Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: cutting my reed chamber  (Read 1712 times)

0 Members and 1 Guest are viewing this topic.

melod-ian

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 295
cutting my reed chamber
« on: February 23, 2011, 02:19:44 PM »

I've just got my order of reeds from CGM.. i need to cut the reed chamber out to fit these Italian reeds in (honer erica block)

before i make a complete hash of this.. whats the best place to start chiselling..

 
  • At the front.. where the sound hole is, to remove the lip that's there.
  • Or towards the back?

thanks
Logged
3 x Acadian's (C,Bb,A),
Hohner corona iiir (GCF)
PS Black Pearl (DG)
and the old hohner erica (DG)

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: cutting my reed chamber
« Reply #1 on: February 23, 2011, 02:23:46 PM »

I usually go for the top of the reed chamber, the top being the highest part you can see when the reedblocks are in place.   In extreme cases you can also file some aluminium off the rivet end of the reedplate.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

strad

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 418
Re: cutting my reed chamber
« Reply #2 on: February 23, 2011, 02:35:18 PM »

Photos of progress would be good.

Nigel
Logged

melod-ian

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 295
Re: cutting my reed chamber
« Reply #3 on: February 23, 2011, 03:01:54 PM »

thanks theo.  so cutting that bottom lip isn't an option no?
Logged
3 x Acadian's (C,Bb,A),
Hohner corona iiir (GCF)
PS Black Pearl (DG)
and the old hohner erica (DG)

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: cutting my reed chamber
« Reply #4 on: February 23, 2011, 03:27:06 PM »

I found when doing the same job that there was plenty of "meat" in the top of the reed block to carve it out to match the reed plate. I used a standard scalpel to do the job.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: cutting my reed chamber
« Reply #5 on: February 23, 2011, 04:47:39 PM »

The bottom plate on Hohner blocks is not terribly thick or strong,  indeed check your blocks especially the longer one at the opposite end from the screw clamp - the base often breaks away there and needs to be re-glued.

I prefer a chisel for enlarging the top,  but it must be very sharp.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: cutting my reed chamber
« Reply #6 on: February 23, 2011, 05:32:49 PM »

I also like cutting the top of the chamber with a sharp chisel when enlarging.  The bottom  is usually thin, and besides the reasons already mentioned, I also like a little ledge on the bottom for waxing when possible. Sometimes on lay down blocks for the lower reeds, the upper end is right up against the frame, so you're either stuck with cutting into the frame, or if it's just a little, I'll inlet the bottom a little.

melod-ian

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 295
Re: cutting my reed chamber
« Reply #7 on: February 23, 2011, 08:44:24 PM »

Thanks for the good advise already i have a nicer sounding Erica and I'm only half way through (:)
Logged
3 x Acadian's (C,Bb,A),
Hohner corona iiir (GCF)
PS Black Pearl (DG)
and the old hohner erica (DG)
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal