Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Cleaning and setup of button mechanisms.  (Read 2712 times)

0 Members and 1 Guest are viewing this topic.

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Cleaning and setup of button mechanisms.
« on: December 07, 2010, 10:43:49 PM »

I've noticed that some of the buttons on my Erica and Presswood squeak or give a metallic scraping sound when the key is depressed. Another issue is that the buttons are not all the same height above the keyboard. Some of the metal key brackets need some judicious bending, probably at the right angle joint where the spring is attached.

Is it a good or bad idea to use a small bit of light machine oil on the moving parts of the keys?

Any ideas about how to go about making small bends in the keys to set the height of the buttons to be all the same. I'll wait to do this until the pallets are refaced, yes. I do know that at least one button is 1/8" or more above the general level of all the other button tops.

Ed
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Cleaning and setup of button mechanisms.
« Reply #1 on: December 07, 2010, 10:53:23 PM »

To quote Theo from a previous thread on squeaking (Forum Search is your Friend   ;D  )

Definitely no oil!  

To deal with unwanted noise first you have to identify the exact source of the noise, only then can you decide how to tackle it.  It may be something that needs to be re-aligned, or cleaned.


You may well find the squeaking is from the button rubbing where it passes through the fingerboard and it will just be a matter of some slight alignment adjustment on the button.

Definitely wait until you have refaced the pallets and then a little gentle and judicious bending of levers will sort out your button height. I assume you will also be restricting the button travel as per Theo's excellent tutorial (your chance to use search  ::) )
« Last Edit: December 07, 2010, 10:54:57 PM by Lester »
Logged

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Cleaning and setup of button mechanisms.
« Reply #2 on: December 07, 2010, 11:02:51 PM »

To quote Theo from a previous thread on squeaking (Forum Search is your Friend   ;D  )

Definitely no oil!  

To deal with unwanted noise first you have to identify the exact source of the noise, only then can you decide how to tackle it.  It may be something that needs to be re-aligned, or cleaned.


You may well find the squeaking is from the button rubbing where it passes through the fingerboard and it will just be a matter of some slight alignment adjustment on the button.

Definitely wait until you have refaced the pallets and then a little gentle and judicious bending of levers will sort out your button height. I assume you will also be restricting the button travel as per Theo's excellent tutorial (your chance to use search  ::) )

Thanks Lester. I've already installed a button travel restriction bar on the Presswood though I'm still working on adjusting the bottom height of the button for the two rows. Each row of buttons hits the bar in a different way. I've already thrown away one attempt and my do so again with the second attempt. I'l eventually get it right. I come from having been a luthier. My frame of reference is setting up a guitar action, a very finicky process so I've all the patience I need for this task. Not sure the buttons need to be perfectly equal in their heights relative to each other though the more exact I can get the heights, the easier the instrument will be to play. That's my goal.

Ed
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Cleaning and setup of button mechanisms.
« Reply #3 on: December 07, 2010, 11:10:39 PM »

If you are concerned that there is resistance to movement from the axle rod, or if it has a build-up of crud then its worth stripping the whole mechanism.  Three tips:  1 release all the springs before removing the holding screws, 2 - screw the action down to a board before starting to pull the axle rod, 3 - have a length of stiff wire handy to thread in from the opposite end as you remove the rod. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Cleaning and setup of button mechanisms.
« Reply #4 on: December 07, 2010, 11:29:58 PM »

3 - have a length of stiff wire handy to thread in from the opposite end as you remove the rod.  

Thanks for that bit of advice Theo!  I did have visions of all those small parts coming undone, waiting to argue with me when my fat fingers can't get them in place when I put it all back together. Thank you, thank you.

Another question for the skilled players of two row melodeons: What's the ideal height of the buttons above the keyboard? The keys do need to travel a certain amount to pull the pallet away from the soundboard and allow a sufficient flow of air, true, but more than necessary and you're slowed down by the distance the button travels.

Added later: Directly related to this, and probably the best place to start the chain of adjustments that ends with button height and button travel, is the distance of the pallet from the soundboard (fondo?) that allows air to flow in or out. What's the minimum distance necessary between the pallet surface and the soundboard? My two instruments have varying distances and I'd like to try equalizing the distances when I get to that part of the repair.

Thanks
« Last Edit: December 08, 2010, 12:58:35 AM by Telemorris »
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Cleaning and setup of button mechanisms.
« Reply #5 on: December 08, 2010, 07:55:20 AM »

I can't give you a measurement, but its much less than you think! 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Cleaning and setup of button mechanisms.
« Reply #6 on: December 08, 2010, 08:35:20 AM »

Building in Theo's advice, stripping down the mechanism is well worthwhile if it is rusty as it will definitely free it up. As I am fairly new to all this I take a few close up photos of anything I intend to take apart so I can refer to them when it wont go back together.

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Cleaning and setup of button mechanisms.
« Reply #7 on: December 08, 2010, 08:37:11 AM »

I agree with Theo - the necessary clearance of the pallets off the tone holes needed to give a full volume sound and with no effect on the tuning, is actually quite small. Again I can't quote exact figures but a few millimetres is usually sufficient. It will probably vary from one instrument to another, so it is worth experimenting: on an unmodified instrument, just try pressing the buttons down slowly a little at a time whilst using normal bellows pressure.  You should soon be able to see/hear what the minimum required clearance is.

As to button height on the keyboard, I have modified my Hohner Erica to limit the button travel. When fully depressed, the top of the button is just (about 1 mm) below the surface of the keyboard. Even with this limiting modification, the pallets open more than enough to give the correct intonation and a good volume.  
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

LJC

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 527
Re: Cleaning and setup of button mechanisms.
« Reply #8 on: December 08, 2010, 08:47:30 AM »

I've found getting the little brass screws back into place when re fitting the mechanism can be a pain - a pair of tweezers from my first aid kit, designed for removing ticks (!), is just the right shape and size to hold them in the right way to fit them back in easily.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Cleaning and setup of button mechanisms.
« Reply #9 on: December 08, 2010, 08:49:22 AM »

Yes they are in pain!  I apply a spot of reed wax to the tip of the screwdriver, then the screw will stick to the screwdriver!
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Cleaning and setup of button mechanisms.
« Reply #10 on: December 08, 2010, 12:37:18 PM »

Another useful tool for connecting and disconnecting springs is a suitable size of crochet hook.  Without it the finger tips get very sore by the time you've disassembled and re-assembled a Hohner keyboard.  Also a small screwdriver with a notch in the centre of the blade, to hold the wire whilst you poke it back into place.  I, too have an old bread board with suitable mounting holes for each of my boxes' actions.  Once suitably equipped, jobs like changing a treble spring can really be simple.

Rob.
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Cleaning and setup of button mechanisms.
« Reply #11 on: December 08, 2010, 12:41:04 PM »

Yes they are in pain!  I apply a spot of reed wax to the tip of the screwdriver, then the screw will stick to the screwdriver!

Good call Theo, I have always spent time finding my blutac to do the same job, never thought of using wax which is lying around just in front of me, more living and learning  ;D
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal