Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2 3   Go Down

Author Topic: Faceplate(soundboard) holes  (Read 11508 times)

0 Members and 1 Guest are viewing this topic.

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Faceplate(soundboard) holes
« on: January 05, 2011, 05:22:22 PM »

I notice some builders use exclusively square holes, some round.  Any reason to pick one over the other?  Any tonal differences?

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Faceplate(soundboard) holes
« Reply #1 on: January 05, 2011, 05:29:03 PM »

This is just my guess, but...  for a give reed spacing along the block a square hole has a 30% larger area than a round hole of the same width, therefore more room for air and sound to pass.  In theory it should make the box capable of playing louder.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: Faceplate(soundboard) holes
« Reply #2 on: January 05, 2011, 05:45:15 PM »

I think that my Bouebe has square holes for the inside pallets and round for the outside, presumably to try to make sure that the rows sound at the same volume through the same principle that Theo has mentioned.
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Faceplate(soundboard) holes
« Reply #3 on: January 05, 2011, 05:57:11 PM »

Theo, my only experience is with round holes, are the holes typically the same width?  I had experimented a while back with different size holes.  I started at 3/8" (9.53mm), where the sound seemed slightly choked and muffled, and increased size 1/64th(.34mm) at a time, the sound gradually became louder and clearer, then started using noticeably more air.  But I would imagine that there's all kinds of variable that can come into play here.

Have you ever noticed a tonal difference?

Christopher K.

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 894
Re: Faceplate(soundboard) holes
« Reply #4 on: January 05, 2011, 06:02:13 PM »

Is there an easy way of cutting a square hole without a CNC machine?

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Faceplate(soundboard) holes
« Reply #5 on: January 05, 2011, 06:10:14 PM »

Is there an easy way of cutting a square hole without a CNC machine?

A mortised bit will cut a square hole using a pillar drill

http://en.wikipedia.org/wiki/Mortiser

Christopher K.

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 894
Re: Faceplate(soundboard) holes
« Reply #6 on: January 05, 2011, 09:51:03 PM »

Is there an easy way of cutting a square hole without a CNC machine?

A mortised bit will cut a square hole using a pillar drill

http://en.wikipedia.org/wiki/Mortiser

Thanks Lester! 'suppose Google could have turned that up for me.  ;D

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Faceplate(soundboard) holes
« Reply #7 on: January 05, 2011, 09:59:49 PM »

Theos' guess is correct. There is a significant tonal difference, especially when it comes to larger (Italian) reeds.  It doesn't seem to affect the relatively small Hohner reeds in the same degree. The well known German expert in accordion acoustics, Gotthard Richter, touches  the subject quite extensively in  his book "Akkordeon, Handbuch für Instrumentenbauer".
Is there an easy way etc.:  Use a simple frame saw, if it's just for 1 instrument.  There are, after all, not that many holes.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Faceplate(soundboard) holes
« Reply #8 on: January 05, 2011, 10:07:08 PM »

Or drill circular holes and cut out the corners with a file.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Christopher K.

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 894
Re: Faceplate(soundboard) holes
« Reply #9 on: January 06, 2011, 01:40:13 AM »

Or drill circular holes and cut out the corners with a file.

Files were my first idea. Marking out the edges of the square holes with pencil lines would probably make it easier to determine the centers for the circular bit in the first place?

I've noticed very old German single-row accordions that have square or rectangular holes behind the pallets.. never examined one up close, just seen photos.


blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Faceplate(soundboard) holes
« Reply #10 on: January 06, 2011, 03:12:20 AM »

Diatonix, do you know if the square holes are the same cross section as the diameter of a round one, or is it smaller?  A square hole of the same size as the diameter of a round one would be a substantial air flow difference.  Based on my hole enlargement experiment, I would have anticipated that would be too much air, but again, lots of variables come into, play, besides my ignorance.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Faceplate(soundboard) holes
« Reply #11 on: January 06, 2011, 09:10:35 AM »


Marking out the edges of the square holes with pencil lines would probably make it easier to determine the centers for the circular bit in the first place?

Mark the centres first, much more accurate, and a marking knife would be better than a pencil.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Faceplate(soundboard) holes
« Reply #12 on: January 06, 2011, 09:13:04 AM »

Files were my first idea. Marking out the edges of the square holes with pencil lines would probably make it easier to determine the centers for the circular bit in the first place?

I agree with Theo - mark a line for the centres first and then divide it up into the correct centre spacing. Then add additional lines to delineate the edges of the square holes.  Ensure the edges of all the holes line up on the same parallel straight lines. Use a centre punch or spike to make a small indentation on the centre point before you start to drill. This will help prevent your drill from wandering. After drilling use a square or flat needle file to remove the remaining wood in the corners of the squares.
« Last Edit: January 06, 2011, 09:16:46 AM by Steve_freereeder »
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Faceplate(soundboard) holes
« Reply #13 on: January 06, 2011, 09:24:02 AM »

Steve that method is a lot of unnecessary work, and prone to error.

First off work on a drawing board, or something improvised that can give you the same effect, and some instruments that will give you the functions of a tee square.  Draw the centre line of each row of holes first, mark of the positions of the centres of all the holes,  scribe* a circle for each hole, where the diameter equals the side of the square you want to end up with.  Draw two lines parallel the the centre line, but tangential to the circles, draw vertical lines tangential to the circles to form the other two sides of the square.

* at this point you could make a short cut and drill the holes.

I used to teach tech drawing and I don't like to see people making extra work producing a less accurate drawing!

You could do the drawing on paper, and glue it to the workpiece instead of drawing directly on the wood.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Faceplate(soundboard) holes
« Reply #14 on: January 06, 2011, 09:46:33 AM »

Steve that method is a lot of unnecessary work, and prone to error.
Umm.... I thought the two methods were essentially the same. However, I agree that scribing/marking circles as you describe and then marking tangents is the best way to achieve a rapid and accurate set of lines parallel to the centre lines.

(I've done a lot of engineering drawing/cartography in my time too  ;)  )
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Faceplate(soundboard) holes
« Reply #15 on: January 06, 2011, 09:49:35 AM »


(I've done a lot of engineering drawing/cartography in my time too  ;)  )

I thought you would have Steve, so I was surprised at the method your suggested.

Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Faceplate(soundboard) holes
« Reply #16 on: January 06, 2011, 09:54:57 AM »


(I've done a lot of engineering drawing/cartography in my time too  ;)  )

I thought you would have Steve, so I was surprised at the method your suggested.

I was probably editing my original post at the same time as you were commenting on mine, so you may have been reading an earlier version of mine which I soon abandoned, realising it wasn't the best answer.  :|bl
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Faceplate(soundboard) holes
« Reply #17 on: January 06, 2011, 10:44:06 AM »

Glad we've sorted that out! ;)

Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Faceplate(soundboard) holes
« Reply #18 on: January 06, 2011, 12:59:40 PM »

So are you guys feeling that the improvement in sound is worth all that extra work?  I wondered if square versus round was more of tradition thing.  I'm not opposed to doing a lot of extra work if the gain is there to warrant it.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Faceplate(soundboard) holes
« Reply #19 on: January 06, 2011, 01:34:16 PM »

My guess would be its something to decide when designing the instrument.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning
Pages: [1] 2 3   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal