Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Replace leather valves on Hohner Pokerwork?  (Read 5578 times)

0 Members and 1 Guest are viewing this topic.

docEdock

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
  • Hohners, Gaillards, Castagnaris
    • LoafingAboard
Replace leather valves on Hohner Pokerwork?
« on: December 24, 2010, 12:12:24 PM »

My Hohner A/D will be keeping its current tuning, since as Theo advises, G/C reed blocks are quite dear. I keep running out of air and am tempted to blame curled valve leathers. See photos 12-18 at http://picasaweb.google.com/docedoc123/Hohner?authkey=Gv1sRgCKCG2LWAu7rE2wE# for details. Do these leathers need to be replaced or is it more likely that I need air button lessons?

Logged
How difficult can it be?
http://loafingaboard.blogspot.com/

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Replace leather valves on Hohner Pokerwork?
« Reply #1 on: December 24, 2010, 02:24:12 PM »

New valves will make you a big difference.  A lot of air is wasted pulling those valves back in, and some are so bad they may never close. 

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Replace leather valves on Hohner Pokerwork?
« Reply #2 on: December 24, 2010, 02:41:48 PM »

But to do a worthwhile job you need to replace the valves under the reedplates as well whic means taking all the reedplates off and replacing all the wax,  a substantial task.

There are many other possible ways that air can escape which should be checked first.

The other thing to be aware of is that it's very common for new players to struggle with air management becaues they tend to play more slowly, tend to play legato, and tend to play louder than necessary, and may not have learned to use the air valve effectivly.  Please check out all these areas first. 

I'm not saying that the valves don't need replacing,  just that there is a whole range of factors at work here.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Replace leather valves on Hohner Pokerwork?
« Reply #3 on: December 24, 2010, 04:45:07 PM »

Good points, Theo, an accordion that's been around a bit could have leaks in other areas too.  It takes very little lost air to make a difference.

docEdock

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
  • Hohners, Gaillards, Castagnaris
    • LoafingAboard
Re: Replace leather valves on Hohner Pokerwork?
« Reply #4 on: December 30, 2010, 10:56:53 AM »

Well, it's a poor workman that blames his tools, even if the chisel was used as a screwdriver in the past.

I think I'll defer any Hohner surgery until I'm further along in my journey. Perhaps my A/D will get smarter at conserving air as I proceed, poor stupid thing that it is. Here I'm reminded of my father and how extraordinary was his learning curve in the previous four years, when I turned twenty.
Logged
How difficult can it be?
http://loafingaboard.blogspot.com/

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Replace leather valves on Hohner Pokerwork?
« Reply #5 on: December 30, 2010, 02:58:23 PM »

I think I'll defer any Hohner surgery until I'm further along in my journey. Perhaps my A/D will get smarter at conserving air as I proceed, poor stupid thing that it is. Here I'm reminded of my father and how extraordinary was his learning curve in the previous four years, when I turned twenty.
I'm a learner and couldn't believe how much air I used when I first started. Maybe if you can find a mentor it might help. I was playing very legato and holding notes far too long.
However, as others have pointed out, those valves would never pass the EEC test for a straight banana  ::) and they ain't helping. I have been doing some work on a concertina with curly valves, and sorting them out made a noticeable difference to responsiveness and air use. Might not be such an issue on a melodeon which is maybe moving more air.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Quebecois

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1206
  • Accordez-vous donc, c'est si beau, l'accordéon!
Re: Replace leather valves on Hohner Pokerwork?
« Reply #6 on: December 30, 2010, 04:48:07 PM »

Might not be such an issue on a melodeon which is maybe moving more air.
Everything counts, but from your pictures there seems to be a few large valves that are completely curled up and these are the ones that should get attention in order to make a difference in the 'air management' area, IMHO.
Logged
Hohner Morgane D/G, pre-Erica Hohner in C/F and G/C,
Hohner Erica A/D, Roland FR-18

docEdock

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
  • Hohners, Gaillards, Castagnaris
    • LoafingAboard
Re: Replace leather valves on Hohner Pokerwork?
« Reply #7 on: January 02, 2011, 12:46:01 PM »

However, as others have pointed out, those valves would never pass the EEC test for a straight banana  ::) and they ain't helping.

Everything counts, but from your pictures there seems to be a few large valves that are completely curled up and these are the ones that should get attention in order to make a difference in the 'air management' area, IMHO.

But to do a worthwhile job you need to replace the valves under the reedplates as well whic means taking all the reedplates off and replacing all the wax,  a substantial task.

Is there a way to retrain the leather in situ to make it pass the ECC straight banana test? This is obviously a slacker question, aimed at avoiding the effort of doing it the right way, which as Theo advises, isn't as easy as it sounds. Plus, the reed wax job still has that original gleam and the leathers are, I believe, original equipment of the highest Swiss postwar standards.

I'm thinking that over time the leather has learned bad habits. What about weighting it down for a while -- years in a straight jacket perhaps? Or using chemistry to reverse the curve -- a sort of pharmaceutical approach? Or something even more persuasive like . . . hot irons?

I'm considering experimenting on the big outside leathers, since replacing a botched job won't involve removing the wax. Surely someone has tried straightening leather valves and succeeded, though I suspect that I'll hear most attempts have failed. That's valuable advice too so don't hesitate to scoff.

Doc
Logged
How difficult can it be?
http://loafingaboard.blogspot.com/

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Replace leather valves on Hohner Pokerwork?
« Reply #8 on: January 02, 2011, 12:55:01 PM »

Doc, there is no fountain of youth for valve leathers.  You just can't fix old and tired. ;D

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Replace leather valves on Hohner Pokerwork?
« Reply #9 on: January 02, 2011, 01:24:41 PM »

Doc, there is no fountain of youth for ...  You just can't fix old and tired. ;D

Let me know if he's wrong! (Just crawled, yawning from bed - must be midday, then)

Rob.

P.S. note there is no sleeping emote.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Replace leather valves on Hohner Pokerwork?
« Reply #10 on: January 02, 2011, 02:25:35 PM »


Is there a way to retrain the leather in situ to make it pass the ECC straight banana test?

There is a temporary fix which is to put a shim under the leather to support it then stroke the leather with the tip of a screwdriver blade.  The idea is to stretch the surface layers of the leather as the blade slides, so you have to use a firm pressure.  This should cause the leather to lie flatter for a while but remember:
Doc, there is no fountain of youth for valve leathers.  You just can't fix old and tired. ;D
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

docEdock

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
  • Hohners, Gaillards, Castagnaris
    • LoafingAboard
Re: Replace leather valves on Hohner Pokerwork?
« Reply #11 on: January 02, 2011, 03:18:20 PM »

There is a temporary fix which is to put a shim under the leather to support it then stroke the leather with the tip of a screwdriver blade. 

Ah, a more holistic approach: whole body massage and perhaps a little aroma therapy thrown in to boot? I remember, as a kid, slathering my fielder's mitt with Neatsfoot oil and whacking the pocket with my fist, in the hope that doing so would make me play like Mickey Mantle. Now I want to play like Cyrille Brotto. I wonder if that bottle of oil somehow survived the years?

It is a sad truth that you can't fix old and tired. But, hey, it can't hurt to try. Theo, thanks for the tip. Pictures to follow, eventually.
Logged
How difficult can it be?
http://loafingaboard.blogspot.com/

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Replace leather valves on Hohner Pokerwork?
« Reply #12 on: January 02, 2011, 03:26:00 PM »

Whatever you do don't put any neatsfoot on any of the leather anywhere in a squeezebox!
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Replace leather valves on Hohner Pokerwork?
« Reply #13 on: January 02, 2011, 04:07:11 PM »

Whatever you do don't put any neatsfoot on any of the leather anywhere in a squeezebox!
Interesting - I've heard it recommended. What does it do (in a squeezebox)?
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Replace leather valves on Hohner Pokerwork?
« Reply #14 on: January 02, 2011, 04:16:37 PM »

It leaves the surface slightly sticky which attracts dust.  Its designed for horse tack and other heavy leather that needs to be water resistant.  When the kind if fine leather used in instruments gets stiff, brittle and weak then its like blafleur  says.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

docEdock

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
  • Hohners, Gaillards, Castagnaris
    • LoafingAboard
Re: Replace leather valves on Hohner Pokerwork?
« Reply #15 on: January 02, 2011, 04:43:51 PM »

Whatever you do don't put any neatsfoot on any of the leather anywhere in a squeezebox!

Ah, another blind alley. Probably accounts for why I didn't make the majors. Thanks for the warning.
Logged
How difficult can it be?
http://loafingaboard.blogspot.com/

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Replace leather valves on Hohner Pokerwork?
« Reply #16 on: January 02, 2011, 06:40:28 PM »

Doc, if you're handy at all, re-leathering, re-waxing, and leak chasing is a big, but not difficult job.  I think there are quite a few threads on this forum on the topic, if not there are plenty here who could help.  Now tuning, which you surely need anyway, is quite another thing.

I think you'd be amazed at what a difference the job would make in both sound quality and playability.

docEdock

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
  • Hohners, Gaillards, Castagnaris
    • LoafingAboard
Re: Replace leather valves on Hohner Pokerwork?
« Reply #17 on: January 02, 2011, 08:08:03 PM »

Doc, if you're handy at all, re-leathering, re-waxing, and leak chasing is a big, but not difficult job.  I think there are quite a few threads on this forum on the topic, if not there are plenty here who could help.  Now tuning, which you surely need anyway, is quite another thing.

I think you'd be amazed at what a difference the job would make in both sound quality and playability.

Thanks for the advice. I'm sure you're right. I've been following http://forum.melodeon.net/index.php/topic,5547.0.html and admiring how Telemorris doesn't hesitate to tear his Pokerwork down to the bones and the detailed advice he's gotten about building it back up. As for handy that's hard to say. I  did build a boat and it does still float so perhaps I'll not sink my Hohner though it is, in comparison, such a delicate little thing.

About the tuning. I suspect it is tuned very wet, even sodden. The beat(?) on the higher notes seems awfully strong. If I manage to post La Marianne as my first TOTM I'm sure I'll be able to find out if others think so as well.
Logged
How difficult can it be?
http://loafingaboard.blogspot.com/

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Replace leather valves on Hohner Pokerwork?
« Reply #18 on: January 03, 2011, 01:21:21 AM »

In my little book, building a boat qualifies as a step or two above handy.

docEdock

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
  • Hohners, Gaillards, Castagnaris
    • LoafingAboard
Re: Replace leather valves on Hohner Pokerwork?
« Reply #19 on: January 03, 2011, 12:31:57 PM »

Over on woodenboat the sages often add, "as long as you don't drown" as the bottom-line measure of success. So far so good. The rest is just cosmetics.
Logged
How difficult can it be?
http://loafingaboard.blogspot.com/
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal