melodeons  ;D
Brilliant - thanks for the info Lester!
What's the minimum quantity you can buy from B&Q? I only want a few - would you consider selling me a dozen or so pins? Ta!

They come in 250g packs which is about far more than you could ever need, pm me your address and I will stick some in the post :)
Cheers Lester!  (:)
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal