Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Remove old wax?  (Read 5510 times)

0 Members and 1 Guest are viewing this topic.

HallelujahAl

  • Guest
Remove old wax?
« on: February 15, 2011, 10:56:39 AM »

Now I'm sure there's a been a thread on this before but my searching has been in vain - so here's the question. I want to remove the old wax from a set of reedblocks and re-wax the reeds etc, but what's the best way of removing the old wax? Last time I did this I made a disgusting mess - surely there's a nice clean method of stripping the old wax off  ???
Regards
AL
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Remove old wax?
« Reply #1 on: February 15, 2011, 11:04:23 AM »

Al, if there is a clean method I'd love to know it!  If the wax is old you get powdery dust everywhere,  if its fresh and soft it sticks to your fingers, tools etc.

Old dry wax might get less dusty if you warm the blocks carefully,  fresh wax gets less sticky when cold.   But the best method I've found is just to cover your work table with a sheet of newspaper, and wear an apron or overalls to protect your clothes.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Martyn

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 455
  • Hohnerohner
    • Martyn White Melodeon Tuning and Repairs
Re: Remove old wax?
« Reply #2 on: February 15, 2011, 11:05:05 AM »

Now I'm sure there's a been a thread on this before but my searching has been in vain - so here's the question. I want to remove the old wax from a set of reedblocks and re-wax the reeds etc, but what's the best way of removing the old wax? Last time I did this I made a disgusting mess - surely there's a nice clean method of stripping the old wax off  ???
Regards
AL

I use an old blunt half inch chisel and use it over the bin......It works a treat for me.

Martyn
« Last Edit: February 15, 2011, 11:09:46 AM by martyn »
Logged
'Anything from a small repair to a full restoration'.
www.melodeonrepairs.co.uk

Alan Morley

  • Alan Morley
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1190
    • Soundcloud
Re: Remove old wax?
« Reply #3 on: February 15, 2011, 11:31:54 AM »

Would a soldering iron work - possibly a daft suggestion....
Logged
ISIS Melodeon, Hohner Erica,  Fender Strat Plus, Takamine, Hofner Violin Bass, Hohner CX12 Harmonica, etc..

old geezer

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 241
  • Hohner Melodeon
Re: Remove old wax?
« Reply #4 on: February 15, 2011, 11:50:24 AM »

Would a soldering iron work - possibly a daft suggestion....

yep; your right
Logged
Jack Murphy    beyond the black stump

pete /acorn

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 930
  • .Cast Trilly
    • Acorn Instruments
Re: Remove old wax?
« Reply #5 on: February 15, 2011, 12:48:27 PM »

Hi'
Would it not work if you put the blocks in a plastic bag then placed in freezer over night,the wax could become brittle and come off easily.
never tried it though.

Pete
Logged
Acorn Instruments are specialist retailers of Castagnari Instruments,and have an extensive stock of new instruments on the shelf for prompt delivery in standard layouts however these can easily be changed to customers special requirements,we have over 600 reeds in stock
 We also have the largest stock in the UK of  pre loved melodons all fully serviced,and with 12 months warranty
UK and international customers catered for
www.acorninstruments.co.uk

rmenhinick

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 113
Re: Remove old wax?
« Reply #6 on: February 15, 2011, 01:07:10 PM »

Would a soldering iron work - possibly a daft suggestion....

Maybe a hair-dryer/hot air gun used carefully to wark the old wax and then use a desoldering pump to suck out the molten wax?

I used to strip old circuit boards of valuable components by heating the solder with a hot air gun and then sucking away the molten solder using a vacuum cleaner with a reduced hose and an old metal pen tube.
Logged
Old G Poker, New DG Poker, ADG Compadre, DG Sandpiper, CF Erica, GC Delicia Popular, DG Dino Baffetti Black Pearl 3, Casali Verona 48 bass PA, (Squeezebox Squirrel :D)

LJC

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 527
Re: Remove old wax?
« Reply #7 on: February 15, 2011, 01:15:02 PM »

A blunt old butter knife and lots of news paper works a treat for me. Just don't open the windows if there is even a breath of wind as this is a sure fire way to have the whole mess dumped on the carpet.
Logged

HallelujahAl

  • Guest
Re: Remove old wax?
« Reply #8 on: February 15, 2011, 01:51:04 PM »

This is really helpful guys - thanks for all your advice. However, I fear I'll still be making a complete and utter mess again  ;D
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Remove old wax?
« Reply #9 on: February 15, 2011, 01:52:22 PM »

A blunt old butter knife and lots of news paper works a treat for me.

I have one of those, but with the end cut off square which is very hand for getting into corners.

My other favourite tool for this job is a soft wire brush, either brass wire as used for suede shoes, or stainless steel wire which is available through the antiques trade for cleaning chemically softened paint by 'dip and strip' people.

This is really helpful guys - thanks for all your advice. However, I fear I'll still be making a complete and utter mess again  ;D

Its the only way!
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: Remove old wax?
« Reply #10 on: February 15, 2011, 02:12:14 PM »

Now I'm sure there's a been a thread on this before but my searching has been in vain - so here's the question. I want to remove the old wax from a set of reedblocks and re-wax the reeds etc, but what's the best way of removing the old wax? Last time I did this I made a disgusting mess - surely there's a nice clean method of stripping the old wax off  ???
Regards
AL

I use an old blunt half inch chisel and use it over the bin......It works a treat for me.

Martyn

I use something similar, I found that CGM's bass pinger, which is I think supposed to be a shim works very well. Obviously you don't want to gouge the wood, so it leaves a very thin layer. This can be taken off easily with a suede shoe brush, which was a great tip from Theo. Works a treat. Doing it over the bin is important, otherwise it goes everywhere!
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Remove old wax?
« Reply #11 on: February 15, 2011, 03:20:11 PM »

My weapon of choice is a metal 6" ruler.

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: Remove old wax?
« Reply #12 on: February 15, 2011, 08:22:01 PM »

I formerly used a  razor-sharp utility knife blade, and held it with edge flat as one would with a cabinet scraper, lots of paper underneath to catch the debris. Leaves a clean polished surface for re-waxing. Have since graduated to a small tool used for scraping paint, etc. from window glass. It uses a single edge razor blade and offers a much better grip for control. Also works well for trimming ends of leather or mylar valves when you get to installing them.
Logged

Stockaryd

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 255
Re: Remove old wax?
« Reply #13 on: August 17, 2017, 07:04:48 AM »

This thread was useful.   (:)
Logged
Hohner Corso, Hohner Erica, Emmanuel Pariselle, Gessner,   Koch,   Mariotti,    "China  NoName",   4 Toy,     -and now some more

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Remove old wax?
« Reply #14 on: August 17, 2017, 07:36:04 AM »

I formerly used a  razor-sharp utility knife blade, and held it with edge flat as one would with a cabinet scraper, lots of paper underneath to catch the debris. Leaves a clean polished surface for re-waxing. Have since graduated to a small tool used for scraping paint, etc. from window glass. It uses a single edge razor blade and offers a much better grip for control. Also works well for trimming ends of leather or mylar valves when you get to installing them.

I use a scalpel with a fresh blade, used like a cabinet scraper as above. Works for me.

Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Remove old wax?
« Reply #15 on: August 17, 2017, 08:27:44 AM »

Like Owen, I use one of Charlie's bass pinger (which I've found that I hardly actually use for its original purpose) to remove as much wax as I can.

I use something similar, I found that CGM's bass pinger, which is I think supposed to be a shim works very well. Obviously you don't want to gouge the wood, so it leaves a very thin layer. This can be taken off easily with a suede shoe brush, which was a great tip from Theo. Works a treat. Doing it over the bin is important, otherwise it goes everywhere!

I have sometimes then used a small cloth pad or cotton bud soaked in acetone to remove any residual wax film - although I'm not sure how necessary this is if I'm simply going to replace with fresh wax. 
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Remove old wax?
« Reply #16 on: August 17, 2017, 09:09:55 AM »

I use a blade as a scraper, like GPS. Then once it's mostly clean I go over the block with a brass brush (suede brush) to remove all the remnants, then a going over with my industrial vac to remove any debris from the brushing.

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Remove old wax?
« Reply #17 on: August 17, 2017, 11:29:37 AM »

My weapon of choice is a metal 6" ruler.

+1

Kinda substitute blunt chisel and cabinet scraper...

Rob.
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Remove old wax?
« Reply #18 on: August 17, 2017, 11:40:18 AM »

On the blocks which I've stripped, most of the wax has easily broken off with a thumb. The residue comes away with a Stanley knife blade dragged across the apertures from the base to the top, finishing off with a few strokes from a largish flat file, just to make sure that the surfaces are actually flat before refitting the reedplates.
Of course, it's messy; but who amongst us doesn't have a vacuum cleaner?
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Remove old wax?
« Reply #19 on: August 17, 2017, 05:17:39 PM »

I leave it to Theo, Roger T or Martyn White. Then I have no problem at all  8)
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal