Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: How was presswood manufactured?  (Read 7487 times)

0 Members and 1 Guest are viewing this topic.

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
How was presswood manufactured?
« on: March 04, 2011, 09:37:30 PM »

I keep having bouts of MAD as I peruse Fleabay and see the beautiful old boxes made with the presswood technique. Hohner, Koch, Beaver, La Strada. Most have the same presswood decorations, probably coming from molds and common techniques in the years  before and after Hohner acquired a company, for example Koch. However, the decorative technique does seem to be common to German instruments in the early 20th century and not particular to Hohner. There are Koch instruments with this type of decoration the appear to predate Hohner's acquisition of Koch.

I've been reading and searching on the internet for some clues to this decorative technique and don't find anything. It's not a woodworking technique that seems to be practiced anymore except as an art form consisting of a burnt wood technique that bears little resemblance to the production technique that the manufacturers used. I've looked in the melnet archives and find very little there, guesses only, some of which correspond to my own musings.

I've twice tried contacting the Hohner company on the US side but it's been more than a month with no response. Does anyone have a contact in the Hohner repair department to whom I could write? What I really need is a Hohner historian, someone who has been around for a long time and knows who the original craftsmen were or where molds are. Most of the craftsmen are probably dead and gone, but some might still be around, at least I hope so and I'm crossing my fingers on finding molds.

I don't know the history of the presswood decoration used by Hohner and that might help. Does anyone know the last year that Hohner sold instruments with presswood decoration? For that matter, when did presswood decoration as a manufacturing technique first show up on musical instruments?
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

OldDog

  • Good talker
  • **
  • Offline Offline
  • Posts: 89
Re: How was presswood manufactured?
« Reply #1 on: March 04, 2011, 11:45:35 PM »

Hi,

Try here, someone should be able to help you:

FN:Director Martin Haeffner
N:Haeffner;Martin;;Director;
X-SALUTATION:Director
ORG:German Harmonica Museum
TITLE:Directors
ADR;TYPE=WORK:;;Deutsches Harmonikamuseum /German Harmonica and Accordion MuseumLöwenstr. 1178647 TrossingenTelephone 0049 74 25 / 2 16 23Telefax 0049 74 25 / 82 89E-Mail harmonika-museum@t-online.dewww.harmonika-museum.de;;;;
Logged
Over the hill? What hill?! I didn't see no hill!

Christopher K.

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 894
Re: How was presswood manufactured?
« Reply #2 on: March 05, 2011, 02:48:19 AM »

I would love a definitive explanation of the process.... there were a few different variations of it. Each time I see one it seems different: lighter, darker, deeper, shallower, etc.

The Koch accordions you['re referring to are the A.S. Koch wooden two-rows with the schutzmark mountain goat and mountain scene on the cabinet? The first two photos have more than just a few similarities with Hohner presswood models: motif, grille, keyboard. I have noticed a difference in dimensions and shape between the keyboards on some Hohner Presswood Pokerworks and Hohner Pokerworks and celluloid covered Vienna models - while many Presswood Pokerworks share their keyboard dimensions with the Koch models.

Photo on the bottom is an accordion built by Koch and sold by Montgomery Ward (it has Koch reeds inside).

FWIW Hohner used a lot of ideas originating from the Koch company. Some "new" Hohner models from the period right before and right after the takeover of Koch are exact copies, with scaled back details. I think Hohner also learned a lot about piano accordions from Koch. This pattern holds with the other companies Hohner absorbed - it is very economical and is part of my fascination with the company.
« Last Edit: March 05, 2011, 03:04:56 AM by Christopher K. »
Logged

Christopher K.

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 894
Re: How was presswood manufactured?
« Reply #3 on: March 05, 2011, 02:51:06 AM »

I've twice tried contacting the Hohner company on the US side but it's been more than a month with no response. Does anyone have a contact in the Hohner repair department to whom I could write? What I really need is a Hohner historian, someone who has been around for a long time and knows who the original craftsmen were or where molds are. Most of the craftsmen are probably dead and gone, but some might still be around, at least I hope so and I'm crossing my fingers on finding molds.

I'm not sure such an individual exists - it was my understanding the Hohner people in Germany don't know much more than we about who made the instruments and what the original processes were? I thought most of the documentation was lost.

Maybe Tim Schofield could set us straight on who to ask?

Graham W

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 277
Re: How was presswood manufactured?
« Reply #4 on: March 05, 2011, 09:44:05 AM »

I would imagine that the wood would have been steamed to give it some plasticity and then,  well,  pressed with a suitably formed press tool.  I guess it would have been left under pressure for some time until the wood dried and took a permanent relief without warping.

The variations in depth and colour suggests that the press was fairly simple and hand operated, and possibly the tool was heated in some way to speed the process up.

Just an educated guess . . .   (:)
Logged

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: How was presswood manufactured?
« Reply #5 on: March 05, 2011, 06:15:49 PM »

Graham,

Your guesses are similar to mine. I have a feeling that one side of the boards were either steamed or floated in hot water to force absorption of water and make one surface more pliable. Yes, there might be some cupping or bowing of the wood for a bit, but the process would have been, I think, fairly quick.

After hydrating one side (or both) of the piece of wood, I suspect the wood was passed through a heated roller press. The wood would sit on a flat platten that moves slowly. I think the design would have been cut, molded, or otherwise placed into the surface of a cylinder. This cylinder would then roll over the wood, pressing the design into the surface of the damp wood. Then the wood piece goes off to dry. If the cylinder were heated in some fashion, so much the better. A cylinder arrangement would have placed more pressure at the point of contact, allowing for less overall pressure and a simpler press than a system where the whole piece of wood went into a flat press.

The instruments I've seen and, indeed, my own instrument, show signs of variations in the amount of heat or browning of the pressed surface. Some of the decorations look like they've been heated hotter in one area than another, almost as if the fellow heating the surface of the cylinder wasn't paying attention for a moment and overheated the surface.

Given the kinds of detailing I've seen on the different instruments (thanks for the different photos!) I suspect there was a mold of some kind, fairly easily made. Or perhaps it was a sheet of some kind of metal - cast iron - that was engraved or carved with the patterns needed.

Some of the ease or difficulty of this process would depend on the type of wood used. The Presswood Pokerwork I have looks like it's made from maple/sycamore though I don't have any way to test it. A softer hardwood would make more sense really - Alder?

My current thoughts on this process. I hope to find out something more definitive.
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: How was presswood manufactured?
« Reply #6 on: March 05, 2011, 08:27:08 PM »

Given the number of manual and power driven blanking presses in rows illustrated in some of the early workshop pictures in the Hohner history books and as cylinder presses were still in ongoing deveopment purely for printing during this period I think a platten type press is more likely, perhaps with a steam heated platten.

My early one row is very much Koch in style and might be old enough to be a badged Koch, the bass end cover (treble end was missing) has clearly had all the holes punched rather than drilled or fretted and looking at the bunching of the grain and tear at breakthrough I think all holes went in at one hit - this doesn't have presswork decoration.

Might even have been  hot pressed after laquering (but before full drying) to get the caramelised effect on the lowlights ??

I like the Koch idea of having an aduster for each bellows to endbox hook pivot to ensure that the seal can be maintained as the box wears - no doubt value engineered out by the Gebrs. Hohner.............

Richard
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

Christopher K.

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 894
Re: How was presswood manufactured?
« Reply #7 on: March 05, 2011, 08:58:04 PM »

More miscellanea: the pattern on the Concertone keyboard cover (circa 1924 from paperwork that came with the box) is totally flat, not textured like the rest of the accordion, and the variable shading in that area is also different. It looks as if for whatever reason, the keyboard cover was finished with a different process and by hand - maybe a template and an open torch? Later Presswood Pokerworks from Koch and Hohner, which incorporate the leaf motif on the edge of the keyboard, are decidedly textured and there is less variation in the shading, as if by a machine press.

I'll try to snap a photo on Sunday.

Quote
Might even have been  hot pressed after laquering (but before full drying) to get the caramelised effect on the lowlights ??

I've wondered if the press was done after it was lacquered, too. It explains easily how the pressed areas are darker. Can lacquer behave that way?
« Last Edit: March 05, 2011, 09:01:15 PM by Christopher K. »
Logged

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: How was presswood manufactured?
« Reply #8 on: March 05, 2011, 10:08:13 PM »

I'll see if I can find something suitably laquered to torture with a soldering - iron if no one else comes up with a yea or neigh ;)

Richard - been torturing a 2m ex ebay radio transceiver most of the day so a warm iron is no problem
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

oggiesnr

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 995
  • Dino BPII, Alfred Arnold Bandoneon, Loffet G/C
Re: How was presswood manufactured?
« Reply #9 on: March 05, 2011, 10:23:07 PM »

I'd always assumed that the design was on pressed with a heated plate and a steam or hydraulic press which can generate huge amounts of even pressure over a large area.  Even a manual "nipping" press could crush your hand and I used to cut out 12 inch circles of 4mm birch with a small (50 ton) power press.

Very fast and very repeatable.

I'm not sure a roller would work because the image would not be presented flat and you would need two power sources, one to press the rollers and a second to rotate them.  Seems a complicated solution compared to a flat stamping process.

Steve
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: How was presswood manufactured?
« Reply #10 on: March 05, 2011, 10:26:56 PM »

I'm not sure a roller would work

And you could get distortion and bending of the wood as it went through a tight nip like that
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: How was presswood manufactured?
« Reply #11 on: March 05, 2011, 11:09:02 PM »

You're probably right about flat pressing vs. roller.

I'm liking this discussion. It never occurred to me that laquer might burn or darken and cause the darker lower surface. Interesting idea.

I'd like to give this a try sometime soon. I have a nipping press that can generate quite a bit of pressure. I've used it for book binding and veneering in the past.

So what kind of mold was used that could be heated and used in a press? Cast iron? How were the designs carved out of the mold, or was the mold/pattern cast in some way on top of a design? I suppose you could do a lost wax technique with the right kind of metal? The metal pattern piece wouldn't need to be very thick, really since the relief in the wood comes to about .2 - .3 mm or so, at least on my Pokerwork.

Great discussion!

Ed
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: How was presswood manufactured?
« Reply #12 on: February 27, 2014, 08:31:13 PM »

I recently found a series of videos around the now preserved and wholly steam powered Phillips Bros Sawmill & Box Factory in the good old US of A, which in terms of process and machinery would be pretty indicative of how some of our boxes may well have been made. If you look at this one, about 7 mins in shows how machine 'pokerwork' or more accurately plate scorching is undertaken and probably answers this long slumbering thread as well as its ever likely to be.

http://www.youtube.com/watch?v=_mKSKZau9qs&list=PL91D812D3A6AB9D8A

For those who appreciate old technology the other dozen or so videos bythis chap at the mill are well worth watching as Hohners would have bought their timber by the stick and reduced it from trunks (5 foot diameter stick in the one entitled Ponderosa Pine !) through planks, to boards, planed them cut them to length etc and the variety of rip and cross cutting saws are well represented, the corner / edge nailing / stapling machines do not seem to have been much used in melodeons but their despatch cases would.

Sorry for reviving an old thread, I'm sort of missing thread drift..............
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

Malcolm Austen

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 495
  • any old hohner
Re: How was presswood manufactured?
« Reply #13 on: February 28, 2014, 09:34:45 AM »

For a one off project you could use laser wood engraving, there are shops that will do small cutting and engraving jobs. This is also a good way to cut complex grill patterns, I will post a picture of my effort asap.
Logged
aka malodeon

pikey

  • Addicted to squeezeboxes since 1975
  • Thread mod
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3364
  • If it moves, I'll squeeze it....
Re: How was presswood manufactured?
« Reply #14 on: February 28, 2014, 09:39:08 AM »

Brilliant clip.
Logged
Still squeezing after all these years.
Mostly on hohners , with a couple of Dinos and a smattering of anglos - and now a Jeffries duet

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: How was presswood manufactured?
« Reply #15 on: February 28, 2014, 09:44:45 AM »

I think the finish and feel mean so much. A box is a very tactile thing. It is the only thing for me that spoils the Albrecht. It's varnished (very well I must add) but an oiled finish or polish to my mind would have been much better. I suppose each to his own if you get my drift.  ???
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

Malcolm Austen

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 495
  • any old hohner
Re: How was presswood manufactured?
« Reply #16 on: February 28, 2014, 10:18:05 AM »

Engraved and cut examples
Logged
aka malodeon

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: How was presswood manufactured?
« Reply #17 on: February 28, 2014, 10:31:21 AM »

In reference to the youtube link posted by BB: I'm certainly no workplace safety freak myself (as I sometimes wish I were), but watching these people without hearing protection, goggles or dust masks makes even someone like me feel uncomfortable. Not to mention the more than shoulder long unrestrained hair...

@ Malcolm: It would be even nicer if the engraved areas were filled with a different type of wood. It is easily done, using essentially the same program in vector mode.
« Last Edit: February 28, 2014, 10:42:16 AM by diatonix »
Logged

Malcolm Austen

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 495
  • any old hohner
Re: How was presswood manufactured?
« Reply #18 on: February 28, 2014, 11:02:30 AM »


@ Malcolm: It would be even nicer if the engraved areas were filled with a different type of wood. It is easily done, using essentially the same program in vector mode.
[/quote]

diatonix
You are quite right but this being my first effort and a lack of time resulted in a simple design.
malcolm
Logged
aka malodeon

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: How was presswood manufactured?
« Reply #19 on: February 28, 2014, 01:07:42 PM »

In reference to the youtube link posted by BB: I'm certainly no workplace safety freak myself (as I sometimes wish I were), but watching these people without hearing protection, goggles or dust masks makes even someone like me feel uncomfortable. Not to mention the more than shoulder long unrestrained hair...

@ Malcolm: It would be even nicer if the engraved areas were filled with a different type of wood. It is easily done, using essentially the same program in vector mode.

I hear diatonix - this was a family built and run plant and is now family trust run so employees have not been an issue AFAIK, re safety, hearing protection is in use in the box plant (but easily missed) as is dust / chip extraction, neither would currently stand scrutiny in the UK, yet despite this none of the participants have been killed or mutilated, other than the external belt drives, the adaption and construction of the equipment show clear signs of reducing access to dangerous parts and reducing injurious repetitive actions, I can see pre and possibly post WW2 Hohner boxes being produced under very similar conditions.

The modern methods of producing complex components have so far covered gnawing parts out of raw material but we already have nearly 'affordable' means of 3D writing much of the required componentry for our tailored, customised Costalotti at home  (:) with the possibility of writing a complete* working box perhaps not too far into the future !

Economic? - I doubt it

Hand and eye feel? - probably no good

Sound quality? - probably appalling

Should the Wessons, Loffetts & other quality makers be worried? - Nope (but might be handy for recreating bits of old boxes for repair)

Will it happen? - I'd be surprised if some components aren't being produced within the next 5 years

Who will write the first melodeon? - Quite probably someone on the forum  ;D

* can't quite see the route to bellows yet, or reed hardness for that matter

Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal