Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Electronics advice  (Read 4587 times)

0 Members and 1 Guest are viewing this topic.

Noodle

  • Louder is better, right?
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 219
  • Occasionally actually helpful
Electronics advice
« on: May 25, 2011, 03:17:59 AM »

The thread for the 'Fat Elvis' Gabbanelli has given me an idea, but I have little to no clue about electronics. I do have a cheap German junk box that I'm practising reed tuning on that I could attempt it on so in the event that I actually follow up on this idea, I was wondering if there's anyone here with any knowledge about electronics.

My idea is to have LEDs that light up around the box and/or underneath the keys as I play a note/press a button, sort of like a Rickenbacker 331 'Light Show', which has lights that flash on at certain pitches, but I don't see my idea/project being as complex as that:



Useless for daytime playing, but as an occasional thing for when it's dark or if I want to show off in the campsite at festivals, it could be quite nice.

How feasible would lights under the buttons be? Would LEDs actually show through celluloid or is it not translucent enough? What sort of circuitry would I be looking at? What sort of and how many batteries would I need for however many LEDs I decide to use? Any other advice or ideas?
Logged
Nottingham, UK.

Hohners: HA114 (C), HA114 (G)*, Liliput (C/F), Preciosa (C/F)*, 1040 (G), Imperial. Dino Baffetti Binci III (D/G), Self-made Pariselle 2.6 (G/C), Soberano (C/F), Nopka garmoshka (F#)*.

One day I'll get really good, like those really good players. One day.
*to be fixed

dahlberg

  • Custom
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 172
  • Huvvaligen
    • Spelparkering
Re: Electronics advice
« Reply #1 on: May 25, 2011, 08:52:49 AM »

Ay would say-if you want it damn simpel you buy a running lights circuit and just add more leds.
These little things you can find either as kit or readybuilt,i bought a readybuilt for under 10€ from a webshop,i have used it as a sequenser.
The wiring is very simple so i think the hardest part of make your box look like a tivoli is where to fit in the leds.
Logged

Noodle

  • Louder is better, right?
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 219
  • Occasionally actually helpful
Re: Electronics advice
« Reply #2 on: May 31, 2011, 05:23:41 AM »

I'd place my LEDs at random places around the box, on both the treble and bass side, and I'd like to have LEDs under all the keys. I'd like them to be activated by pressing the keys, but I don't want it to be as simple as, say, pressing ANY of the keys would make ALL of the LEDs light up, but have it set up as having a certain set light up if I were to press the G/A key, a set would light up, and if I were to press another button, another set would light up. I'm not sure a simple series or parallel circuit would be sufficient. Then again, I don't know. Like I say, I know little to nothing about electronics, hence why I I'm asking in case anyone here knows.

If I have no success here, I'll try a bit of googling, but since there's melodeon builders and repairers here who could advise me on whether or not it's theoretically possible to undertake such a project and are familiar with the construction of melodeons, I thought it best to ask here first. Has anyone even heard of such a thing being done before?
Logged
Nottingham, UK.

Hohners: HA114 (C), HA114 (G)*, Liliput (C/F), Preciosa (C/F)*, 1040 (G), Imperial. Dino Baffetti Binci III (D/G), Self-made Pariselle 2.6 (G/C), Soberano (C/F), Nopka garmoshka (F#)*.

One day I'll get really good, like those really good players. One day.
*to be fixed

Jim

  • Good talker
  • **
  • Offline Offline
  • Posts: 56
Re: Electronics advice
« Reply #3 on: May 31, 2011, 11:24:23 AM »

The circuitry for this oughtn't be too complicated. The LEDs need to be wired in parallel to each other and in series with the switch, with a resistor for each LED. If you want an LED to be triggered by more than one switch then some diodes would be required.  A few AAs or a 9v should power it.

The hard parts are:

1) arranging for the switches to be actuated by the buttons. You should probably use hall effect switches for this but it will complicate the circuitry a bit - probably taking it out of the complete novice realm.

2) getting the LEDs to light the buttons. I guess you need to find some translucent buttons and mount the LEDs to the back of them somehow.

If you want to make this work your best bet is to Google a simple LED circuit and buy a few components to fiddle around with. You'll soon figure it out ???.
Logged

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: Electronics advice
« Reply #4 on: May 31, 2011, 12:55:00 PM »

Hall effect switches would be a bit of overkill, reed switches and a little magnet under each key would be the way to go. Would require a little experimentation, but that's how people usually midify organ pedalboards.
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

mglamb

  • Guest
Re: Electronics advice
« Reply #5 on: May 31, 2011, 02:46:50 PM »

A diaphragm-based pressure sensor would allow for recognizing change in bellows direction.  Just sayin'...
Logged

Jim

  • Good talker
  • **
  • Offline Offline
  • Posts: 56
Re: Electronics advice
« Reply #6 on: May 31, 2011, 04:28:19 PM »

Hall effect switches would be a bit of overkill, reed switches and a little magnet under each key would be the way to go. Would require a little experimentation, but that's how people usually midify organ pedalboards.

Ah yes, I don't know why I didn't think of that!
Reed switches would be fine and don't introduce the complexity that hall effect switches would.
Logged

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: Electronics advice
« Reply #7 on: May 31, 2011, 11:03:45 PM »

Hall effect switches would be a bit of overkill, reed switches and a little magnet under each key would be the way to go. Would require a little experimentation, but that's how people usually midify organ pedalboards.

Ah yes, I don't know why I didn't think of that!
Reed switches would be fine and don't introduce the complexity that hall effect switches would.

So much of life is like that! If it makes you feel any better, when I was looking at organ pedalboards my initial impulse was microswitches.
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Electronics advice
« Reply #8 on: June 01, 2011, 12:53:38 AM »

I wish I knew what you were all talking about   ;)
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

rmenhinick

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 113
Re: Electronics advice
« Reply #9 on: June 01, 2011, 11:21:19 AM »

Reed switches are without doubt the most appropriate keyboard switches for a melodeon  ;D
Logged
Old G Poker, New DG Poker, ADG Compadre, DG Sandpiper, CF Erica, GC Delicia Popular, DG Dino Baffetti Black Pearl 3, Casali Verona 48 bass PA, (Squeezebox Squirrel :D)

StupidFingers

  • Member
  • *
  • Offline Offline
  • Posts: 45
Re: Electronics advice
« Reply #10 on: June 01, 2011, 07:55:35 PM »

The only potential downside that I can see with reed switches is that they are usually (or at least the ones I have seen) either quite large or are made of glass.  These would need to fit in the gaps between the keys, but would need to be close enough to be activated by the actuator magnet.  That should not be a problem with a keyboard mechanism of wooden construction as the levers are fairly rigidly restrained, but the metal mechanics tend to allow some lateral movement.  If the key moves too far in one or other direction, you could hit the switch (potentially causing some damage) or move the key far enough away that the switch does not activate.

That said, it's quite feasible with the right parts.

Another option would be something I believe are called photointerruptors.  They look like a little squared U shape and have a transmitter LED on one side and a receiver on the other.  If anything passes between the transmitter and receiver, then you can detect it.  You can find these in the old ball mice.  The ball contacts a roller (two of them at 90 degrees to each other actually) on an axle which has a slotted disc at one end.  The disc sits in the U so that as the disc turns the slots briefly allow the beam through so giving the speed and direction of the mouse.  As with the reed switches, you would still have the problem of keeping the keyboard aligned with the sensors, but how critical that would be depends on how far apart the transmitter and receiver are.

The only other method I can think of involves conductive rubber.  This would only work with a metal keyboard mechanism, plus I have no idea where to get the materials from.  Essentially, you would connect the mechanism to one side of the power supply then have a series of metal contacts under the keys.  To the underside of the keys, attach a conductive rubber pad (metal on metal is liable to get noisy).  When the key is pressed, the rubber pad touches the contact underneath and completes the circuit.  This is the way some of the older computer keyboards used to work, including the one on the Commodore 64.  I seem to recall there is additional resistance involved in the rubber contacts, but this could be offset by adjusting the value of the inline resistor for the LED.

With regards lighting the keyboard, I think attaching anything electrical to the keys themselves probably isn't a good idea as the connections may well fatigue resulting in a need for regular repair.  If the box allowed it, then it may be possible to replace the top face of the keyboard box with a clear plastic panel.  Overlay this with a thinner opaque layer which allows maybe 1mm of the clear plastic surrounding the key holes to remain visible.  It would then be possible to glue some rectangular LEDs to the underside of the plate to illuminate the key surround.
Logged

Ga

  • Good talker
  • **
  • Offline Offline
  • Posts: 62
Re: Electronics advice
« Reply #11 on: June 01, 2011, 08:23:12 PM »

....Or, buy one of these kits, secrete it in a fag packet-sized box, gaffa tape it to your box, or in a pocket, or even inside if you must.  Connect the LEDs by flying leads to various places around your box, buy a few different coloured LEDs for better effect (a few pence each).  Job done. 1 hour, 6 quid, in the pub in time for last orders. Could power a couple of kits from one battery if you wanted more oomph.   Simply reacts to the noises from your box.
http://www.maplin.co.uk/sound-to-light-22545
Logged

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: Electronics advice
« Reply #12 on: June 02, 2011, 01:21:43 AM »

Another option would be something I believe are called photointerruptors.  They look like a little squared U shape and have a transmitter LED on one side and a receiver on the other.  If anything passes between the transmitter and receiver, then you can detect it.  You can find these in the old ball mice.  The ball contacts a roller (two of them at 90 degrees to each other actually) on an axle which has a slotted disc at one end.  The disc sits in the U so that as the disc turns the slots briefly allow the beam through so giving the speed and direction of the mouse.  As with the reed switches, you would still have the problem of keeping the keyboard aligned with the sensors, but how critical that would be depends on how far apart the transmitter and receiver are.

Photointerruptors would also work and are very easy to use, but they tend to be very bulky, a lot bulkier than reed switches. The disadvantage with reed switches would be that it would require quite a lot of experimentation to get it right, but I don't think that flexing of the key arm would be too big a problem.

The thing with the rubber has a special name but I can't remember what it is. It is still used for calculators but would be expensive to implement for box.
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

Noodle

  • Louder is better, right?
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 219
  • Occasionally actually helpful
Re: Electronics advice
« Reply #13 on: June 02, 2011, 08:28:36 AM »

Interesting discussion so far, and thanks for the ideas. I feel at this point I should explain the box.

As I've said, it's a cheap German box that appears to have been built with the idea that it might need repair at some point is completely alien. I've had a look at the keyboard mechanism and it might prove difficult to do anything with it.



http://i89.photobucket.com/albums/k240/mr_squirtboater/DSC0000145.jpg


The keyboard and levers come as a single unit, and the keyboard itself has been glued together, and the only way to remove the wooden levers would be to break the buttons off or strip it of the celluloid and try and saw the back or front off and make a new back that could be screwed on. I fear that might be just too much to take on in terms of my skill level and lack of tools.

I suppose I should really get a really cheap Hohner to repair and try this on.

... reed switches...
The only potential downside that I can see with reed switches is that they are usually (or at least the ones I have seen) either quite large or are made of glass.

I've never seen one or even heard of them. If I were to place them so the glass is out of the way of any moving parts, I'd guess they'd be ok. The pictures I've seen lead me to believe they would be small enough and would be fine at the end of the keyboard.

A diaphragm-based pressure sensor would allow for recognizing change in bellows direction.  Just sayin'...

Interesting suggestion, but I think I'd be running out of space to put all the LEDs as it is. Perhaps a project for a 3 row or something the size of a 2 row 4 voice Paolo Soprani.

The only potential downside that I can see with reed switches is that they are usually (or at least the ones I have seen) either quite large or are made of glass.  These would need to fit in the gaps between the keys, but would need to be close enough to be activated by the actuator magnet.  That should not be a problem with a keyboard mechanism of wooden construction as the levers are fairly rigidly restrained, but the metal mechanics tend to allow some lateral movement.  If the key moves too far in one or other direction, you could hit the switch (potentially causing some damage) or move the key far enough away that the switch does not activate.
The levers on this box are wood and there is indeed little movement from side to side. If I was to attempt this on a box with metal levers, I could probably glue some wood between them to keep them in line


Quote
Another option would be something I believe are called photointerruptors.  They look like a little squared U shape and have a transmitter LED on one side and a receiver on the other.  If anything passes between the transmitter and receiver, then you can detect it.  You can find these in the old ball mice.  The ball contacts a roller (two of them at 90 degrees to each other actually) on an axle which has a slotted disc at one end.  The disc sits in the U so that as the disc turns the slots briefly allow the beam through so giving the speed and direction of the mouse.  As with the reed switches, you would still have the problem of keeping the keyboard aligned with the sensors, but how critical that would be depends on how far apart the transmitter and receiver are.
That sounds a little beyond my understanding. I'll try googling it later when my head's not so fried to see what you mean and to find some other examples.

Quote
The only other method I can think of involves conductive rubber.  This would only work with a metal keyboard mechanism, plus I have no idea where to get the materials from.  Essentially, you would connect the mechanism to one side of the power supply then have a series of metal contacts under the keys.  To the underside of the keys, attach a conductive rubber pad (metal on metal is liable to get noisy).  When the key is pressed, the rubber pad touches the contact underneath and completes the circuit.  This is the way some of the older computer keyboards used to work, including the one on the Commodore 64.  I seem to recall there is additional resistance involved in the rubber contacts, but this could be offset by adjusting the value of the inline resistor for the LED.

The thing with the rubber has a special name but I can't remember what it is. It is still used for calculators but would be expensive to implement for box.

I've had a quick look and it would appear that it is indeed not cheap

Quote
With regards lighting the keyboard, I think attaching anything electrical to the keys themselves probably isn't a good idea as the connections may well fatigue resulting in a need for regular repair.  If the box allowed it, then it may be possible to replace the top face of the keyboard box with a clear plastic panel.  Overlay this with a thinner opaque layer which allows maybe 1mm of the clear plastic surrounding the key holes to remain visible.  It would then be possible to glue some rectangular LEDs to the underside of the plate to illuminate the key surround.


Given the A/D tuning of this box, I wouldn't be taking it out to use all that much so I wouldn't imagine the connectors suffering too much. Then again, your suggestion does sound rather appealing. If I did this on a B/C or D/G box, I'd probably use that idea instead as it'd get far more use.

....Or, buy one of these kits, secrete it in a fag packet-sized box, gaffa tape it to your box, or in a pocket, or even inside if you must.  Connect the LEDs by flying leads to various places around your box, buy a few different coloured LEDs for better effect (a few pence each).  Job done. 1 hour, 6 quid, in the pub in time for last orders. Could power a couple of kits from one battery if you wanted more oomph.   Simply reacts to the noises from your box.
http://www.maplin.co.uk/sound-to-light-22545
Looks like a nice bit of kit, but it seems a bit basic for what I'm after. I don't want all the LEDs to light at once, and it might become confused in a noisy session.

I wish I knew what you were all talking about   ;)
Join the club :D I've forgotten what little basic electronics they taught me in GCSE science and design tech. My memory has got as far as parallel and series circuits...
Logged
Nottingham, UK.

Hohners: HA114 (C), HA114 (G)*, Liliput (C/F), Preciosa (C/F)*, 1040 (G), Imperial. Dino Baffetti Binci III (D/G), Self-made Pariselle 2.6 (G/C), Soberano (C/F), Nopka garmoshka (F#)*.

One day I'll get really good, like those really good players. One day.
*to be fixed

Jim

  • Good talker
  • **
  • Offline Offline
  • Posts: 56
Re: Electronics advice
« Reply #14 on: June 02, 2011, 12:01:57 PM »

The keyboard and levers come as a single unit, and the keyboard itself has been glued together,

I have one of those. The keyboards are nasty. And the springs keep breaking. Maybe you could mount the magnets on the back of the palettes and the switches on the grill. Maybe with some spacers to position the switches correctly. Or something ???. I don't think it matters for your purposes if it fails to trigger occasionally.

Either way, it seems like you have so many unknowns, some experimentation is in order. This place sells everything you need - and the components are not very expensive.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal