Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Pokerwork refurbish - Result of re-felting pads  (Read 3008 times)

0 Members and 1 Guest are viewing this topic.

brianread

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1012
    • Slow and Steady Session in West Lancashire/Greater Manchester; Dance club in Rainford
Pokerwork refurbish - Result of re-felting pads
« on: April 04, 2011, 12:51:08 PM »

Ok, I've used some of charlie's dual layer felt to re-felt the pads on my pokerwork, but am now concerned about the resultant reduction in height the keys stick out from the keyboard.  I intend to use Theo's method of reducing the travel but I suspect that I need to recover some of the height I've lost by increasing the thickness of the felt/leather.  Two possiblities I can see:

1. Bend the metal on each key - danger of breaking it?
2. Cut the slot in the pad deeper so that the metal arm goes in further.

any thoughts?
Logged
Brian Read
D/G Oakwood (new model), D/G, C /F, Bb/Eb and E/A Liliputs,
A STREB!!,
2.5 D/G Self made Emmanuel Pariselle, D/G Pokerwork,
and Wolverton Advanced G/D Anglo Concertina and C/G  1937 Wheatstone.
all played "lefty" with mostly an extra air button, except the Concertinas which I play the conventional way round.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Pokerwork refurbish - Result of re-felting pads
« Reply #1 on: April 04, 2011, 01:31:04 PM »

Bend the levers. Just pull up on the pallet lever till the button is at its lowest, then give a further gentle pull.  An improvised hook is helpful for lifting the lever.    If you go too far then hold down the pallet while pushing the button down.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

brianread

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1012
    • Slow and Steady Session in West Lancashire/Greater Manchester; Dance club in Rainford
Re: Pokerwork refurbish - Result of re-felting pads
« Reply #2 on: April 04, 2011, 02:04:26 PM »

Bend the levers. Just pull up on the pallet lever till the button is at its lowest, then give a further gentle pull.  An improvised hook is helpful for lifting the lever.    If you go too far then hold down the pallet while pushing the button down.

excellent - thanks.
Logged
Brian Read
D/G Oakwood (new model), D/G, C /F, Bb/Eb and E/A Liliputs,
A STREB!!,
2.5 D/G Self made Emmanuel Pariselle, D/G Pokerwork,
and Wolverton Advanced G/D Anglo Concertina and C/G  1937 Wheatstone.
all played "lefty" with mostly an extra air button, except the Concertinas which I play the conventional way round.

Martyn

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 455
  • Hohnerohner
    • Martyn White Melodeon Tuning and Repairs
Re: Pokerwork refurbish - Result of re-felting pads
« Reply #3 on: April 05, 2011, 11:20:14 AM »

Bend the levers. Just pull up on the pallet lever till the button is at its lowest, then give a further gentle pull.  An improvised hook is helpful for lifting the lever.    If you go too far then hold down the pallet while pushing the button down.

Although it takes a little longer, I find it best to set the button height before glueing the pallets. Bending the levers after the pallets have been fixed can change their angle and cause them not to seat properly.
I position the pallets on the levers, adjust button height then fix the pallets using the traditional method of glueing a 10mm dot of linen over the lever to hold the pallet in place.

Martyn
www.melodeonrepairs.co.uk

Edited to add 10mm dot of linen.
 
« Last Edit: April 05, 2011, 01:50:33 PM by martyn »
Logged
'Anything from a small repair to a full restoration'.
www.melodeonrepairs.co.uk

brianread

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1012
    • Slow and Steady Session in West Lancashire/Greater Manchester; Dance club in Rainford
Re: Pokerwork refurbish - Result of re-felting pads
« Reply #4 on: April 05, 2011, 12:06:22 PM »

Bend the levers. Just pull up on the pallet lever till the button is at its lowest, then give a further gentle pull.  An improvised hook is helpful for lifting the lever.    If you go too far then hold down the pallet while pushing the button down.

Although it takes a little longer, I find it best to set the button height before glueing the pallets. Bending the levers after the pallets have been fixed can change their angle and cause them not to seat properly.
I position the pallets on the levers, adjust button height then fix the pallets using the traditional method of glueing a 8mm dot of linen over the lever to hold the pallet in place.

Martyn
www.melodeonrepairs.co.uk

Thanks Martyn, actually that is exactly what I am doing, although I could not have explained exactly why I thought it was best!
Logged
Brian Read
D/G Oakwood (new model), D/G, C /F, Bb/Eb and E/A Liliputs,
A STREB!!,
2.5 D/G Self made Emmanuel Pariselle, D/G Pokerwork,
and Wolverton Advanced G/D Anglo Concertina and C/G  1937 Wheatstone.
all played "lefty" with mostly an extra air button, except the Concertinas which I play the conventional way round.

waltzman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 943
Re: Pokerwork refurbish - Result of re-felting pads
« Reply #5 on: April 05, 2011, 02:33:35 PM »

Bend the levers. Just pull up on the pallet lever till the button is at its lowest, then give a further gentle pull.  An improvised hook is helpful for lifting the lever.    If you go too far then hold down the pallet while pushing the button down.

Although it takes a little longer, I find it best to set the button height before glueing the pallets. Bending the levers after the pallets have been fixed can change their angle and cause them not to seat properly.
I position the pallets on the levers, adjust button height then fix the pallets using the traditional method of glueing a 10mm dot of linen over the lever to hold the pallet in place.

Martyn
www.melodeonrepairs.co.uk

Edited to add 10mm dot of linen.
 


Hide glue?
Logged

Martyn

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 455
  • Hohnerohner
    • Martyn White Melodeon Tuning and Repairs
Re: Pokerwork refurbish - Result of re-felting pads
« Reply #6 on: April 05, 2011, 07:26:36 PM »

Bend the levers. Just pull up on the pallet lever till the button is at its lowest, then give a further gentle pull.  An improvised hook is helpful for lifting the lever.    If you go too far then hold down the pallet while pushing the button down.

Although it takes a little longer, I find it best to set the button height before glueing the pallets. Bending the levers after the pallets have been fixed can change their angle and cause them not to seat properly.
I position the pallets on the levers, adjust button height then fix the pallets using the traditional method of glueing a 10mm dot of linen over the lever to hold the pallet in place.

Martyn
www.melodeonrepairs.co.uk

Edited to add 10mm dot of linen.
 


Hide glue?


No, I tend to use pva. It saves keeping the glue pot going.  ;)

Martyn
www.melodeonrepairs.co.uk
Logged
'Anything from a small repair to a full restoration'.
www.melodeonrepairs.co.uk

brianread

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1012
    • Slow and Steady Session in West Lancashire/Greater Manchester; Dance club in Rainford
Re: Pokerwork refurbish - Result of re-felting pads
« Reply #7 on: April 30, 2011, 07:52:46 PM »

Have now re-felted the bass end as well, and got rid of some of the clatter, but  I can see that the buttons still move inside the holes in the case, and therefore I presume I ought to felt line the holes as well.

Anyone got any pointers for this job?
Logged
Brian Read
D/G Oakwood (new model), D/G, C /F, Bb/Eb and E/A Liliputs,
A STREB!!,
2.5 D/G Self made Emmanuel Pariselle, D/G Pokerwork,
and Wolverton Advanced G/D Anglo Concertina and C/G  1937 Wheatstone.
all played "lefty" with mostly an extra air button, except the Concertinas which I play the conventional way round.

brianread

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1012
    • Slow and Steady Session in West Lancashire/Greater Manchester; Dance club in Rainford
Re: Pokerwork refurbish - Result of re-felting pads
« Reply #8 on: May 09, 2011, 02:35:58 PM »

Have now re-felted the bass end as well, and got rid of some of the clatter, but  I can see that the buttons still move inside the holes in the case, and therefore I presume I ought to felt line the holes as well.

Anyone got any pointers for this job?

aha - I see that this is called (by Theo) re-bushing (I think).  What felt should I use?
Logged
Brian Read
D/G Oakwood (new model), D/G, C /F, Bb/Eb and E/A Liliputs,
A STREB!!,
2.5 D/G Self made Emmanuel Pariselle, D/G Pokerwork,
and Wolverton Advanced G/D Anglo Concertina and C/G  1937 Wheatstone.
all played "lefty" with mostly an extra air button, except the Concertinas which I play the conventional way round.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Pokerwork refurbish - Result of re-felting pads
« Reply #9 on: May 09, 2011, 02:47:19 PM »

Bushing cloth!

Its a woven material with a felted surface, as used in pianos and concertinas.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal