Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Removing Glued in Reed Blocks  (Read 4337 times)

0 Members and 2 Guests are viewing this topic.

Andrew Culwell

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 620
Removing Glued in Reed Blocks
« on: January 29, 2011, 04:10:11 AM »

I've started a challenging project, restoring a two row International c/c# Melodeon.  The box is in good condition but like all boxes that are 90 years old the glue is crystallized and the blocks on this one are glued to the sound board.  I want to remove the blocks so I can rehab the reeds and valves then re-attach it to the sound board.  The question is how do I remove the reed blocks without breaking the sound board.  I also need to take the sound board frame apart and re-glue it.  The glue is still somewhat stable but beginning to crystallize in areas.  Any ideas?  Below are photos of the sound board and reed blocks.
« Last Edit: January 29, 2011, 04:15:17 AM by A.J. Culwell »
Logged
Hohner's, Paolo Soprani red 4 voice, Paddy Clancy Celtic

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Removing Glued in Reed Blocks
« Reply #1 on: January 29, 2011, 04:20:25 AM »

Why can't you rehab the reeds and leave the reed blocks in place?  I don't see any reason to remove the blocks unless you need to repair or replace them. 

Andrew Culwell

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 620
Re: Removing Glued in Reed Blocks
« Reply #2 on: January 29, 2011, 04:24:25 AM »

Hmm didn't think about that.  I have to examine the reed blocks further to see if they are loose.
Logged
Hohner's, Paolo Soprani red 4 voice, Paddy Clancy Celtic

Andrew Culwell

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 620
Re: Removing Glued in Reed Blocks
« Reply #3 on: January 29, 2011, 04:47:58 AM »

I'm tempted to simply leave the reeds on the blocks remove the old valves and replace them with new ones.  I really just want the box back in playing condition.  I don't even need to have it in perfect tune just wanted to keep it in the original tuning but playable.  I managed to get the soundboard frame off without damaging anything.  The trick is to replace the valves and re-attach the mitred sound board without damaging it. 
Logged
Hohner's, Paolo Soprani red 4 voice, Paddy Clancy Celtic

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Removing Glued in Reed Blocks
« Reply #4 on: January 29, 2011, 10:37:39 AM »

Like blafleur, I don't understand why you can't just remove the reedplates from the blocks as they are, replace the valves, clean the reed tongues etc, and then wax them back in place.  Agreed its tricky getting the wax back on the reedplates between the two blocks, but not impossible, and there is no risk of damaging fragile old woodwork.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Removing Glued in Reed Blocks
« Reply #5 on: January 29, 2011, 01:39:07 PM »

Removing the blocks, I think would be an exercise in frustration, and it's very likely you'd mess up either the blocks, slides, or plates.  I've removed old glued in blocks because I wanted to install better ones, but even not trying to salvage them, it's a bear.

Like Theo said, it's tricky, but it's definitely doable, and a much better option in my mind.  Tuning in blocks like that, like waxing, is doable, but a little tricky.

Good luck.

Andrew Culwell

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 620
Re: Removing Glued in Reed Blocks
« Reply #6 on: January 29, 2011, 02:26:33 PM »

The blocks seem to be solidly glued in and would be extremely difficult to get off so I will do as advised.  It's going to be challenging though!  I took apart the frame of the sound board and it was held in by the nails only the glue had simply disintegrated.  I'll clean the glue off and re-glue the frame back onto the sound board.  You can tell though that the wood is fairly dry and brittle so I will need to be quite careful.
Logged
Hohner's, Paolo Soprani red 4 voice, Paddy Clancy Celtic

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Removing Glued in Reed Blocks
« Reply #7 on: January 29, 2011, 02:31:52 PM »

  You can tell though that the wood is fairly dry and brittle so I will need to be quite careful.

All the more reason for not attempting to remove the blocks.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Andrew Culwell

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 620
Re: Removing Glued in Reed Blocks
« Reply #8 on: February 03, 2011, 03:52:03 PM »

So I'm halfway done removing the reeds from the blocks and am wondering how to go about re-waxing them in, particularly the blocks that face each other and are a small measure apart as shown in the photos.  I was going to use Charlie Marshall's brush method but think that will be a tad difficult if not impossible.  My question is how do I go about waxing the reeds in on these closely placed blocks?
Logged
Hohner's, Paolo Soprani red 4 voice, Paddy Clancy Celtic

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Removing Glued in Reed Blocks
« Reply #9 on: February 03, 2011, 09:11:17 PM »

I use an eye dropper with a bent tip for waxing reeds. I've never used any other method so I can't compare, but it works.  The bottom of stand up reeds facing each other is the hardest, and I do them first.  If the wax is well melted, I can usually start at one end with the accordion tilted down the length of the reed blocks, and give the dropper a push and get the wax about 3/4 to the other end between the reeds, then finish from the other end.  With the right amount of tilt and and side to side tilting while the wax is flowing covers the bottoms, I then use the same method to get between the reeds.  Takes a light touch to keep from flowing the wax too high when it gets to the wax at the bottom of the reeds, you can slow or speed up the wax by tilting more or less.  The upper ends are then easy to get.

I do the bottoms first because when if you do between the reeds first you may get little dams at the bottom that makes it hard to get wax to flow down the bottoms. 

Hard to explain, like asking my grandmother how she cooks.  Surely there is a video on youtube.

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: Removing Glued in Reed Blocks
« Reply #10 on: February 04, 2011, 01:37:46 AM »

I had the same problem and ended up filing one tip of my encaustic stylus down. It worked, but since the stylus itself is fairly pricey it isn't the most economical option. The normal tip of the stylus is very good though for reed plates that are slightly less far apart; piece of cake to wax. Stick the stylus in the wax, draw around reed, repeat.
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal