Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Fitting bellows tape up against bellows frames  (Read 2491 times)

0 Members and 1 Guest are viewing this topic.

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Fitting bellows tape up against bellows frames
« on: March 28, 2011, 06:30:17 AM »

Hi all
Just re-taping the bellows on my old Hohner Club. It's all going very well, but is there a trick to taping the very end folds where the bellows are glued to the frames?  If I have to remove the frames, what's the safest technique?

Cheers
Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Fitting bellows tape up against bellows frames
« Reply #1 on: March 28, 2011, 10:00:45 AM »

If you feel comfortable regluing the frames to the bellows, I'd recommend removing them before re-taping. Usually, Hohner frames are not difficult to remove. I use a blunt screwdriver, and start from the inside in order not to leave ugly traces on the frames. Do it gently and try and leave the cardboard as intact as possible, especially at the corners.  Before putting them back in place you should cut away some of the tape covered by the frames, as the glue doesn't stick well to it.
Logged

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Fitting bellows tape up against bellows frames
« Reply #2 on: March 28, 2011, 02:55:09 PM »

If you feel comfortable regluing the frames to the bellows, I'd recommend removing them before re-taping. Usually, Hohner frames are not difficult to remove. I use a blunt screwdriver, and start from the inside in order not to leave ugly traces on the frames. Do it gently and try and leave the cardboard as intact as possible, especially at the corners.  Before putting them back in place you should cut away some of the tape covered by the frames, as the glue doesn't stick well to it.

Thanks - I'll probably give that a try.

Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Fitting bellows tape up against bellows frames
« Reply #3 on: March 29, 2011, 04:45:13 PM »

Well, I decided the only workmanlike thing to do was remove the frames, which turned out to be far less traumatic than I had feared.  End folds now duly re-taped, frames re-installed and currently in the workshop drying out under moderate pressure.  Good job done - thanks for the advice.

Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

bonenfant

  • Good talker
  • **
  • Offline Offline
  • Posts: 71
Re: Fitting bellows tape up against bellows frames
« Reply #4 on: November 14, 2011, 12:41:06 AM »

I just talked to an accordion repairman and...... removing the frame is not a good idea. It's very hard on the cardboard even with all the taking care in the world. You can replace bellows tape without removing the bellows from the accordion. When you know hows it's done, it's not so hard.
Logged

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: Fitting bellows tape up against bellows frames
« Reply #5 on: November 14, 2011, 02:35:57 AM »

I just talked to an accordion repairman and................When you know hows it's done, it's not so hard.

Would you care to elaborate on that statement? ???
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Fitting bellows tape up against bellows frames
« Reply #6 on: November 14, 2011, 07:06:27 PM »

Just run a blunt knife between bellows and frame to the depth of the old tape,  remove the old tape.  The new tape should be slightly narrower than the full width used on the other folds.  Lay some glue into the gap, glue the tape in the normal way and insert the tape into the gap. Fold the tape down on the side away from the frame and clean up surplus glue with a damp cloth.

Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: Fitting bellows tape up against bellows frames
« Reply #7 on: November 14, 2011, 07:17:01 PM »

Thanks Theo!  ;)
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal