Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Reed block and sound board materials  (Read 13241 times)

0 Members and 1 Guest are viewing this topic.

Jon Loomes

  • Performer, Recording Engineer, Luthier.
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 115
  • Non plaudite. Pecuniam jacite.
    • www.jonloomes.com
Reed block and sound board materials
« on: July 17, 2008, 02:58:42 PM »

Hello all - Time for me to pick your brains....


Can anyone tell me what effect on tone different materials have when used for:

Reedblocks
Soundboards
etc?

Reason I'm asking is, I played an Oakwood model 7 the other day - incredible sound. Sure, I know it's Binci reeded, but I'm guessing there's more to it than that.

So, starting with good reeds, the next component is the block, then the board etc etc if you see my logic? or am I completely wrong here?

Has anyone had an Oakwood to pieces to see why they work so well? Any thoughts?


Cheers,
Jon

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Reed block and sound board materials
« Reply #1 on: July 17, 2008, 03:55:10 PM »

Hello Jon,

Aren't you the Jon Loomes that made the youtube videos for the Music Room? If so, why don't you give Martyn a call and ask him? I've known Martyn for many years and he always seemed very free with his knowledge. I was doing a bit of work for Oakwood when the melodeons were being developed but I didn't take much notice at the time. Martyn even asked me if I'd like to learn how to tune accordions but it didn't interest me at all back then so I declined.  :o

If I was back up in Leeds now I'd be on his case to get production going again but as far as I'm aware there are no plans to do so in the forseeable future.

Pete.
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Waltham

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 198
Re: Reed block and sound board materials
« Reply #2 on: July 17, 2008, 04:08:25 PM »

I don't believe we yet properly understand how the material properties of the reedblock, soundboard etc affect the sound.  There have been some very interesting investigations (see the thread on foam melodeons) but we're still far short of a comprehensive theory.  And for almost every rule-of-thumb or general principle it's possible to find a counterexample, while two identical looking instruments can sound quite different.  I've not looked inside an Oakwood but I've looked inside lots of other models and it hasn't told me why they sound they do (apart from the obviously knackered ones) any more than looking inside a Stradivarius would tell you why it sounds so good.

Logged

Bill Young

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1151
  • Paolo Soprani BCC#
Re: Reed block and sound board materials
« Reply #3 on: July 17, 2008, 04:52:54 PM »

This subject has been talked to death, yet again, over on rec.music.makers.squeezebox (68 posts over a couple of months). If you fancy relief from the excitement of watching paint dry, you can start following the whole thread HERE.
Logged

Jon Loomes

  • Performer, Recording Engineer, Luthier.
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 115
  • Non plaudite. Pecuniam jacite.
    • www.jonloomes.com
Re: Reed block and sound board materials
« Reply #4 on: July 17, 2008, 08:39:00 PM »

Bill - Thanks for the link - I'll check with interest,
Pete -  yes I'm afraid I am the fat lad in the MR videos. (It's the pills...or at least, one of the side effects, I've not been well you know...) I'll ask Martyn when I see him but he's not round that much.
Waltham - Having just finished building a Guarneri copy, I've got a pretty shrewd idea why the physical nature of a  Strad. et al makes a good instrument. I quite agree though - 2 identical Castagnaris can be quite different. Boxes are weird and I suspect rather different rules apply. As the americans say.."Go figure".

Many thanks to all for your contributions - It's great that there's somewhere on the net where people don't always talk a load of hot air.

Cheers,
Jon

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Reed block and sound board materials
« Reply #5 on: July 17, 2008, 10:04:19 PM »

Hello all - Time for me to pick your brains....


Can anyone tell me what effect on tone different materials have when used for:

Reedblocks
Soundboards
etc?

Reason I'm asking is, I played an Oakwood model 7 the other day - incredible sound. Sure, I know it's Binci reeded, but I'm guessing there's more to it than that.

So, starting with good reeds, the next component is the block, then the board etc etc if you see my logic? or am I completely wrong here?

Has anyone had an Oakwood to pieces to see why they work so well? Any thoughts?


Cheers,
Jon

I've not only had one to pieces, I made several design changes to the one that Oakwood built for me (which was the first Model 4) to improve some of the design weaknesses -- very clean, clear and loud, very responsive. Some of the things that probably help (at least in mine) are:

-- exceptionally large rectangular air holes under the pallets (almost the same area as the reed block cavities)
-- thin aircraft ply "soundboard"
-- pallets which lift up quite a long way to clear the holes
-- tapered reed blocks to reduce the air volume for the high reeds -- the reed mounting faces are actually curved inwards
-- very open grille standing up from the soundboard (no deep cavity with the pallets inside)
-- Salpa reeds -- Martyn reckoned at the time that these had more "bite" than Antonelli or Binci
-- bigger bass reed blocks (dimensions taken from my Castagnari Dony) with three bass reeds on the note as well as the chord
-- tuned by Nils Nielsen -- always a good thing!

Other changes I made were mainly to improve the ergonomics (very important!) rather than the sound.

Cheers

Ian
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Reed block and sound board materials
« Reply #6 on: July 17, 2008, 11:05:01 PM »

The reed-blocks in my accordions are as follows:

Various Hohners - softwood, waxed.
Castagnari Sander 1989  - softwood, D/G waxed.
Dino Baffetti Carnival III  - softwood, A/D waxed.
Marc Savoy Bb - maple wood, originally in C waxed, now B-flat screwed on leather.
Wesson No.1  (the one I made on the EATMT course last year) cherry wood, C screwed on leather.
Wesson No.2 (the one I made when I got back from the course) - tulip wood, D screwed on leather.

A reed block maker in Castelfidardo advised me that alder is the best wood for reed-plates screwed on leather.
Anyone got a nice piece of alder I could scrounge?

I have two instruments currently under construction. The customers have both specified maple wood throughout so the blocks will be of maple. I like using maple as it hold the screws well. The wood is maple flooring offcuts kindly donated by our friend Simon W via FreeCycle. (It's looking gorgeous Simon).
I may use walnut or afrormosia pallets just to break up the whiteness of the maple. (that OK Simon?).

BTW, for the sound-board or fondo (good name) as the Italians call it. I use two sheets of 1.5mm aircraft ply glued together. This gives a 3mm, 6 ply fondo.

They all sound great to me but I have carried out major servicing to all except the Castagnari which hasn't been touched. Thinks.... I must give it a tune-up some day (cobblers shoes, etc.)

I haven't the foggiest idea why they all sound different or whatever, I'm just having fun with wood and metal and music.
If you want to know more visit the paint drying department at rec.music.makers.squeezebox


Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Reed block and sound board materials
« Reply #7 on: July 18, 2008, 01:05:07 PM »

I use two sheets of 1.5mm aircraft ply glued together. This gives a 3mm, 6 ply fondo.

Not sure that's a good idea Rees, wood laminates always have an odd number of layers for stability so you should really add a piece of veneer to one side. I'd have thought you would have been better off with a single piece of 3 or 4mm birch faced ply.

Pete.
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Reed block and sound board materials
« Reply #8 on: July 18, 2008, 02:23:40 PM »

I've had no problems with it so far. The inner faces which are glued together have the grain in the same direction so in effect it's 5 ply.
The idea was given to me by two highly respected concertina makers, so if it's good enough for them, etc.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Andy in Vermont

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 948
  • Mélodie
    • Melodeon Minutes (blog)
Re: Reed block and sound board materials
« Reply #9 on: July 18, 2008, 04:46:07 PM »

Thanks for sharing, Rees!
-Andy, who will soon literally be watch paint dry (summer in Vermont)

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Reed block and sound board materials
« Reply #10 on: July 18, 2008, 05:30:17 PM »

I use two sheets of 1.5mm aircraft ply glued together. This gives a 3mm, 6 ply fondo.

Not sure that's a good idea Rees, wood laminates always have an odd number of layers for stability so you should really add a piece of veneer to one side. I'd have thought you would have been better off with a single piece of 3 or 4mm birch faced ply.

Pete.

Ply has an odd number of layers so the stress if the wood shrinks is symmetrical (same direction on both sides) which prevents warping -- the key is to have the stackup symmetrical about the centre line (we have to do the same with multilayer PCBs) with the same direction on the two outside faces.

If this applies to a (for example) 3-ply then it also applies to any number of 3-plies glued together symmetrically -- in other words 6-ply with the plies running H-V-H-V-H-V (asymmetric) may warp, 6-ply with them running H-V-H-H-V-H (symmetric) won't -- though the unbalanced number of H and V plies will make it expand and contract unequally in the two directions.

This is one reason that plywood often has the two outer plies half the thickness of the inner ones, to get the same total thickness running both ways (e.g. H/2-V-H-V-H/2 for 5-ply).

Ian
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

melodeon

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1732
Re: Reed block and sound board materials
« Reply #11 on: July 18, 2008, 05:43:05 PM »

Rees,  If you need ALDER,  I am in the middle of alder country
I have hundreds of board feet milled from trees off my property and properly air dried over 6 yrs..

give me the dimensions you need, as exacting as you want, and I'll cut the bits for you

I have a complete wood working shop ,   so let me know
I have made parts for other builders....


I have seen reed blocks from poplar, pine, spruce, maple, mahogany , beech ,walnut and plywood
The wood is part of the formula , but as you change one thing it affects other, just as in guitars and violins

Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Reed block and sound board materials
« Reply #12 on: July 18, 2008, 07:52:37 PM »

Hi Jeff, how's it going? As I recall, you are either in California or Oregon so postage will be fairly high to the UK.

The alder will be used for reed blocks so most of it will be cut into tiny segments for the chamber walls.
Offcuts will be fine. That's the beauty of accordions, you can make them out of any old bits of wood discarded by others.

If you really want to get down to component size, the chamber walls are 10mm x 4.5mm. Headers are 10mm x 10mm. They can be as long as you like.
The blocks are glued directly on to the reed pan, Louisiana style.

Find out what the best deal on postage will be and cut the wood to fit in the carton.
Address on my website at www.melodeons.com
I will send dollars on request.
Most grateful, Rees.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

melodeon

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1732
Re: Reed block and sound board materials
« Reply #13 on: July 18, 2008, 11:56:50 PM »

Don't need any money

but 10 by 10  as in mini beams ? Will these be tapered and if so .. how
what length
and 4.5  by ten.. I assume you will be chopping these up so  minimum length ??

I'll send you a PM  as I have some other cool stuff that may be of interest to you but
you will need a "cosmic level" security clearance before I disclose  the info to you

I live in the State of Jefferson     

Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Reed block and sound board materials
« Reply #14 on: July 19, 2008, 01:12:16 PM »

4.5 x 10mm min length is 60mm.
10 x 10mm min length is 200mm. I can taper these after glueing so square section will be fine.

Looking forward to your PM. I can get fairly cosmic after a few pints of ale!

PS: I love you Jeff.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Andy in Vermont

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 948
  • Mélodie
    • Melodeon Minutes (blog)
Re: Reed block and sound board materials
« Reply #15 on: July 19, 2008, 01:29:20 PM »

Hey Jeff,
Since you are here, and we're talking about alder for reedblocks, what do you think is the property of alder that makes it good for "nailed" reedblocks? 
Your rolling in alder, we're rolling in butternut right now in VT -- there is some kind of blight that is beginning to attack the butternut, and many of the trees are getting taken down.  The sawyer from whom I get my lumber just told me that he has about 50,000 bdft in the pipeline.
-Andy

melodeon

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1732
Re: Reed block and sound board materials
« Reply #16 on: July 20, 2008, 01:13:40 AM »

Butternut is a very fine wood and was often used in furniture as a substitue and instead of walnut  chestnut etc...Much of it was stained and or varnished with dark varnish ior  painted and misidentified.

I shlould think  it would make fine casework for melodeons

Alder is interesting stuff...  it is light but not too light, hard but not too hard and homogenous grain.. once dried and cured it seems to hold its shape

It seems to not be greatly affected by the ingress and egress of moistrure
It holds hardware well ie nails and screws 
cuts well, planes well, glues well and takes a nice finish.. I paint a lot of it  I have also used it for table tops
Matter of fact I made a group of tables for the guest residence at the Alderbrook Winery north of Santa Rosa Calif  all with alder tops 

The furniture known as  MONTEREY  was nearly 100%  Alder...

I believe in "nailed" reed blocks...  not many use the technique but I see a mild interest in its revival...

About ten years ago I was a guest speaker at a State conference on the use of Oregon's indigenous timbers. At that time Alder was consider a weed tree, something that was in the way of harvesting fir and pine and spruce

When I told them that one guy was sending tens of thousands of board feet of this to Japanese electric guitar makers..  it changed their perspective.. and since the price has escalated at a percentage higher than the gas increase.
Fender guitar uses it in the Telecasters and Stratocasters along with some   swamp ash basswood and poplar...
I prefer Alder

Now it is used as a cherry substitiute and increasingly used in furniture as it takes stains better than most woods.

Martin guitar uses it in the neck blocks of their  1 series and 16 series guitars and perhaps the 15 as well as others.. ie it is used in their mortice and tenon ( not dovetail) joints...
Logged

Andy in Vermont

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 948
  • Mélodie
    • Melodeon Minutes (blog)
Re: Reed block and sound board materials
« Reply #17 on: July 20, 2008, 04:05:12 AM »

Thanks, Jeff.  Some of those characteristics sound like our "weed tree" here, hophornbeam, which is apparently in the same family as alder and birch.  The hophornbeam is, however, unusually hard -- I'm guessing that it is much harder than alder -- but it machines well and it takes a beautiful polish.  I've wondered about its possible use for reedblocks.  Most hornbeam and hophornbeam in these parts ends up in the firewood pile.
I wonder if the alder that the Italians use is a different species than what you have in your neck-o-the-woods?
-Andy

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Reed block and sound board materials
« Reply #18 on: July 20, 2008, 09:06:17 AM »

In the construction of any musical instrument, it is essential to use the finest materials to ensure the best possible acoustic response. The exact nature of those materials has usually been determined empirically over the centuries, by experiment, trial and error, etc., by many instrument makers. We owe them all a great debt.

A comparative exercise in different construction materials can be seen here:
http://uk.youtube.com/watch?v=N5aUz9cDaCY&feature=user

and an amazing performance here:
http://uk.youtube.com/watch?v=_GabHGlGm14&feature=user

;D

Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reed block and sound board materials
« Reply #19 on: July 20, 2008, 10:17:51 AM »

Ahhh, thread drift, I love it ;D

Anyone tried making a kitchen clarinet?

And here is how to make your own vegetable orchestra as played by the Vienna Vegetable Orchestra
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal