Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 2 [3] 4   Go Down

Author Topic: Going to make a box - what should I know?  (Read 16004 times)

0 Members and 1 Guest are viewing this topic.

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Going to make a box - what should I know?
« Reply #40 on: June 09, 2011, 10:36:27 PM »

Does anyone have any opinions on the best way to go about building the box? (which is, when you look at the complexity of the keyboard and reed blocks, just a box!)

There are many differences I have seen on instruments in this respect.  For example, the Oakwood I sold had walls only 5mm thick but they were significantly braced inside on the corners, whereas the Eric Martin has walls 10mm thick (essential I think for the way it is attached to the bellows with a screw rather than bellows pins) - yet one doesn't feel that significantly heavier than the other.

Also would any of you ever consider approaching the Bellows frame by making them out of the same pieces of wood, i.e build the box and then saw a centimetre of it or so off for a bellows frame of exactly matching dimensions, or is that silly/impractical?

Cheers,

Squeezy

My current design is going to use 5-6mm thick solid wood pieces for the case. I'm going to miter the corners to do the initial glue up with a slot for the soundboard in each piece so the soundboard is glued in. Then I'll glue triangular pieces into all the inside corners for strength. After they dry, I'll cut the outside corners of the box and glue in contrasting pieces of wood to strengthen the outside corners. Those pieces will then be rounded over, probably using a router bit.

Your idea for bellows frames makes a great deal of sense to me. Will you glue a wider piece onto the bellows side, a frame of sorts, to provide more surface area for the card stock to glue to?
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

squeezy

  • Quick starter (now lagging behind)
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1317
  • Hohner Cornelia (mixte D/G/o&s)
    • www.johnspiers.co.uk
Re: Going to make a box - what should I know?
« Reply #41 on: June 09, 2011, 10:38:55 PM »

Thanks everyone for the last few posts which are very good advice.

I knew I could count on people here!

For the record - I'm not going for a record breaking small box like the Preciosa, but one with a small enough bellows cross section to give a good kick to the reeds / but not so small that it overblows them.  I'm going for a 3 voice instrument with a LMM configuration.  If there is room I will see if I can get 12 basses in - otherwise it's just the standard 8.  I will be trying to keep in mind coupler/stop systems for the low voice on the right hand and the thirds on the chords.

That has little bearing on the advice here though.  I'm not looking for specifics, just general things to consider in the design process.  I'm particularly grateful for the advice on grain direction of the wood used which I just would have never thought about.

Cheers

Squeezy
Logged
Squeezy

Sometimes wrong, sometimes right ... but always certain!

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Going to make a box - what should I know?
« Reply #42 on: June 09, 2011, 10:45:37 PM »

Thanks everyone for the last few posts which are very good advice.

I knew I could count on people here!

For the record - I'm not going for a record breaking small box like the Preciosa, but one with a small enough bellows cross section to give a good kick to the reeds / but not so small that it overblows them.  I'm going for a 3 voice instrument with a LMM configuration.  If there is room I will see if I can get 12 basses in - otherwise it's just the standard 8.  I will be trying to keep in mind coupler/stop systems for the low voice on the right hand and the thirds on the chords.

That has little bearing on the advice here though.  I'm not looking for specifics, just general things to consider in the design process.  I'm particularly grateful for the advice on grain direction of the wood used which I just would have never thought about.

Cheers

Squeezy

Don't forget that chord blocks can be set up with thirds, or leave them out entirely making for a smaller block that comes to about the same size as the block with the fundamentals. But that's the dilemma, to have thirds or not. Without thirds, you don't need to create a register either making for less complexity in the construction.
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

squeezy

  • Quick starter (now lagging behind)
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1317
  • Hohner Cornelia (mixte D/G/o&s)
    • www.johnspiers.co.uk
Re: Going to make a box - what should I know?
« Reply #43 on: June 09, 2011, 11:08:08 PM »

Don't forget that chord blocks can be set up with thirds, or leave them out entirely making for a smaller block that comes to about the same size as the block with the fundamentals. But that's the dilemma, to have thirds or not. Without thirds, you don't need to create a register either making for less complexity in the construction.

Well - having owned boxes with both configurations I'm firmly of the mind that a real melodeon has got thirds.  For me the thin sound of a thirdless box is a bit feeble for proper dance accompaniment, but sometimes it is essential because of the harmony you are trying to make.  Because of this - I am working on a sprung coupler mechanism which can be worked with the thumb under the air button like a shift key that can take the thirds out while playing - this will also have a lock function that can take the thirds out all the time if wanted.  Only at the development stage at the moment - but it seems eminently doable.

Obviously that's only my opinion - and yes I take on board that an entirely thirdless box is desirable from many construction angles.

Cheers

Squeezy
Logged
Squeezy

Sometimes wrong, sometimes right ... but always certain!

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Going to make a box - what should I know?
« Reply #44 on: June 10, 2011, 12:05:47 AM »

Your idea for bellows frames makes a great deal of sense to me. Will you glue a wider piece onto the bellows side, a frame of sorts, to provide more surface area for the card stock to glue to?

I do beef up the gluing surface to the bellows on all of them.  Been experimenting on doing it with keeping added weight to a minimum.  This was my first pinned bellows and I didn't have one to go by, so kinda winging it, but here is an in process pic. http://www.lansegriseaccordions.com/jamey.jpg  The corners aren't rounded or contrasting, at customer's request.  If you look close you can see the line where the bellows frame is cut.  The lightning bolt base box holes are customer's request also.

I did the contrasting corner thing on the last 3.  I used hide glue because it makes such a tight joint without clamping.
« Last Edit: June 10, 2011, 12:09:45 AM by blafleur »
Logged

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Going to make a box - what should I know?
« Reply #45 on: June 10, 2011, 12:18:04 AM »

Blafleur,

Beautiful! What did you use for a finish? I like the color on the curly maple very much.

How thick are the pieces of wood you're using  for the case, or are you using solid wood?
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Going to make a box - what should I know?
« Reply #46 on: June 10, 2011, 02:54:20 AM »

i AM going to make a box - a two-row small 3 voice! 

PS - I fully intend to ruin large amounts of wood, swear a lot, give up a couple of times and spend lots of money on equipment it turns out I don't need on this project.

Ha ha , that's the spirit.

Blafleur,
Beautiful! What did you use for a finish? I like the color on the curly maple very much.
How thick are the pieces of wood you're using  for the case, or are you using solid wood?

Aniline dyes and lacquer. Can't remember the thickness, probably too thick.  I'd be curious if there is a standard accepted thickness for frames on pinned style.

Andy in Vermont

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 948
  • Mélodie
    • Melodeon Minutes (blog)
Re: Going to make a box - what should I know?
« Reply #47 on: June 10, 2011, 02:43:18 PM »

I fully intend to ruin large amounts of wood, swear a lot, give up a couple of times and spend lots of money on equipment it turns out I don't need on this project.

Squeezy,
This has been a great thread!
I've been planning to build a box and have actually spent years honing my skills for the various parts -- this does not have to take as long as I've spent but in my defense I'm doing everything with hand tools, and it has been a pleasure to build various useful objects and pieces of furniture in the process.
One thing you might consider is to make several boxes -- yes, actual boxes (not accordions) -- that incorporate aspects of the design or process.
This relates to the discussion above concerning using the same wood for the bellows frame etc.  I'm experimenting with making a single box, with a faceplate glued into a groove at each end-- i.e. a completely sealed box.  Before glueing, I cut grooves on the inside of the four sides.  After glue up, grooves are cut on the outside of the sides, offset from the inside grooves by exactly the width of the groove.  When the outside grooves are cut to their full depth (I'm using a plough plane -- a Record 044), the box pops apart, and what is left is a series of interlocking components. 
It all sounds much more complicated than it is, and it would be even easier with machines than with the tools I'm using.  Next time I make one, I'll try to remember to take pictures to document the process.
Cheers,
Andy

Peter_T

  • Good talker
  • **
  • Offline Offline
  • Posts: 88
Re: Going to make a box - what should I know?
« Reply #48 on: June 10, 2011, 03:22:26 PM »

Could 3d printing have a part to play?

Print me a Stradivarius
Logged
D/G Pokerwork, perfectly dreadful Scholer G/D Anglo, guitars, harmonicas, etc

Aunty Social

  • Member
  • *
  • Offline Offline
  • Posts: 45
  • Punk's not dead!
Re: Going to make a box - what should I know?
« Reply #49 on: June 10, 2011, 04:02:08 PM »

If anyone has ideas for construction and some starting dimensions to go on I may be able to help. I own and use a 3D CAD system that makes visualising ideas so much easier by modeling all the parts and assembling them on the pc. Easy to make changes before committing to sawing! The beauty is that you also create accurate drawings of all the pieces you need to cut. Might be worthwhile PMing a fag packet sketch my way....Be an interesting project to get involved in.
Logged
Never do as you are told.

Graham W

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 277
Re: Going to make a box - what should I know?
« Reply #50 on: June 10, 2011, 04:36:10 PM »

If anyone has ideas for construction and some starting dimensions to go on I may be able to help. I own and use a 3D CAD system that makes visualising ideas so much easier by modeling all the parts and assembling them on the pc. Easy to make changes before committing to sawing! The beauty is that you also create accurate drawings of all the pieces you need to cut. Might be worthwhile PMing a fag packet sketch my way....Be an interesting project to get involved in.

Ahh  ;D   I too am making a box (loosely, at the current rate it will be years before it appears in the wood).  I plan to make my own mechanism, which will involve cutting all the levers out of alloy sheet - for which a CAD drawing for water jet cutting (or some other kind of CNC cutting) would be a huge help.  I might be some time though . . . . .
Logged

Aunty Social

  • Member
  • *
  • Offline Offline
  • Posts: 45
  • Punk's not dead!
Re: Going to make a box - what should I know?
« Reply #51 on: June 10, 2011, 05:54:30 PM »

That's a straightforward process. There's a fantastic company local to me that specialise in laser cutting. I produce the pattern in a format that plugs straight into the laser machine and Bob's your uncle!
Logged
Never do as you are told.

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Going to make a box - what should I know?
« Reply #52 on: June 10, 2011, 06:02:24 PM »

One more thought about using wood. It's very important to pay attention to the humidity level in the room where you're doing your gluing up, especially if you are gluing braces or other pieces that cross the grain of, say, a soundboard. Guitar tops have cross braces that limit the expansion and contraction of the top. If you glue the cross braces on during a spell of high humidity, you run the risk of inducing cracks in the top when the instrument moves to an area of low humidity. Likewise, if you glue the braces on during a period of low humidity and the instrument later moves into a climate of high humidity, the cross braced wood can buckle and warp until the instrument dries out. Finishes don't make much of a difference to this expansion and contraction of wood because the inside of the instrument is never varnished, or only rarely.

You'll want to do your glue up when the humidity is between 50% and 55%. Another way to figure out what humidity you should aim for is to look at the weather data for all the places you're going to play. Find out the highest and the lowest humidity that the instrument will likely encounter and glue up at a percentage half way between the two extremes.

When I studied as a luthier, we constructed a box out of plywood with a heat lamp tied to a light dimmer switch and located in the bottom of the box. We adjusted the humidity either with heat to dry out or by hanging damp rags in the box to increase moisture. The soundboard wood was stored in the box for at least a day before glueing up cross braces to allow the wood to come to equilibrium with the ambient humidity in the box.

That said, I doubt whether you need to pay much attention to humidity when gluing up your reedblocks because there is little cross grain contact. Only the back plate or divider between two rows of chambers would give you any potential problems.

Using hide glue for musical instruments is highly recommended. The stuff just doesn't give up its grip on the wood, no creap, easy clean up even long after the glue has dried, and mistakes are usually very easy to take apart. While I've been using PVA wood glue, I've decided to go back to my hide glue because it's so reliable. And no real need for a special pot for the glue. I use an old slow cooker/"crock pot" with the power run through a light dimmer switch to adjust the temperature. The glue sits in an old coffee or tea mug and the mug sits in a water bath. Easy. You can pick up an old slow cooker for a dollar or two at a garage sale here in the US.

Telemorris
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Going to make a box - what should I know?
« Reply #53 on: June 10, 2011, 09:07:43 PM »

Interesting that you taper the divider to offset the outside taper. I like that. How do you make the tapered divider? My guess would be some sort of holding form with a taper that holds the divider while it goes through a thicknesser.

Several ways you could do it, that's one.  I've used that same jig I showed earlier, but lately I've used my band saw.  I try to use a thick enough piece that after I split it I have at least 2 usable wedges.

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Going to make a box - what should I know?
« Reply #54 on: June 10, 2011, 09:19:34 PM »

each end-- i.e. a completely sealed box.  Before glueing, I cut grooves on the inside of the four sides.  After glue up, grooves are cut on the outside of the sides, offset from the inside grooves by exactly the width of the groove.  When the outside grooves are cut to their full depth (I'm using a plough plane -- a Record 044), the box pops apart, and what is left is a series of interlocking components. 
It all sounds much more complicated than it is, and it would be even easier with machines than with the tools I'm using.  Next time I make one, I'll try to remember to take pictures to document the process.
Cheers,
Andy

I thought this was the answer until I realised that a saw blade's width would be too weak for a bellows pin. Nice idea, though.  (:)
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Going to make a box - what should I know?
« Reply #55 on: June 10, 2011, 09:45:09 PM »


I thought this was the answer until I realised that a saw blade's width would be too weak for a bellows pin. Nice idea, though.  (:)

A saw blade width would be too small. However, I've done the same type of slot design using an 18mm router bit with success. 18mm for each side of the "tongue" should be enough to hold a pin. The issue for me with this design is how thick the wood in the case should be in the first place since both sides of the interlocking "tongues" are only half the thickness of the original piece of wood.

What is the minimum thickness for the portion of a bellows frame that is pierced by a pin?
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Going to make a box - what should I know?
« Reply #56 on: June 10, 2011, 10:51:42 PM »

I reckon at least 10mm.
Perhaps glue a strip around the inside of the frame to thicken it up before cutting?
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Going to make a box - what should I know?
« Reply #57 on: June 11, 2011, 09:06:10 PM »

Not sure that I can picture exactly what Andy is describing, but if I am, I don't think he was saying it was a sawblade width, but a plow blade width, however thick that is.

Here is what I did on my first and only pinned build.  Haven't put the pins or bellows on yet, but the frame has a good fit.  The triangular corner pieces were put in before I cut the frame, which allowed me to put it back together after cutting exactly as it was minus a narrow kerf saw blade width.  I then installed the inset strips using hide glue rubbed on so I didn't have to clamp, it made a tight and smooth fit.  I beefed up where the pins go, which may be overkill.  Sticks, stones, and other criticisms welcome.  Pics below, with links to see pics better. 

[img width= height=]http://www.lansegriseaccordions.com/image1.jpg[/img]

[img width= height=]http://www.lansegriseaccordions.com/image2.jpg[/img]

http://www.lansegriseaccordions.com/image1.jpg
http://www.lansegriseaccordions.com/image2.jpg
« Last Edit: June 11, 2011, 09:08:45 PM by blafleur »
Logged

Andy in Vermont

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 948
  • Mélodie
    • Melodeon Minutes (blog)
Re: Going to make a box - what should I know?
« Reply #58 on: June 12, 2011, 05:14:02 AM »

Not sure that I can picture exactly what Andy is describing, but if I am, I don't think he was saying it was a sawblade width, but a plow blade width, however thick that is.

Yes, I'm using a plough plane (Record 044) with the widest blade -- I don't recall the mm size but I'll check next time I'm in the shop. If you have only a thinner blade you make a wider grooves by ploughing the (thin) grooves, then adjusting the fences and ploughing a second groove.

People that do the same method with a table saw use a dado stack, I believe.  You can get plenty of overlap for bellows pins!
-Andy

squeezy

  • Quick starter (now lagging behind)
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1317
  • Hohner Cornelia (mixte D/G/o&s)
    • www.johnspiers.co.uk
Re: Going to make a box - what should I know?
« Reply #59 on: June 13, 2011, 12:25:39 PM »

Blimey!

That's quite a lot to digest over the weekend.  But thank you everyone who has written in on this thread.  I really do have a lot to be thinking about - but it doesn't seem as daunting as I thought even with as much detail as has been given here  ;D

I'm going to order a set of reeds and take it from there.

Cheers

Squeezy

PS - if there's something else no-one has thought of ...
Logged
Squeezy

Sometimes wrong, sometimes right ... but always certain!
Pages: 1 2 [3] 4   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal