Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Reed block measurements on Hohner Club II  (Read 4859 times)

0 Members and 1 Guest are viewing this topic.

Sandy Flett

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 709
    • Accordion and Melodeon Blog
Reed block measurements on Hohner Club II
« on: December 18, 2010, 11:43:06 AM »

I am looking for a favour from an owner of a Hohner Club II [edit 20/12/10 it needs to be a Club IIB] such as in this eBay item 170578670569.

I need measurements of the hole distances in the treble reed blocks, specifically:

Over 10 holes, how many mm from the lower edge of hole 1 to the upper edge of hole 10

Over 11 holes, how many mm from the lower edge of hole 1 to the upper edge of hole 11

And can you advise exactly which model the measurements were taken from, please - eg rounded Club IIB as in eBay item, or square Club II.

Any help very much appreciated.
« Last Edit: December 20, 2010, 09:37:09 AM by Sandy Flett »
Logged
DG Dino Baffetti Carnival II (plus accordions)
Accordion and Melodeon blog

Sandy Flett

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 709
    • Accordion and Melodeon Blog
Re: Reed block measurements on Hohner Club II
« Reply #1 on: December 18, 2010, 12:40:14 PM »

I should add to the above, if your [edit 20/12/10] Club IIB has seen better days and you would not mind being shot of it, then PM or e-mail me with an idea of what you might sell it for. Needless to say, any purchase would be dependent on the measurements proving to be what I need.
« Last Edit: December 20, 2010, 09:40:59 AM by Sandy Flett »
Logged
DG Dino Baffetti Carnival II (plus accordions)
Accordion and Melodeon blog

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Reed block measurements on Hohner Club II
« Reply #2 on: December 18, 2010, 02:01:08 PM »

Sandy,

I have an old Club II (old square type) that you could have a look inside.  I'm in Basingstoke, so not a million miles away - but it's snowing at the moment, so the roads could be blocked by incompetent Xmas shoppers' cars!  Sorry for the gripe, but driving a 4x4 doesn't help get past those spinning their wheels in first gear.

I'm not absolutely sure which way is up so bottom to top confuses me!  Are any of these measurements needing me to remove reeds?  Perhaps a picture of a reed block with the required dimensions marked?

Rob. (bear of little brain)
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reed block measurements on Hohner Club II
« Reply #3 on: December 18, 2010, 04:13:16 PM »

Sandy

The vast majority of Hohners have the reed spacing at 19mm centres on the treble reed blocks. This definitely applies to pokerwork/erica and similar two row models, and Club II/Erika because I've just checked the measurements.  I'm pretty sure it also applies to the all the three voice Club III, IV etc as well.  The only exceptions are the Liliput and Preciosa.

Centre to centre spacing is a much more satisfactory way of working with hole spacings than edge to edge, because it is independent of the size of the holes, and its what you need to know if you are planning to mark out and drill holes.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Sandy Flett

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 709
    • Accordion and Melodeon Blog
Re: Reed block measurements on Hohner Club II
« Reply #4 on: December 18, 2010, 04:23:59 PM »

Theo - many thanks.

Rob - looks like Theo's answer covers your model, but many thanks for the offer to help.

Logged
DG Dino Baffetti Carnival II (plus accordions)
Accordion and Melodeon blog

Microbot

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 345
Re: Reed block measurements on Hohner Club II
« Reply #5 on: December 19, 2010, 11:08:41 AM »

Hi Sandy and Theo and others,

Someone must have one of the rounded Club IIB instruments - the ones that look like Darth Vader's helmet! They were usually red or light grey ... see Ebay item 170578670569.

It might help to put some perspective to this seemingly 'techy' thread ... Sandy and I are working on a project that would require a set of Hohner treble reeds and reedblocks to insert into another make of instrument. Sandy has done some initial experiments that sound very promising, but there was a slight mismatch in reedblock size. The reeds and reedblocks obviously need to be exactly compatible ... this means spaces of 17mm from centre hole to centre hole... as Theo says, most Hohner models are slightly wider spaced than this.

But I have one of the Club IIIM which is precisely 17mm centre hole to centre of the next hole... just right! ... the drawback is its in mint condition so cannot be 'raided', and also has coupler slides in which are not required. The Club IIB as in eBay item 170578670569 has the same casing and action as my Club IIIM, so we think it also will have 17 mm spacings. It also has no registers... it should be perfect for the job.

So any help would be appreciated - as I say - Someone must have one of the rounded Club IIB instruments - the ones that look like Darth Vader's helmet!

cheers

Mike
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reed block measurements on Hohner Club II
« Reply #6 on: December 19, 2010, 12:46:08 PM »

The Club IIB as in eBay item 170578670569 has the same casing and action as my Club IIIM, so we think it also will have 17 mm spacings.

Mike, when you say "the same....action"  have you seen a view under the grill showing the pallets?

If there are two rows of pallets (as in the IIIM) then the half row reeds are sharing the main blocks and must be 17mm centres to fit all the reeds in.  If there are three rows of pallets then they will probably be 19mm spacing.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Microbot

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 345
Re: Reed block measurements on Hohner Club II
« Reply #7 on: December 19, 2010, 02:19:28 PM »

A Good point Theo

- a view of the pallets would indeed reveal the reedblock arrangement, which would then suggest the spacings... as Im sure you know the Club IIIM is arranged with 3 reedblocks (the accidentals contained along the main reedblocks) and therefore my/our hope is that the Club IIB is similar with just 2 reedblocks. But the ClubIIB may have separate reedblocks for the accidentals and therefore reedblocks with the conventional wider spacings.

So it remains - Anyone out there got one of the rounded ClubIIBs to check?!?

cheers

Mike
Logged

pgroff

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1827
Re: Reed block measurements on Hohner Club II
« Reply #8 on: December 19, 2010, 02:54:29 PM »

Hi Sandy & Mike,

I don't have the model you specifically asked for (though there seem to be a lot of that model for sale these days on ebay!).

But after Christmas I will be working in my stored leftover inventory of parts and projects and if you like I can check many accordion bodies and reedblocks. This includes a good few Hohner clubs, pre-Coronas, Corsos etc etc.  PM me the exact details of the blocks you need (the number of reeds/block and other measurements besides the 17 mm center-center hole spacing) and I may be able to find what you need.

PG
« Last Edit: December 19, 2010, 02:56:09 PM by pgroff »
Logged

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Logged

Sandy Flett

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 709
    • Accordion and Melodeon Blog
Re: Reed block measurements on Hohner Club II
« Reply #10 on: January 01, 2011, 05:28:01 PM »

Firstly, thanks pgroff and Rob2Hook for your helpful posts.

Mike and I have now been able to discount the IIB from our search, thanks to the following eBay ad which includes a picture of the reed blocks: http://cgi.ebay.co.uk/Button-ACCORDION-HOHNER-CLUB-II-B-Melodeon-REFURBISHED_W0QQitemZ190485230709QQcategoryZ16218QQcmdZViewItemQQ_trksidZp4340.m263QQ_trkparmsZalgo%3DDLSL%252BSIC%26its%3DI%26itu%3DUCI%252BIA%252BUA%252BIEW%252BFICS%252BUFI%252BDDSIC%26otn%3D8%26pmod%3D260709731853%252B260709731853%26po%3D%26ps%3D63%26clkid%3D6063694756531227806

Since in this 2-voice instrument there is room for a third reed block for the accidentals row Hohner has gone for their standard reed-chamber spacing. From this it would seem reasonable to deduce that it is only the Club III (or above) models which include the accidentals in the main reed blocks, resulting in the smaller chamber hole spacing we are after.
Logged
DG Dino Baffetti Carnival II (plus accordions)
Accordion and Melodeon blog

pgroff

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1827
Re: Reed block measurements on Hohner Club II
« Reply #11 on: January 01, 2011, 05:45:23 PM »

Hi again Sandy, Mike, and all.

Happy New Year!  I can tell you that most no-switch Club III accordions I have seen have three rows of pallets on the soundboard.

(See this thread for some exceptional prewar Hohner Club accordions with more than 3 melody reeds that have only 2 rows of pallets on the soundboard):

http://forum.melodeon.net/index.php/topic,3141.0.html


Today I dug out a grey Club III, a grey Club IV, and a brown, wood finish Club III that is early enough to have the small, screw center buttons (as well as a 28 key melody layout, and a lovely action with coil tension springs).  The Club IV has a coupler switch behind the keyboard to take out the bassoon reeds (despite the "Club IV" name, there are only 3 melody voices, LMM).  The two Club III accordions are both MMM.

Of these three accordions, only the wood finish Club III with the small screw-center buttons has but two rows of pallets on the soundboard.  The center-to-center spacing of the airway holes in the reedblocks on this one is about 17.6 mm.

But the reedblocks of a Hohner Corona IIIR here (with couplers) have the 17 mm spacing.  Wonder about the no-coupler Corona III?


PG

edited to add:  OK, reedblocks of a pre-Corona III (MMM, no switch) have close to 19 mm spacing.  and, corrected a typo!
« Last Edit: January 03, 2011, 01:21:58 AM by pgroff »
Logged

Sandy Flett

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 709
    • Accordion and Melodeon Blog
Re: Reed block measurements on Hohner Club II
« Reply #12 on: January 12, 2011, 03:58:16 PM »

Mike has now had access to an early Hohner Club III - the same as the one on the left in pgroff's picture above, with the screwed-in treble buttons - and is satisfied its dimensions are close enough to meet our needs.

On revisiting pgroff's link to the Dec 2009 thread on "Hohner Modell 234, 235, 255 and other prewar clubs with 4 (+) voices", I think there may be a good chance that the late 1920's models identified in the following list from Matthew B might all be of the same or close reed block dimensions.

... looking at Hohner's model list online it looks as if the club system was around in the mid-twenties.  They have several models listed from that period.  A quick scan turned up the following:

AMATI, Club, 23+2, 1925-27, 35, 40, 53, 57, 61, 83-87
CLUB III , Club, 23+7, 1928-37
MODELL 234, Club 23+4, 1928-35
LA CONTESSA Club, 23+2, 1929
L'ORGANOLA Club, 23+2, 1929
No. 3565, Club 21+2, 1929

So I am off to trawl eBay, but will also put a post on melnet Buy and Sell in case any melnetters have one of these they would not mind some money for.

Many thanks to pgroff and Matthew B whose inputs have been incredibly helpful in moving our quest forward.
Logged
DG Dino Baffetti Carnival II (plus accordions)
Accordion and Melodeon blog

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reed block measurements on Hohner Club II
« Reply #13 on: January 12, 2011, 06:14:55 PM »

It might be a whole lot easier to just get Mike to build some reedblocks for you!
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal