Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2] 3 4   Go Down

Author Topic: Going to make a box - what should I know?  (Read 15979 times)

0 Members and 1 Guest are viewing this topic.

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Going to make a box - what should I know?
« Reply #20 on: June 09, 2011, 05:03:55 PM »

I'm working on building my own small 1 voice instrument as a first try at building.

Do start with the reeds and reed blocks. And a table saw is essential for cutting most of the parts needed for the reed blocks. I've developed some simple jigs, easily built for assembling glued up reed blocks. I can now make reed blocks very quickly. Let me know if you want pictures of the jigs.

Also, when building blocks by assembling them, pay close attention to the grain direction. I always make sure that my chamber sides and the plate between the two sides of a double reedblock are quarter sawn. The wood is much less likely to warp over time. Most soundboards for guitars, harpsichords, etc. must be made from quarter sawn wood to prevent warping. A good practice for cutting the strips of wood for the parts is to joint or plane one face of the block you're resawing till you see medullary rays on the surface then saw your strip off.

While we're talking about building reed blocks, there's one step in their manufacture that I'm stumped by. After I glue the reed block chamber side pieces to the backing plate, and put on the top cap, how do I cut the block of chambers at an angle such that the top of the block is narrower than the bottom were the bottom plate will go? Hohner and other manufacturer's blocks have an "A" shape to the reedblock, making it easier to get to the reeds for tuning and keeping the vibrating tongues from interfering with each other. Anyway, I have yet to figure out how to do the cut on a table saw in a way that is safe for the operator. How to the manufacturers do that cut safely and support the block during the cut? Photos would be most helpful. Is a different tool set up better than a table saw for this?

In my own research about building reed blocks I've run into differences in the thickness of the chamber walls. Some manufacturers use 4mm walls, others use 6mm walls. The thinner walls will allow you to make a smaller instrument, true, but what does the thinner wall do for the sound of the instrument as opposed to thicker walls? Thicker walls make it easier to wax on the reeds or fit screws between the reedplates if they're nailed on.

BTW, my current scrap pile is just getting bigger.

Good luck and keep us posted on what you're doing.
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Going to make a box - what should I know?
« Reply #21 on: June 09, 2011, 05:18:58 PM »

While we're talking about building reed blocks, there's one step in their manufacture that I'm stumped by. After I glue the reed block chamber side pieces to the backing plate, and put on the top cap, how do I cut the block of chambers at an angle such that the top of the block is narrower than the bottom were the bottom plate will go?

Table saw with blade tilted?
or on a belt sander.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Going to make a box - what should I know?
« Reply #22 on: June 09, 2011, 05:41:31 PM »

While we're talking about building reed blocks, there's one step in their manufacture that I'm stumped by. After I glue the reed block chamber side pieces to the backing plate, and put on the top cap, how do I cut the block of chambers at an angle such that the top of the block is narrower than the bottom were the bottom plate will go?

Table saw with blade tilted?
or on a belt sander.

Theo, first off, do you cut the reed block with the top cap down on the the table or with the bottom of the block on the table?

I've been looking at the setup for using the Table saw on a block with the bottom of the block on the table and the blade tilted and it scares me to death. Reedblocks are so small that they would be completely buried between the blade and the fence.

Cutting one side of the block would allow the other side to sit flat against the fence, but cutting the second side is the real problem. Can't see how that's done, yet. Adjust the blade to twice the angle so the first side can sit flat against the fence? That would leave the bottom of the block riding on one corner. Hope this all makes sense. I should draw a picture of what I'm thinking.

Belt sander does make sense though I don't own one. Hmm, that's getting me thinking about a set up for my plunge router that might just work.
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

nfldbox

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 492
Re: Going to make a box - what should I know?
« Reply #23 on: June 09, 2011, 05:50:25 PM »

I will NEVER build an accordion but as a novice repairer I am so enjoying this thread. It is making me think about the boxes in a totally different way.
Logged
BC Cairdin
BC Hohner Double Ray
Bouchard en Ré

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Going to make a box - what should I know?
« Reply #24 on: June 09, 2011, 06:31:07 PM »

Theo, first off, do you cut the reed block with the top cap down on the the table or with the bottom of the block on the table?

I've not done this bit yet!  I suppose it depends a bit on the size and quality of your table saw.  Sander would be a slower but safer option.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

squeezy

  • Quick starter (now lagging behind)
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1317
  • Hohner Cornelia (mixte D/G/o&s)
    • www.johnspiers.co.uk
Re: Going to make a box - what should I know?
« Reply #25 on: June 09, 2011, 06:40:43 PM »

So - regarding the reeds:  If I want to get a set of Binci professional reeds, how does one go about the business of getting them?  And do they need to be ordered with special reed numbers to indicate notes (I seem to remember that was the way they could be definitely identified with notes when I worked for The Music Room).

Are there any other suppliers out there who one can deal with personally to get reeds?  I liked the look of the Czech website Harmonikas being talked about on the other thread.  But I have no experience of the quality of Czech tipo a mano reeds.

Cheers

Squeezy
Logged
Squeezy

Sometimes wrong, sometimes right ... but always certain!

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Going to make a box - what should I know?
« Reply #26 on: June 09, 2011, 06:51:49 PM »

So - regarding the reeds:  If I want to get a set of Binci professional reeds, how does one go about the business of getting them?  And do they need to be ordered with special reed numbers to indicate notes (I seem to remember that was the way they could be definitely identified with notes when I worked for The Music Room).

Are there any other suppliers out there who one can deal with personally to get reeds?  I liked the look of the Czech website Harmonikas being talked about on the other thread.  But I have no experience of the quality of Czech tipo a mano reeds.

Cheers

Squeezy

Attached is the reed order forms for my 2.6 row that I am making at Emanuel's course next month. Should be how to order reeds. They do use reed numbers and Tonic SolFa names. You should be able to work out the numbering system from the forms.

Hope this helps

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Going to make a box - what should I know?
« Reply #27 on: June 09, 2011, 06:55:57 PM »

So - regarding the reeds:  If I want to get a set of Binci professional reeds, how does one go about the business of getting them?  And do they need to be ordered with special reed numbers to indicate notes (I seem to remember that was the way they could be definitely identified with notes when I worked for The Music Room).

Are there any other suppliers out there who one can deal with personally to get reeds?  I liked the look of the Czech website Harmonikas being talked about on the other thread.  But I have no experience of the quality of Czech tipo a mano reeds.

Cheers

Squeezy

You can also order reeds from Michael at Irish Dance Master. He's very helpful.
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Going to make a box - what should I know?
« Reply #28 on: June 09, 2011, 07:40:08 PM »

 how do I cut the block of chambers at an angle such that the top of the block is narrower than the bottom were the bottom plate will go?

I tilt my blade 2 or 3 degrees, and I have a jig that holds the block straight up, this tapers toward the top of the block.  The jig also holds the block out at a slight angle so the block is tapered from low reed chamber to high reed chamber.  On my jig I can use shims to adjust the low to high taper.  For standing blocks, I taper before gluing to the divider, which is essentially a wedge to keep the 2 outside lines of the opposing reed blocks parrallel.

Here is a link that shows a pic of my jig.  In the pic I am cutting a lay down block, but I use the same jig to cut standing blocks.  The screws sticking out the top are makeshift handles.  This was a temporary thrown together test jig that I've meant to clean up and add to, just never have.  http://www.lansegriseaccordions.com/buildproc/2-2%20cutting%20reed%20block%20angles.JPG 
« Last Edit: June 09, 2011, 07:42:29 PM by blafleur »
Logged

squeezy

  • Quick starter (now lagging behind)
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1317
  • Hohner Cornelia (mixte D/G/o&s)
    • www.johnspiers.co.uk
Re: Going to make a box - what should I know?
« Reply #29 on: June 09, 2011, 08:15:45 PM »

Attached is the reed order forms for my 2.6 row that I am making at Emanuel's course next month. Should be how to order reeds. They do use reed numbers and Tonic SolFa names. You should be able to work out the numbering system from the forms.

Hope this helps

Thanks for that Lester, really helpful indeed and reminded me of the reed numbering system, yes with A440 as number 24.  There is as page on the Harmonikas.cz website that has a great diagram of all the reeds they supply with reed numbers in pale green.  

Good luck with the course!  I'm sure that probably is the right way to learn.

Logged
Squeezy

Sometimes wrong, sometimes right ... but always certain!

squeezy

  • Quick starter (now lagging behind)
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1317
  • Hohner Cornelia (mixte D/G/o&s)
    • www.johnspiers.co.uk
Re: Going to make a box - what should I know?
« Reply #30 on: June 09, 2011, 08:18:02 PM »

Here is a link that shows a pic of my jig.  In the pic I am cutting a lay down block, but I use the same jig to cut standing blocks.  The screws sticking out the top are makeshift handles.  This was a temporary thrown together test jig that I've meant to clean up and add to, just never have.  http://www.lansegriseaccordions.com/buildproc/2-2%20cutting%20reed%20block%20angles.JPG 

Hi bafleur - thank you too.

The pictures on your website are all very illuminating and your boxes look lovely.

Cheers

Squeezy
Logged
Squeezy

Sometimes wrong, sometimes right ... but always certain!

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: Going to make a box - what should I know?
« Reply #31 on: June 09, 2011, 08:20:26 PM »

Of course if you don't fancy the table saw and have huge amounts of money to waste then there is always this: http://forum.melodeon.net/index.php/topic,5643.0.html
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

squeezy

  • Quick starter (now lagging behind)
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1317
  • Hohner Cornelia (mixte D/G/o&s)
    • www.johnspiers.co.uk
Re: Going to make a box - what should I know?
« Reply #32 on: June 09, 2011, 08:39:44 PM »

Thanks Ukebert!  I don't think I'll be getting the Jointmaker Pro first up!  Looks pretty impressive though!
Logged
Squeezy

Sometimes wrong, sometimes right ... but always certain!

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: Going to make a box - what should I know?
« Reply #33 on: June 09, 2011, 08:49:41 PM »

It does, up until the point at which you notice the price! :P
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

squeezy

  • Quick starter (now lagging behind)
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1317
  • Hohner Cornelia (mixte D/G/o&s)
    • www.johnspiers.co.uk
Re: Going to make a box - what should I know?
« Reply #34 on: June 09, 2011, 08:55:55 PM »

Does anyone have any opinions on the best way to go about building the box? (which is, when you look at the complexity of the keyboard and reed blocks, just a box!)

There are many differences I have seen on instruments in this respect.  For example, the Oakwood I sold had walls only 5mm thick but they were significantly braced inside on the corners, whereas the Eric Martin has walls 10mm thick (essential I think for the way it is attached to the bellows with a screw rather than bellows pins) - yet one doesn't feel that significantly heavier than the other.

Also would any of you ever consider approaching the Bellows frame by making them out of the same pieces of wood, i.e build the box and then saw a centimetre of it or so off for a bellows frame of exactly matching dimensions, or is that silly/impractical?

Cheers,

Squeezy
Logged
Squeezy

Sometimes wrong, sometimes right ... but always certain!

Keithypete.

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 917
Re: Going to make a box - what should I know?
« Reply #35 on: June 09, 2011, 09:14:14 PM »

Of course if you don't fancy the table saw and have huge amounts of money to waste then there is always this: http://forum.melodeon.net/index.php/topic,5643.0.html


  I do a bit of shuttering work now & then so I have a skill saw. A cheap chinese skill saw. By mounting it onto a piece of 9 mm ply I have converted it into a table saw. It is still fully adjustable and along with a cheap chinese router many things are possible.
Logged
Beltuna Sara II - B/C flavour.
Borsini - G,D,A.
Pokerwork B/C.
PRIMATONA IV, B/C.

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Going to make a box - what should I know?
« Reply #36 on: June 09, 2011, 10:01:56 PM »

Does anyone have any opinions on the best way to go about building the box? (which is, when you look at the complexity of the keyboard and reed blocks, just a box!)

There are many differences I have seen on instruments in this respect.  For example, the Oakwood I sold had walls only 5mm thick but they were significantly braced inside on the corners, whereas the Eric Martin has walls 10mm thick (essential I think for the way it is attached to the bellows with a screw rather than bellows pins) - yet one doesn't feel that significantly heavier than the other.

Squeezy,

My own process has been to do lots of drawings with my very limited CAD program. It's only for 2D drawing but it allows me to create reuseable objects that can be moved around, duplicated for designs I like, and so forth. I start with exact measurements of the reed plates themselves, draw them, then start putting together different designs based on my current ideas of what I want to do with the instrument.

Here are some thoughts to consider:
Do you want the instrument to be extremely small, similar to a Preciosa? You'll want to make the treble side reed blocks in a similar fashion, mounted flat, directly to the sound board. Ukebert has information from another maker about issues to do with volume discrepancies between the upper set of flat mounted reed blocks and the lower reed blocks when the reed plates are not specifically for a Preciosa. Be aware that the Preciosa reed plates are about 14mm, Hohner T reed plates are 16mm and some Italian reed plates are 17mm.

With standing reed blocks you need to figure out whether you want the blocks to stick up into the space between the bellows folds, creating a much wider box, or do you want to fit the top of the blocks entirely within the treble case and under the bellows.

I'm starting with the reed plates, reed blocks and treble side, allowing those measurements to dictate the inside and outside dimensions of the case on the treble side, then duplicating those dimensions for the bass side and seeing what I end up with for space between the bellows folds. The bass reed blocks can sometimes dictate a slightly larger instrument because they do need to stick up inside the bellows.

There are many options for reed block arrangements, each one a compromise on size, weight, complexity, especially in the keyboard complexity.

Given a 21 button box, you could arrange the reeds in the two standard reed blocks, 11 reeds in one, 10 reeds in the other, corresponding to the two keys of the instrument. Or, you can split the reeds amongst three blocks, creating a smaller instrument at the expense of making the keyboard mechanism more complicated. Doable, at least on paper. I've been playing with just such a design myself. It is possible to arrange the reeds and reed blocks into a box so small that the buttons and keyboard size become a limiting factor in overall size.

If you're going for a LMM, then you'll probably want to go with three blocks with the middle block for the L reeds, pretty standard design. And you can add registers. Both treble and/or bass.

Then there's designs with extra buttons, like the Preciosa and others, that have extra accidentals on the third row. Adding more accidentals makes the instrument wider.

Wall thickness is another decision. Do you want plywood with bracing or solid wood. I've been a musical instrument maker in a past life and prefer solid wood so my instrument will have solid wood. That said, I'm making sure to pay strict attention to grain orientation in the wood in order to allow me to use thinner pieces of wood. I'm hoping to keep the final thickness of the case wood to 5 - 6 mm, not unreasonable, I hope.

All of this is probably very obvious to some, but for me, I need to know what each of these options looks like, how big a box will probably result, in order to make decisions about what I want. Only after doing the design work can I make a decision and then start  cutting wood. I'm still ending up with lots of unuseable pieces because the building process then starts to inform the design process, i.e. do this process before that process, etc. I've been through three or four different types of jigs to build the reedblocks alone.

Hope some of this helps with your building process.

« Last Edit: June 09, 2011, 10:06:15 PM by Telemorris »
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Going to make a box - what should I know?
« Reply #37 on: June 09, 2011, 10:08:48 PM »

Also would any of you ever consider approaching the Bellows frame by making them out of the same pieces of wood, i.e build the box and then saw a centimetre of it or so off for a bellows frame of exactly matching dimensions, or is that silly/impractical?
No - that's not silly or impractical, but exactly how we made them on Emmanuel's melodeon-making course. Each combined end/bellows frame was made separately, and eventually the bellows frame and end were sawn through to separate them.

Paul Johnson (occasionally posts on here) took a good series of photos during the course to show progress. You can see them here:
http://www.flickr.com/photos/boxplayer/sets/72157608254841685/with/2961563523/

This one shows one of the ends partially cut through to eventually form the bellows frame and the end proper.
http://www.flickr.com/photos/boxplayer/2961566089/in/set-72157608254841685/
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Going to make a box - what should I know?
« Reply #38 on: June 09, 2011, 10:15:20 PM »

Also would any of you ever consider approaching the Bellows frame by making them out of the same pieces of wood, i.e build the box and then saw a centimetre of it or so off for a bellows frame of exactly matching dimensions, or is that silly/impractical?

If I'm understanding you correctly, that's what I've done on my last 3 or 4, one being a pinned frame.  I make the box out of wide enough pieces that I cut the frame in half for my standard accordion, and for the pinned one, a smaller piece to attach to the bellows. I like doing that because with figured wood the grain matches.  Also no worry about misaligning the adjoining frames.

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Going to make a box - what should I know?
« Reply #39 on: June 09, 2011, 10:29:40 PM »

 how do I cut the block of chambers at an angle such that the top of the block is narrower than the bottom were the bottom plate will go?

I tilt my blade 2 or 3 degrees, and I have a jig that holds the block straight up, this tapers toward the top of the block.  The jig also holds the block out at a slight angle so the block is tapered from low reed chamber to high reed chamber.  On my jig I can use shims to adjust the low to high taper.  For standing blocks, I taper before gluing to the divider, which is essentially a wedge to keep the 2 outside lines of the opposing reed blocks parrallel.

Here is a link that shows a pic of my jig.  In the pic I am cutting a lay down block, but I use the same jig to cut standing blocks.  The screws sticking out the top are makeshift handles.  This was a temporary thrown together test jig that I've meant to clean up and add to, just never have.  http://www.lansegriseaccordions.com/buildproc/2-2%20cutting%20reed%20block%20angles.JPG 

Blafleur,

Thanks very much for posting the pic. I'm going to make one for myself soon. Interesting that you taper the divider to offset the outside taper. I like that. How do you make the tapered divider? My guess would be some sort of holding form with a taper that holds the divider while it goes through a thicknesser.
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F
Pages: 1 [2] 3 4   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal