Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 2 [3]   Go Down

Author Topic: Faceplate(soundboard) holes  (Read 11495 times)

0 Members and 1 Guest are viewing this topic.

Lars

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 797
Re: Faceplate(soundboard) holes
« Reply #40 on: January 09, 2011, 07:32:18 PM »

@lars: what you've pointed out is very true when dealing with smaller reeds, say the last 4 to 6 in a row. My experience teaches me  that larger reeds benefit from more spacious (i.e. deeper, but not longer than necessary) chambers, probably because they allow their valves to fully open.

My point on the spot - obviosly they have to be deep enough for the valve to open up properly, but I have found that adding a shim to the bottom of the chamber to reduce depth has helped. This was in the case where the reed chamber was deeper than most modern (40s onwards) builders would build.

This is also the case when I replace a low set of reeds with a medium set - I reduce both lenth and depth of the chamber on those chambers where I find the depth to be more than what is just needed for the valve to open properly.
Logged

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Faceplate(soundboard) holes
« Reply #41 on: January 09, 2011, 10:13:40 PM »

This reminds me of a Hohner Corso I tuned many years ago: The accidentals were so penetrant to make my hair stand on end. The "problem" was easily solved be reducing the enormous chamber underneath them. However, when the owner returned he was extremely disappointed with the result: he wanted everyone to hear that he actually used his accidentals! I had no choice but to bring back said chambers to their pristine state...
Logged

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Faceplate(soundboard) holes
« Reply #42 on: January 09, 2011, 10:43:19 PM »

Do you gentlemen use tapered reed blocks?

melodeon

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1732
Re: Faceplate(soundboard) holes
« Reply #43 on: January 10, 2011, 05:06:31 PM »

Tapered which direction ?

Across the width, or down the length ?
Logged

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Faceplate(soundboard) holes
« Reply #44 on: January 10, 2011, 07:00:18 PM »

Yes.

strad

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 418
Re: Faceplate(soundboard) holes
« Reply #45 on: January 10, 2011, 08:15:25 PM »

Trapezoidal?

Nigel
Logged

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Faceplate(soundboard) holes
« Reply #46 on: January 22, 2011, 03:37:01 PM »

it did occur to me that round holes (and pads) are much cheaper


 why a box with a substantially square cutout for the reed and valve followed it up with a round hole and pad.


The hole in the reedblock and the hole in the baseboard are virtually always the same shape, either both round or both square, for this very reason.
[/quote]

In my Oakwood -- certainly one of the loudest boxes around -- the holes in the reedblock are square and as large as possible, the holes in the soundboard are rectangular with one big hole for each pallet over two reedblock holes. This gives an even bigger opening for the sound to escape.

Ian
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

Andy in Vermont

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 948
  • Mélodie
    • Melodeon Minutes (blog)
Re: Faceplate(soundboard) holes
« Reply #47 on: January 22, 2011, 07:47:20 PM »

This gives an even bigger opening for the sound to escape.

Ian,
Do you think that it is primarily "for the sound to escape" or to promote airflow?
I've noticed that on many French Canadian boxes, the space on the faceplate between the holes for the two "M" reeds has been hollowed out.

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: Faceplate(soundboard) holes
« Reply #48 on: January 22, 2011, 09:28:32 PM »

Quote
Do you think that it is primarily "for the sound to escape" or to promote airflow?
Sound.
The airflow is limited mostly by the reed (try taking a reed plate out and playing the box with a gaping hole where the reed plate was!)
Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk
Pages: 1 2 [3]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal