Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Making a new reed block bottom plate.  (Read 2955 times)

0 Members and 1 Guest are viewing this topic.

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Making a new reed block bottom plate.
« on: January 04, 2011, 09:08:43 PM »

I need to replace the bottom plate on one of the bass side reed blocks. It has cupped across the short dimension.

Making a new piece with felt attached to one side if easy. Has anyone here made a new plate and done the drilling of the holes through both wood and felt? I'm wondering what kind of drill bit is the best for creating a clean hole through both wood and felt? Is a Forstner bit the right thing to use? I don't think Hohner could have used Forstner bits early last century since I think the Forstner bit is a relatively new design though I could be way off on that one.
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

strad

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 418
Re: Making a new reed block bottom plate.
« Reply #1 on: January 04, 2011, 10:34:19 PM »

I would think clamping the wood/felt to a sacrificial piece of wood woul do the trick - obviously with the felt as the jam in the sandwich.

Nigel
Logged

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Making a new reed block bottom plate.
« Reply #2 on: January 04, 2011, 10:46:21 PM »

Clamping the felt as the "jam" between the plate and another board makes sense. I was planning to do that already. I'm just wondering which kind of drill bit design to use. Maybe standard drill bits (what I have) are fine.
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Andy Simpson

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 938
Re: Making a new reed block bottom plate.
« Reply #3 on: January 04, 2011, 10:57:35 PM »

Firstly, felt isn't a terribly good gasket material and everyone now uses either soft leather or neoprene. Secondly, putting the gasket on the reedblock isn't done anymore, modern Hohners and every other make of accordion I've seen have the gasket glued to the baseboard with nothing on the reedblock.

How much has it cupped anyway?, it would have to be an awful lot to warrant rebuilding IMO. I'd be surprised if it couldn't just be sanded out reasonably flat and work perfectly well with a gasket of adequate thickness on the baseboard.

As for drill bits, why not try it on scrap with whatever it is you have to hand?. A Forstner bit, (invented in the 1870s), would obviously get the cleanest cut but brad point bits would be adequate, a bit faster and cheaper.
« Last Edit: January 04, 2011, 11:03:30 PM by Andy Simpson »
Logged

acctech

  • Member
  • *
  • Offline Offline
  • Posts: 49
  • Crazy for free reeds!
    • Limex USA
Re: Making a new reed block bottom plate.
« Reply #4 on: January 04, 2011, 11:30:14 PM »

Unless there is some other damage, the easiest solution is to sand the block flat with 120 grit paper on a hard flat surface. This is a fairly routine method for this problem. It may be necessary to shim the block back tight.
Logged
Professional Accordion Technician since 1999
Diatonic accordions of all kinds! Piano accordion too :-)

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Making a new reed block bottom plate.
« Reply #5 on: January 04, 2011, 11:51:13 PM »

BUt if that does not work, drill the wood first start with a pilot hole of 1 to 2mm, then drill halfway from each side to avoid any splintering.  I forstner bit would be good, but any bit with a cutting lip would be equally effective.  Glue the gasket material on afterwards (I agree with not felt)  and when the glue is cured cut out the vents with a scalpel. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Making a new reed block bottom plate.
« Reply #6 on: January 05, 2011, 12:32:06 AM »

Firstly, felt isn't a terribly good gasket material and everyone now uses either soft leather or neoprene. Secondly, putting the gasket on the reedblock isn't done anymore, modern Hohners and every other make of accordion I've seen have the gasket glued to the baseboard with nothing on the reedblock.

How much has it cupped anyway?, it would have to be an awful lot to warrant rebuilding IMO. I'd be surprised if it couldn't just be sanded out reasonably flat and work perfectly well with a gasket of adequate thickness on the baseboard.

As for drill bits, why not try it on scrap with whatever it is you have to hand?. A Forstner bit, (invented in the 1870s), would obviously get the cleanest cut but brad point bits would be adequate, a bit faster and cheaper.

Thanks for all the advice. I'll take a look at the cupping when I get home tonight. If memory serves, the cupping is fairly pronounced. Sanding would leave little wood.

As for the use of leather as a gasket: I'm in the process of rebuilding a Presswood Pokerwork. If I need to take the old felt off the bottom of one of the reed blocks, should I pull it off of the other and glue leather over the matching section of the baseplate/fondo? What thickness and type of leather should I use? Would chamois be acceptable (I have some) or should I use something different?
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Making a new reed block bottom plate.
« Reply #7 on: January 05, 2011, 09:00:33 AM »

I would leave the gasket material where it is,  there is no great advantage in having on the baseboard. 
As for material, chamois could be ok if you can select a piece with an even thickness, the chamois sold for washing cars can be very patch in thickness, but good quality stuff would be ok.  Other leather would have to be similar thickness to the original and soft in texture.  Italian makers use a woven synthetic material with a velvet pile on one side.  Contact me by email if you want me to send you some.  Its main advantage in my experience is that it is much easier to cut and trim than soft leather.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Making a new reed block bottom plate.
« Reply #8 on: January 05, 2011, 07:33:02 PM »

Other leather would have to be similar thickness to the original and soft in texture.  

There's enough curvature in the bottom plate that I'll be removing two to three mm of wood to get the bottom plate flat. I'll need to make up the difference in thickness with the felt/leather/fabric somehow. Maybe I'll need to use some of the felt and leather for pallet facing from CGM to make that work. I am also interested in your Italian fabric. I've sent you an email about that separately. Thanks for the offer Theo.
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Making a new reed block bottom plate.
« Reply #9 on: January 05, 2011, 08:28:29 PM »

You don't need to rebuild the thickness that you have removed. Use a single sheet of gasket, fit the reedblocks and then adjust the fasteners that hold the reedblocks in place by shimming with a piece of wood or hard leather.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Making a new reed block bottom plate.
« Reply #10 on: January 05, 2011, 09:00:17 PM »

You don't need to rebuild the thickness that you have removed. Use a single sheet of gasket, fit the reedblocks and then adjust the fasteners that hold the reedblocks in place by shimming with a piece of wood or hard leather.

Thank you very much Rees!

I should have thought of that myself. So simple it could have bitten me but that's why I ask these questions.
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Making a new reed block bottom plate.
« Reply #11 on: January 05, 2011, 09:33:23 PM »

simple is good  (:)
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal