Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: mengascini lever replacement  (Read 1743 times)

0 Members and 1 Guest are viewing this topic.

mellodeon

  • New Starter
  • Offline Offline
  • Posts: 3
mengascini lever replacement
« on: February 20, 2011, 01:53:06 PM »

i have a two row mengascini DG box on which the d button (3rd outer) had sheared off (it melted due to me simply playing too fast of course)

mr mengascini (he actually emailed me personally :)) says that he will send me a new lever but asks if i can fit it myself ok ( a reasonable question)

i have taken the covers of the box and revealed the inner levers frame.

i can see there is basically a spindle to which all the levers are ferruled onto ,that can it appears be pulled out by removing a coverplate on the side of the box

can i just pull (unscrew?) this spindle out or will the whole lot of levers just collapse into a pile of springs and twisted levers if i do.

it all looks relatively easy (naive perhaps )  but for not knowing if i should pull the spindle out and cause mayhem

my proposal is that i pull it out slowly at which point the levers will become loose of the spindle one by one and i collect the springs as they fall off , i think i then replace the levers by threading them back on again (reattaching the springs which i imagine is the hardest bit) including the new one from mr mengascini

any ideas  (taking it to some that knows what they are doing  being an obvious one )

thanks in advance

tim

Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: mengascini lever replacement
« Reply #1 on: February 20, 2011, 02:04:05 PM »

You have the right idea, but there are a couple of possible pitfalls.   First one is shifting the axle rod.  On a modern instrument its not usually a problem, but they can be initially quite tight.

Second, as you have worked out, as you withdraw the axle rod all the levers will become loose, and the pressure of the springs will make the livers pop out unless you stop them.  You need to be very controlled about pulling out the rod so you don't release several levers at the same time which then jump out and end up in a jumble
A strip of adhesive tape over the buttons can be helpful. 
Depending on the construction you might be able to unhook and withdraw the springs before pulling the axle rod.
All the levers must be kept in order so they go back in the same positions.  Numbering them can help.
The springs may not all be the same.  Often the springs for the outer row are made of thicker wire so they are slightly stronger.

Good luck.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mellodeon

  • New Starter
  • Offline Offline
  • Posts: 3
Re: mengascini lever replacement
« Reply #2 on: February 20, 2011, 02:12:00 PM »

thanks theo

i am going to wait for the  part to arrive and will do this calmly and switch my phone off when i have a few hours to spare with a pair of magnifying glasses on and some tweezers at the ready.

i am used to fixing things and have plenty of tools so i will try

i suppose the worst that can happen is i cant get the springs back or something i havent thought of yet

if it all  bellows  up in my face ! i can i suppose always give you a ring and put some work your way

thanks for the advice
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: mengascini lever replacement
« Reply #3 on: February 20, 2011, 02:27:56 PM »

I usually put an elastic band around the keyboard to stop the levers jumping out when the axle is withdrawn.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

mellodeon

  • New Starter
  • Offline Offline
  • Posts: 3
Re: mengascini lever replacement
« Reply #4 on: February 20, 2011, 05:34:44 PM »

thank you rees

i only have to take out 4 levers to get to button d (D) so i hope it will not prove to taxing

im going to wait for the part then try it

i have been playing it today with out any covers or buttons attached and it does make the most lovely clackering sound

thanks


tim

Logged

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: mengascini lever replacement
« Reply #5 on: February 20, 2011, 09:58:08 PM »

If there are distance pieces or -washers present, make sure that you put them back in the right order too. The washers, if there are any, are sometimes very thin and inconspicuous: try and locate them before you pull out the rod. When pulling out the rod a miniature chuck comes in handy.
« Last Edit: February 20, 2011, 10:04:47 PM by diatonix »
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal