Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Pallet Shape discussion  (Read 1941 times)

0 Members and 1 Guest are viewing this topic.

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Pallet Shape discussion
« on: March 18, 2011, 06:39:57 PM »

I've been looking at the various pallet designs for both treble and bass, and the surfaces that they bed against. Haven't found a discussion of the shape of the pallets yet though I have seen discussions of the size and shape of the hole in the fondo. If there is a discussion pertaining to my observations and questions below, please point me to that discussion.

I've put together a photo of different types of pallet/fondo designs that you can see below.

1. Is from a Tommy Bass section (thanks Lester) It shows wooden pallets faced with felt and leather and bedding on a metal plate.
2. From a Saltarelle Tramontane bass section that Theo did beautiful job of restoring and photographing. The wooden pallets are faced with felt and leather and bed against a wood fondo.
3. From a Hohner Corso rebuild. Typical Hohner wood pallets, felt and leather pads but with the addition of a leather bedding surface glued to the fondo.
4. From a La Tosca of unknown age, Metal pallets with leather pads (yes the pads need replacing). These provide, essentially a cupped surface for the felt/leather to bed against the wood fondo (at least that's what it looks like to me).

I have some questions for the players and makers on the list.

Which kind of pallet design provides a better seal for both push and pull?
1. The flat faced pallet (1,2,3) that forces a portion of the leather into the hole in the fondo?
2. The cupped version (4) that creates a seal around the edges of the pallet rather than around the edges of the hole?
3. Flat pallet against wood.
4  Flat pallet against metal.
5. Flat pallet against leather on wood.

Related discussion is the relative silence of each of these pallet designs.

Does the design of the pallet make much of a difference to the sound of the pallet as it hits the fondo? Hohners are famous for their clacking or slapping sound as the pallets hit the fondo and use the flat wood pallet against a wooden fondo with round holes in the fondo. Some like that distinctive sound of the pallet, others don't. It would be good to know the kind of pallet design that causes this kind of sound, or the mechanics coupled with the pallet design.

Is the silence or noise of the pallets more a result of the mechanical setup than the design of the pallets?

These are by no means the only designs currently in use, add photos of others you think work well or badly and talk about their features.

Ed
« Last Edit: March 18, 2011, 06:43:47 PM by Telemorris »
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Christopher K.

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 894
Re: Pallet Shape discussion
« Reply #1 on: March 19, 2011, 06:22:44 PM »

#4 is interesting - you say it came out of a La Tosca badged machine. I have a Koch with those same pallets, which I've found to be a real pain to resurface and I don't think they provide adequate pressure against the holes. The springs are very strong but there seems to be pressure exerted upwards along the length of the lever arm, creating a sheering between the pallet and board, instead of pushing the pallet dead onto the soundhole. You can see the top of the pallet beds deeper on the top edge than the bottom. Plus it is far easier to adjust (read: bend and mess up) the position of the pallet relative to the hole and lever by bending the pallet from where it is soldered to the lever. This is probably what's happening over time under the heavy spring pressure so I don't think it's a terrific design.

This may solve part of the La Tosca manufacturing mystery, too.

(edit : FWIW, my two La Toscas had clunky wooden pallets.)
« Last Edit: March 19, 2011, 06:26:43 PM by Christopher K. »
Logged

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Pallet Shape discussion
« Reply #2 on: March 19, 2011, 08:27:24 PM »

This is the La Tosca I took the pallet photo from.

I've seen this pallet design before and hesitated at a purchase because I wondered how well this design seals the holes. Glad to hear about your problems with the design.
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Pallet Shape discussion
« Reply #3 on: March 19, 2011, 08:32:38 PM »

The springs are very strong but there seems to be pressure exerted upwards along the length of the lever arm, creating a sheering between the pallet and board,

And The Shearing's Not For You, eh.....? :D
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal