Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 2 3 [4]   Go Down

Author Topic: Going to make a box - what should I know?  (Read 15977 times)

0 Members and 1 Guest are viewing this topic.

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Going to make a box - what should I know?
« Reply #60 on: June 13, 2011, 12:34:17 PM »

PS - if there's something else no-one has thought of ...

Almost certainly.  ;D

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Going to make a box - what should I know?
« Reply #61 on: June 13, 2011, 01:41:26 PM »

Here's a tip I got from Eric Martin.
Don't build the frame until you have the bellows. Bellows often arrive a few mm bigger or smaller than you ordered, so it's best to build the frame to fit the actual bellows.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

squeezy

  • Quick starter (now lagging behind)
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1317
  • Hohner Cornelia (mixte D/G/o&s)
    • www.johnspiers.co.uk
Re: Going to make a box - what should I know?
« Reply #62 on: June 13, 2011, 01:52:38 PM »

That's a good one Rees.  I keep liking Eric more and more!

I've encountered that problem before, when ordering replacement bellows for my instruments.
Logged
Squeezy

Sometimes wrong, sometimes right ... but always certain!

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Going to make a box - what should I know?
« Reply #63 on: June 13, 2011, 02:39:55 PM »

Don't build the frame until you have the bellows. 

I learned this also,  I don't cut frames or reed blocks to size until I have reeds and bellows.  Getting the same type reed each time should be consistent, but I don't trust it.  On bellows, I've also seen at least one out of square.

Squeezy, not only is there a lot left to bring up, you'll have questions you or us havent thought up once you get into it.  I've run into some issue on each of my builds that I didn't on the others, and you probably will too.  I guess there is a point that this will taper off, but I apparently haven't gotten there yet.

emrock

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 126
  • Busker, based in Southern Germany
Re: Going to make a box - what should I know?
« Reply #64 on: June 13, 2011, 04:40:48 PM »

I've built 2 boxes and am planning on starting number 3 soon. The first one I built is more of a display piece than a playable instrument, as I made lots of mistakes. The second has some flaws but is almost there. I learnt lots from my mistakes, and the best piece of advice I can give is to spend as much time as possible designing and planning your box as possible. There by working out any problems on paper and not wood, this will save you a lot of wasted effort. Another thing that has helped me is to try and work out things for myself and not simply copy an existing box. In doing this I have developed several new ways of making various parts of a box that I am not aware have been done before and are a lot easier for me to make.

Logged

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Going to make a box - what should I know?
« Reply #65 on: June 13, 2011, 05:01:37 PM »

.... Another thing that has helped me is to try and work out things for myself and not simply copy an existing box. In doing this I have developed several new ways of making various parts of a box that I am not aware have been done before and are a lot easier for me to make.

I too have been designing jigs that have helped me speed things up when cutting or gluing up some parts of my instrument. Emrock, I'm very interested in the jigs or techniques you've come up with for building various parts, especially reedblocks and keyboards. Photos would be most helpful too. I'll try to post some of the tricks and jigs I've developed as well.
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

TomB-R

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 598
Re: Going to make a box - what should I know?
« Reply #66 on: June 15, 2011, 01:44:27 PM »

Lots of good info already. There really is no need for expensive tools or a workshop. It could be more of a kitchen table, hand tools only, project than most instruments if you start with the right materials.

I found
http://www.modelshop.co.uk/
quite useful for my build.  Always good to get as much as possible from one supplier, otherwise the P&Ps mount up.

Don't be too alarmed by the idea of bellows making, it's doable and needn't take that long. When people see the finished article and you say you made it, they'll be asking about/looking at the bellows, [edit; amongst other things, of course,] !

I agree about the Bergflodt site being very inspiring/daunting! (And scary, those ungauarded table saws!)

Good luck to all,
Tom


« Last Edit: June 15, 2011, 03:19:13 PM by TomB-R »
Logged

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Going to make a box - what should I know?
« Reply #67 on: June 15, 2011, 03:14:44 PM »

Bergflodt's site was very inspirational to me also...what a craftsman.  My problem with his site is it made me really, really, want something I cannot have, a laser engraver.

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Going to make a box - what should I know?
« Reply #68 on: June 15, 2011, 04:55:03 PM »

Blafleur,

Thank you very much for posting the photo of your reed block cutting jig. I made one last night and was able to safely cut the angled face in all of my reed blocks. The jig held onto the reedblock firmly and worked like a charm! The next set of blocks will also have a wedge shaped divider since the setup is so easy with this jig.

Thanks for the information!
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: Going to make a box - what should I know?
« Reply #69 on: June 19, 2011, 03:58:24 AM »

So, to see if I've got this right...

1) Order reeds
2) Decide how reeds will be mounted, design blocks, build, test.
3) Based on the dimensions of the blocks, specify bellows size, order bellows (or make if you prefer).
4) Based on actual bellows, construct frames and casing, fit soundboard and blocks.
5) Finishing (I predict that as with so many other projects, "finishing" will take a lot longer than one would think...)

Sound reasonable?
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

juggler

  • New Starter
  • Offline Offline
  • Posts: 1
Re: Going to make a box - what should I know?
« Reply #70 on: August 21, 2012, 03:57:58 PM »

Bergflodt's site was very inspirational to me also...what a craftsman.  My problem with his site is it made me really, really, want something I cannot have, a laser engraver.

If anyone really really wants to have some parts laser cut then get in touch. They are fabulous machines, but do have their limitations.

Squeezy - you have done me favours in the past, time for me to repay!

Ben
Logged
Pages: 1 2 3 [4]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal