Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Reed cleaning and rust removal  (Read 17382 times)

0 Members and 1 Guest are viewing this topic.

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Reed cleaning and rust removal
« on: December 05, 2010, 11:39:40 PM »

I can't find a description of how to clean the underside of a reed, that is, the surface that sits in the bottom of the reed plate opening or the side of the reed you tune when you use the bent wire to lift the tongue. Bent wire technique gives you access to about 1/3 of the tongue length but the rest is buried in that very narrow hole.  I'm worried about making changes to the opening in the aluminum plate. I've got a Presswood Pokerwork with "H" reeds in need of tuning and removal of some rust on both sides of the reed.

Thanks!
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Reed cleaning and rust removal
« Reply #1 on: December 06, 2010, 12:24:58 AM »

You will probably just have to accept that you will need to remove the reed plates. It's the only way to determine where all the rust lies and be able to clean it off. If you are doing a tuning job, you would be well advised to change the valves anyway, so that's another reason for the reed plates to come off.

So.....
Remove all the reed plates
Remove all old valves
Clean off any old wax (if previously used) and gunge from reedplates and reed chambers
Clean rust from reeds
Replace all valves
Rewax reed plates back into place
Tune reeds
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Andy Simpson

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 938
Re: Reed cleaning and rust removal
« Reply #2 on: December 06, 2010, 12:56:16 AM »

I concur with Steve.....or you could have yourself miniaturised a la Fantastic Voyage or that one with Dennis Quaid that I can't remember the name of and is really annoying me and I'll have to go and look it up on Wikipedia when I finish this. Just fly inside each reed chamber in a similarly miniaturised craft and clean it from the underside.

That way you won't have to remove the reedplates but the downside is that it's beyond the capability of modern science and technology and will take years of research and cost billions if it's even possible at all....you'll also have to get someone else to open and close the pallets for you so that you can get inside.
Logged

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Reed cleaning and rust removal
« Reply #3 on: December 06, 2010, 01:03:42 AM »


So.....
Remove all the reed plates
Remove all old valves
Clean off any old wax (if previously used) and gunge from reedplates and reed chambers
Clean rust from reeds
Replace all valves
Rewax reed plates back into place
Tune reeds

Hi Steve, Thanks. I'm planning to remove the plates, clean, install new valves, and rewax. I think I wasn't too clear with my question so I'll try again with a photo borrowed from Theo's page on tools.

The photo shows one reed on the top of the plate, on the left. This side of the reed is easy to get to, same thing if you turn over the reed plate to access the other reed from the riveted side.

The other reed on the right is being lifted out of the reed chamber with a pinger to access for tuning. My question is about how to remove rust from the portion of the left-hand reed that you can only get to through the reed chamber below the level of the pinger? There's quite a bit of reed surface area that can only be accessed by going through the chamber and there's lots of surface in the chamber that can be damaged in the process if I don't do it right.

I hope this is a bit clearer. Let me know if I've muddled the explanation again.

BTW, given that the existing reeds are tuned to Hohner's original A=434 (I think) I'm planning to raise the pitch to A=440. And I want to tune the instrument dry. Some of the reeds are starting at 30 cents or more flat. Don't I want to do a preliminary tuning of both reeds in the plate with valves while I have access to the "easy side" of the reed before waxing on to the blocks and fine tuning in the instrument itself? How far sharp or flat should I go to end up close to being on pitch before I install the reedblocks to start finish tuning?x foot

Andy, I'm six foot three and have yet to start the plunge into old age and a shrunken physiology, LOL. But hey, as long as you send Raquel Welch along with me, I'm fine! The movie you're looking for is "Fantastic Voyage" in which Ms. Welch plays a role.

Thanks,

Ed
« Last Edit: December 06, 2010, 01:06:50 AM by Telemorris »
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Reed cleaning and rust removal
« Reply #4 on: December 06, 2010, 01:20:20 AM »

Ed,

You can clean rust off the undersurface of the reed tongue using a fibreglass pen, designed for cleaning printed circuit boards. See here:
Fibreglass pen
Take care though, as you will generate some fine glass-rich dust in the process; wear a dust mask, gloves and eye protection.
Also, just a quick correction on terminology: the reed chamber is the hollow wooden structure which the reed plates are waxed on to. The slot in the aluminium reed plate is called 'the slot'. The fibreglass pen should enable you to clean the reed tongues without damaging the slot sides.

As to raising the pitch from A=434 to 440, I've never sharpened reeds by that amount before, so others are better qualified to advise. But my feeling is nevertheless to wax the reeds in place and then tune. Don't attempt to 'rough-tune' first. Raising the pitch by 30 cents or so doesn't need that much metal to be removed from the reed tip, and by 'rough tuning' off the reed block, you could risk going too far too easily.

Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Reed cleaning and rust removal
« Reply #5 on: December 06, 2010, 02:05:46 AM »


Take care though, as you will generate some fine glass-rich dust in the process; wear a dust mask, gloves and eye protection.
Also, just a quick correction on terminology: the reed chamber is the hollow wooden structure which the reed plates are waxed on to. The slot in the aluminium reed plate is called 'the slot'. The fibreglass pen should enable you to clean the reed tongues without damaging the slot sides.

Thanks Steve,

I'm aware of the fiberglass pens and somewhat reticent to try them because of the glass particles. I've done plenty of work with fibreglass insulation over the years with the resultant itchy eyes, hands, and lungs. Sounds like I need to assess the extent of the rust on the reed I access through the slot. If it's not bad, don't do anything. If there's a lot of rust, find a way to scrape some off with a brass stick or fiberglass pencil and keep the air flow going at all times.

Thanks,

Ed
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: Reed cleaning and rust removal
« Reply #6 on: December 06, 2010, 02:07:39 AM »

If you use your shim and slide it under the reed from the underside then you can scrape off a bit more of the rust. Obviously this needs to be done with extreme care and incredibly lightly, or you will score the underside of the reed which will lower the pitch. It still won't affect the area closest to the rivet though.
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Reed cleaning and rust removal
« Reply #7 on: December 06, 2010, 04:03:38 AM »

I guess the "rough" tuning would depend on equipment. For going more than 10 cents, I like to tune the reed in a tuning bellows similar to this one http://www.youtube.com/watch?v=U--Vf99jyTA .  It gets me close very conveniently, I then install the reed, wax, and fine tune.

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Reed cleaning and rust removal
« Reply #8 on: December 06, 2010, 04:17:43 AM »

I guess the "rough" tuning would depend on equipment. For going more than 10 cents, I like to tune the reed in a tuning bellows similar to this one http://www.youtube.com/watch?v=U--Vf99jyTA .  It gets me close very conveniently, I then install the reed, wax, and fine tune.

I've been looking at that video for awhile and like it.

How close do you get to the actual pitch? Do you tune above the nominal pitch expecting it to fall one the reed is in the instrument or do you expect the pitch to sharpen once the reed is waxed and in the instrument?
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Reed cleaning and rust removal
« Reply #9 on: December 06, 2010, 07:52:58 AM »

I'm aware of the fiberglass pens and somewhat reticent to try them because of the glass particles. I've done plenty of work with fibreglass insulation over the years with the resultant itchy eyes, hands, and lungs. Sounds like I need to assess the extent of the rust on the reed I access through the slot. If it's not bad, don't do anything. If there's a lot of rust, find a way to scrape some off with a brass stick or fiberglass pencil and keep the air flow going at all times.
You can also make your own tools to remove rust, using lolly sticks (these things) and narrow strips of fine (400 - 600 grade) carborundum paper.  
Sand one rounded end of the lolly stick to get a good clean perpendicular edge. Cut a narrow strip of carborundum paper the same width as the lolly stick edge and just long enough to go round the semi-circular ends. Glue the carborundum strip to the edge of the lolly stick at the rounded end, using PVA glue. Once the glue is dry you can use the tool as a very fine, gentle file to remove rust. You can poke it through the reed plate slot to clean the underneath surface of the reed without damaging the slot.

You can make a set of files like this using somewhat coarser carborundum paper for use as reed tuning files too. They are quick and easy to make and last quite a long time before wearing out. Then just remove the old carborundum strip and glue on a new one. By modifying the dimensions of your lolly stick, you can make different sizes of file to suit different size reeds.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Reed cleaning and rust removal
« Reply #10 on: December 06, 2010, 12:43:41 PM »

Telemorris, I spent some time getting it as air tight as I could, and making sure the reed is pressed down pretty solid, it will be within 5 cents when I put it in the accordion.  But it doesn't take much air passage, or if the reed is not consistently pressed down firmly, to make a much wider gap.

Rust is hard to remove on the inside of the slot, near the bottom edges.  I refurbished a very rusted accordion a while back and tried some stuff called Evapo-rust.  It seemed to work well at dissolving the rust, and I was hoping it would neutralize it from coming back.  It's been about 2 years, and hopefully next month I'll be able to inspect that accordion and see how well it has done.  One thing I learned is it leaves a film, so after I soaked the reeds in a bath of it, i gave them a quick rinse in lacquer thinner before installing the valves.

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Reed cleaning and rust removal
« Reply #11 on: December 06, 2010, 05:44:41 PM »

You can also make your own tools to remove rust, using lolly sticks...

We call them "popsicle" sticks LOL

Quote
You can make a set of files like this using somewhat coarser carborundum paper for use as reed tuning files too. They are quick and easy to make and last quite a long time before wearing out. Then just remove the old carborundum strip and glue on a new one. By modifying the dimensions of your lolly stick, you can make different sizes of file to suit different size reeds.

I've been experimenting with a piece I cut off an old saw blade with a dremel metal cutting blade. I sliced a narrow (9mm or so) slice, bent one end back a bit to make a rounded end for the sandpaper to pass around. Sandpaper strips are held with the fingers, not glued down in order to slide a new fresh section of the 220 grit wet or dry sandpaper I've been using for tuning. With the tuning I've done so far this tool setup works very well. I can use one end flat for sanding a broad area of the reed and the curved section for a more focused removal that still blends the strokes of the tool. I like it quite a bit since it's thin and can get under a valve easily. Will post a photo a bit later (sick in bed the last two days, grr).

I've been thinking I could take another couple of slices of steel and grind the width to about the thickness of a lolly, maybe even make a couple different widths depending on the width of the reed.

BTW, is 220 too coarse for tuning? I've looked at some of the file marks on the reeds and the 220 seems to leave somewhat finer scratches.

Ed
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Reed cleaning and rust removal
« Reply #12 on: February 28, 2011, 05:24:53 PM »

Thanks to Theo and Lester's pointers on cleaning rust with a PCB cleaning block (and Lester's supply of same block - thanks!), I now have nicely clean reeds and reed plates in my G/C Presswood Pokerwork! Even the undersides of the tongues are clean though it's a tedious process to do so.

It was very informative to look at the undersides of the reed tongues under strong light and realize just how much gunk (dirt, dust, grease, and even fingerprints!) was attached to the reed tongue in addition to rust. The fingerprints are evidence that the Hohner reeds were not clean at installation and the grease attracted bits of fine dirt over the next 50 to 60 years.

I started by removing large bits of rust bloom with a small piece of brass with a blunt end that just fit into the chamber. The brass was able to scrape off the rust particles without scratching the steel. Cleaning the underside of each tongue involved gently rubbing back and forth over the tongue surface with a thin slice of the cleaning block that would just fit into the reed chamber. Inserting a toothpick into the reed chamber to lift the tip of the reed tongue makes work on the tip much easier (similar to using a reed lifter to raise the tongue for tuning). It's good for cleaning the walls of the chamber too if there's oxidation bloom on them as well.

That this treatment did not damage the reeds is evidenced by the fact that the bluing was largely untouched except where the blocking piece rubbed for too long. There are no scratches or other damage that I can find from cleaning the reeds this way. The tops of the reeds were treated in the same way. The reeds are now valved and waxed into the blocks, waiting for a tuning.  

One observation I made is that the underside of these Hohner reeds were decidedly more rusty than the top surfaces. I suspect it has to do with taking a cold instrument into a warm damp room and condensation forming on the reeds. Unless an instrument is played soon after condensation has formed, a humid environment develops inside each reed chamber and the chamber and leather valves become saturated with moisture. Air flow through each chamber is the only way to bring the metal to room temperature and dry out the valves and tongue.

Ed
« Last Edit: February 28, 2011, 06:51:25 PM by Telemorris »
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Reed cleaning and rust removal
« Reply #13 on: February 28, 2011, 10:03:09 PM »

One thing I've used on a badly rusty set of old Hohner reeds was Evapo-rust, link below.  I removed the reed plates and valves, cleaned off the wax, and soaked them in this stuff for a while, then a quick rinse in lacquer thinner.  Removed the rust, and now a year and a half later the rust has not returned.  I was pretty impressed.  I did the lacquer thinner because I learned that the Evaporust leaves a sticky film if allowed to dry with out rinsing off.

http://www.amazon.com/Evapo-Rust-Rust-Remover-1-Qt/dp/B001BNZGY0

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: Reed cleaning and rust removal
« Reply #14 on: March 01, 2011, 01:48:12 AM »

Telemorris, I did the same thing with my 1140, except that there was mercifully little rust on the underside for some reason. That which there was I removed with a bit of brass as you said. The PCB block is a fantastic little thing.
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Reed cleaning and rust removal
« Reply #15 on: March 01, 2011, 07:48:10 AM »

Glad it went well :)
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal