Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Internal mics?  (Read 4121 times)

0 Members and 1 Guest are viewing this topic.

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Internal mics?
« on: June 16, 2008, 01:30:43 PM »

I think I screwed up my last attempt to post this subject.

I'm using a pair of AKG C416Ls on my boxes, with generally good results.  I've previously used Microvoxes and built similar mic arrays from a bucket of electret capsules a friend gave me.  Before that, I had a Dino Baffetti three voice with a built-in, internal system with three mics on the treble end and a serpentine cable through the bellows, attached to each fold (!) to a single bass element.

As the poor old arms are getting weaker and my Hohner four-stop left me with numb forearms after each tune, I traded up to a Castagnari Max.  I fitted the AKG to the treble side, but the bass side hasn't a large enough flat surface to mount the bass!  I am considering putting a capsule in the bass side and a pluggable lead to the battery/mixer box (AKG B29).  Anyone know of a good reason not to try it?
Logged

Howard Jones

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1203
Re: Internal mics?
« Reply #1 on: June 16, 2008, 08:05:38 PM »

Assuming a decent-quality mic, no.  As recommended by Andy Cutting, I use an old Tandy PZM, unscrewed from its metal base-plate and screwed onto the inside of the bass end.  It works fine.  I send it to a separate channel rather than trying to connect to the AKG's power supply.

The trouble is, these PZMs are no longer available.  However. occasionally they'll appear on ebay.

The AKG C516 ML, which is the new replacement for the 416, has a different (and IMHO better) mounting system which may be easier fit onto the instrument:

http://www.akg.com/site/products/powerslave,id,981,pid,981,nodeid,2,_language,EN.html

j mobot

  • Member
  • *
  • Offline Offline
  • Posts: 11
  • Hohner Piccoletta Club I, Castagnari Dony
Re: Internal mics?
« Reply #2 on: June 16, 2008, 10:00:03 PM »

The capsules and circuits of PZM's are actually pretty simple and basic - its the "boundary mic" concept that was the clever bit. They used an omnidirectional capsule which is readily available from any Maplin, although most mic building articles on the internet advocate a specific Panasonic capsule. An omni pattern is good for this because it doesn't have a proximity effect and so doesn't have a hump in the bass response when used really close. The trade-off is that it feeds back more easily, but putting it inside the box obviously helps with that.

I've been using mics made to this design - http://www.prosoundweb.com/recording/tapeop/buildmic/buildmic_16_1.shtml - inside both ends and it works incredibly well. I also use a load of these for general recording including orchestral projects so I can vouch for the quality. The way I've fitted them was based on Nick Cookes boxes, which had mics fitted by Jeff Dando.

You can get the panasonic capsules in the UK from here - http://www.madaboutsound.com/prod_det.asp?cid=29&sa=cf&ctid=8.
Logged

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Internal mics?
« Reply #3 on: June 17, 2008, 11:43:53 AM »

Hmmm ...
If I remember rightly, the PZM's capsule is fitted facing up toward a solid, horizontal baffle only a mm or so above it.  This stops any sound from reaching the mic other than from the periphery, emphasising the bass or perhaps more correctly attenuating the top end.  The choice of the Panasonic capsule only offers improvement over even cheaper units by extending the frequency response down to 20Hz.  It would be interesting to mimic the PZM configuration inside the box and see if that noticeably influences the sound.

I could open up one of the centres of the "rose" soundholes and fix a capsule into it, looking straight into the soundbox from the lower end.  No, that would leave the wires dangling and a newish box deserves a neater solution.  Perhaps just fastening it inside and hooking it to a jackplug will do the trick.
Logged

j mobot

  • Member
  • *
  • Offline Offline
  • Posts: 11
  • Hohner Piccoletta Club I, Castagnari Dony
Re: Internal mics?
« Reply #4 on: June 17, 2008, 12:51:57 PM »

Quote
If I remember rightly, the PZM's capsule is fitted facing up toward a solid, horizontal baffle only a mm or so above it.  This stops any sound from reaching the mic other than from the periphery, emphasising the bass or perhaps more correctly attenuating the top end.

almost. The point is that reflected and direct sounds arrive in phase so interference is reduced and you get a higher pressure (and so stronger signal) in front of the capsule. Its not emphasising or attenuating anything though - more not colouring the signal so getting a truer bass. More here - http://www.soundonsound.com/sos/jan07/articles/qa0107_2.htm

I have thought about making a wooden version of the 'finger' that the capsule is mounted on. You'd just need to match the gap in front of the capsule and drill out a hole for it to be epoxyed into. It probably wouldn't take more than half an hour and a few hand tools.
Logged

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Internal mics?
« Reply #5 on: June 17, 2008, 02:49:52 PM »

If I'm correctly interpreting the article, the Tandy/Crown design mounts the mic looking back (closely) at the boundary, whilst others just mount the capsule with it flush to the boundary, looking out.  If that's right, then the simplest implementation might be to use the latter configuration with the mic simply set into the case!  If I'm really lucky, maybe I could achieve an interference fit of the capsule into a pre-existing hole - though I don't usually expect to be that lucky.
Logged

Waltham

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 198
Re: Internal mics?
« Reply #6 on: June 17, 2008, 08:12:55 PM »

I have thought about making a wooden version of the 'finger' that the capsule is mounted on. You'd just need to match the gap in front of the capsule and drill out a hole for it to be epoxyed into. It probably wouldn't take more than half an hour and a few hand tools.
We use thousands of the Panasonic electret capsules in my line of work.  Half the barrel of an old biro makes a good mounting for them.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal