Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2] 3 4 5   Go Down

Author Topic: Pitch shift after tuning a reed  (Read 16719 times)

0 Members and 1 Guest are viewing this topic.

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Pitch shift after tuning a reed
« Reply #20 on: January 27, 2011, 05:44:52 PM »

I am quite happily using Dirk's tuner. My methodology is to tune on my tuning rig individual reeds against my tuning plan and then to check/rectify on two reed setting once the reed blocks are in the box. This invariably requires some fine retuning.


Lester, how close are you taking the pitch to your target? Dirks registers differences in pitch to .2 cents which should be close enough given the tremolo. One thing I'm trying to understand is the tolerances in this kind of tuning setup. I'm not used to tuning two reeds and finding that they can and do pull each other out of the pitch I set them to.

I'm doing a fairly standard Hohner tremolo using the measurements that Steve_freereeder posted here (look at item number four).

I'm used to tuning my guitar and doing most of it by ear after establishing the A440 but that's for one string. I remember tuning a 12 string being a real challenge and never being happy with the results. Tuning a melodeon feels different since it has the tremolo. I've got an excellent sense of pitch - have had since the age of five, however the tremolo is throwing my ear for a loop.

I think my next step will have to be testing the pitch of each reed independent of the other reed in the pair, then test the two together to see how sounding two reeds together can pull each one out of the pitch that's established independently. I think doing that kind of data gathering may help me understand the situation better.
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Pitch shift after tuning a reed
« Reply #21 on: January 27, 2011, 06:02:09 PM »

Tuning a melodeon feels different since it has the tremolo. I've got an excellent sense of pitch - have had since the age of five, however the tremolo is throwing my ear for a loop.


Here is another approach you can try.  First, using your preferred electronic aid tune one reed(on its own) to the  correct pitch from your table. Next tune the second one approximately using the electronic aid of your choice. Finally listen to the beats produced by the two reeds together and tune the second reed to get your target beat rate.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: Pitch shift after tuning a reed
« Reply #22 on: January 27, 2011, 06:06:08 PM »

You can simulate the effect to some extent with a couple of tone generators, but as j.w.forest has already mentioned there is some physical interaction between the reeds that a simulation would struggle to reproduce.


I think that the physical interaction may be playing a part in what Telemorris is perceiving as his 'shift'. Although without knowing his procedure firsthand, this assumption is only a guess.


I don't see why the coupling between + and - reeds shouldn't apply equally to conventional "concert + sharp" tuning. Keeping one bank on concert and the other the right amount sharp is just as much of a moving target if they affect each other.


  They do,....however, the tuning software is set up with "zero" as a major reference point. It is simply a bit more difficult to construct and follow the tuning model for Dedic. I have imagined a simulated or approximate Dedic tuning, whereby one would calculate the resultant zero and make a compromise. I would like to toss it out to discussion to see if there are any holes in the theory.....it may already have a name and be in use, or tried and discarded! I will start a new thread or resurrect an old one, rather than drift away on this one.
Logged

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Pitch shift after tuning a reed
« Reply #23 on: January 27, 2011, 06:55:05 PM »

Tuning a melodeon feels different since it has the tremolo. I've got an excellent sense of pitch - have had since the age of five, however the tremolo is throwing my ear for a loop.
Here is another approach you can try.  First, using your preferred electronic aid tune one reed(on its own) to the  correct pitch from your table. Next tune the second one approximately using the electronic aid of your choice. Finally listen to the beats produced by the two reeds together and tune the second reed to get your target beat rate.

I plan to do as you suggest, Theo. Tune the concert reed (on its own) to the exact pitch, wait until it's stable every time I play it, tune the second reed to the designed pitch, then play the two together and measure the pitches of the two reeds. I'll get a reading of how much each pulls the other away from the pitches I set them to.

If I tune the concert reed to be on pitch when sounded by itself, but the second reed being sharp by, say eight hertz, pulls the concert reed sharp, I'll have a note that plays off pitch unless I retune the concert pitched reed flat to account for sympathetic sharpening (?) that happens when the two reeds are played together.

This really takes some Dedic-ation!  >:E

And patience - and maybe a beer or two.  :|glug
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Pitch shift after tuning a reed
« Reply #24 on: January 30, 2011, 07:25:53 PM »

I've started tuning in earnest now. I've almost completed the push reeds (easiest to get to) on the D row. I did finally decide to go with the Dedic design and a Hohner tremolo since this Erica will be played for Morris dancers.

One debate I'm having is how to tackle the pull reeds. I've measured and recorded the difference in cents between each reed and the design pitch using Dirk's tuner. Many of the reeds are 20 - 30 cents sharp. Is it better to take the reed plates off the blocks to get at the tongue instead of fishing through the vent with a pinger or the "U" shaped pusher? I don't have a feel yet for how easy it is to push the tongue out of alignment or to increase or decrease the tongue tip clearance by inadvertently bending the base of the tongue with the scratcher or the support. Is 20 - 30 cents a large amount of change when its on the inside or pull reed? Given that I've got to make this amount of change in all the pull reeds on the treble side, do I need to remove the reeds?
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Pitch shift after tuning a reed
« Reply #25 on: January 30, 2011, 07:34:48 PM »

The main problem with doing all the push reeds first, despite them being easier, is that if you have to turn a reed to tune it (I use this if it has to be flattened a far bit because I am not very good at scratching through the plate yet) the push side will almost certainly need re-tuning once you replace the reed the orrect way around. So now I mostly tune he pulls first then the easier pushes

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Pitch shift after tuning a reed
« Reply #26 on: January 30, 2011, 08:10:27 PM »

I do as Lester says and tune the pull reeds first for each respective bank of reeds.  Whether you remove the plate or tune the pull reed in place, you run the risk of messing up the tuning on the push reeds.  I like to tune the pull reeds in place where I can, but on the smaller reeds you have no choice but to remove the plate.  If you need to flatten the pull reed, make sure you still support the reed, flattening through the gap almost always opens up the reed gap and you'll have to pull the base to reset it, for some reason, pulling the pull reed up to sharpen doesn't seem to mess up the gap as much, in fact rarely.  Also, after tuning, methodically go through each individual reed softly checking response.  If you don't get good response, you need to check seals and gaps.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Pitch shift after tuning a reed
« Reply #27 on: January 30, 2011, 08:13:57 PM »

I find the reed plates don't need to be turned to tune them, you just make a huge lot of extra work for yourself doing it that way.  You can use the scratcher to go down 20 or 30 cents, just take your time until you get the feel of it.

Please don't try to learn on a good set of reeds! You probably will make some mistakes, so get a junk piano accordion, take the reedblocks from that and get plenty of practice till you are happy with the technique, then start work on the good box.   That way you can practice using the scratcher, and using one or other of the methods of lifting the pull reed to file the tip if you have to raise the pitch.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Pitch shift after tuning a reed
« Reply #28 on: January 30, 2011, 08:29:45 PM »

I find the reed plates don't need to be turned to tune them, you just make a huge lot of extra work for yourself doing it that way.  You can use the scratcher to go down 20 or 30 cents, just take your time until you get the feel of it.


I 100% agree and I will get better but I need a better scratcher, my current one is too big for more than half the reed slots in a D/G box. Still I'm new to this a practice will make it easier  ;)

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Pitch shift after tuning a reed
« Reply #29 on: January 30, 2011, 08:32:49 PM »

I find the reed plates don't need to be turned to tune them, you just make a huge lot of extra work for yourself doing it that way.  You 

Theo, how do you sharpen the little pull reeds?  I can't do these without turning them.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Pitch shift after tuning a reed
« Reply #30 on: January 30, 2011, 10:50:44 PM »

I'll post a photo tomorrow,  I may need reminding!
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Pitch shift after tuning a reed
« Reply #31 on: January 30, 2011, 11:02:57 PM »

By tomorrow I'll forget all about today, so reminding now. :D
« Last Edit: January 30, 2011, 11:31:52 PM by blafleur »
Logged

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Pitch shift after tuning a reed
« Reply #32 on: January 31, 2011, 04:20:49 PM »

I'll post a photo tomorrow,  I may need reminding!

I too am looking forward to seeing photos of how you tune the smallest pull reeds! Consider this a reminder!
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

waltzman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 943
Re: Pitch shift after tuning a reed
« Reply #33 on: January 31, 2011, 04:50:55 PM »

Me too.  I use a toothpick to push the reed out from the inside.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Pitch shift after tuning a reed
« Reply #34 on: January 31, 2011, 05:13:22 PM »

Ok, ok, ok give me a minute! ::)

Here is a public link to some photos showing the process for the highest reed in a Hohner Preciosa in a facebook album.  You do not need to be a FB member to see these.

Sorry they are not quite sharp, not enough hands to hold everything steady.

What these don't show is how the reed lifter works,   but if you use one on larger reeds the process is the same.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Pitch shift after tuning a reed
« Reply #35 on: January 31, 2011, 05:17:01 PM »

I use a hook on the bigger reeds to go under the push reeds and then push up on the pull reed, but the smaller reeds are too small to do this (at least for me).  So how do you get that reed up?

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Pitch shift after tuning a reed
« Reply #36 on: January 31, 2011, 05:18:52 PM »

So how do you get that reed up?

Using the tool shown in the first picture.  Sorry I'm unable to explain it in words.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

waltzman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 943
Re: Pitch shift after tuning a reed
« Reply #37 on: January 31, 2011, 05:28:51 PM »

Ah, that's the other type of reed lifter that I have never used.  Not even sure where to buy one.  The toothpick technique only works when you have the reed block off in your hand.
Logged

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Pitch shift after tuning a reed
« Reply #38 on: January 31, 2011, 06:00:17 PM »

Thanks for posting, Theo.  I'm assuming it's very thin metal an is passed through the slot and slide under the reed tip?  The tolerance is so tight on good reeds I wouldn't have thought that would work.

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: Pitch shift after tuning a reed
« Reply #39 on: January 31, 2011, 06:02:05 PM »

So how do you get that reed up?

Using the tool shown in the first picture.  Sorry I'm unable to explain it in words.

Is the tool in question like this Theo?

http://flickr.com/gp/47089974@N02/4hF8U7
Logged
Pages: 1 [2] 3 4 5   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal