Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Hohner 4 stop mod  (Read 4429 times)

0 Members and 1 Guest are viewing this topic.

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Hohner 4 stop mod
« on: June 09, 2011, 10:51:17 AM »

I have been going to fix the falling stop problem on my Hohner 1 row for some while now and was inspired by a mechanism I saw on a Marc Serafini box at Stowmarket. His mech used high powered magnets with like poles facing each other to make a really smooth yet positive action. I messed around with this idea and tried to build it into the 1 row but just could not find enough room between the reed blocks, stop slides and the bellows.

So I have now installed my Mk. II version which is simpler and much easier to install. It still uses high powered magnets but just to provide friction:

1. I drilled pilot holes in the frame of the treble end at right angles to the stop rods.



2. Opened the first hole to 1/4", and inserted a magnet



3. Opened up the rest of the holes and placed a magnet in each hole. The more observant amongst you will see I split the frame slightly when opening up the holes, just adds to my need to by a bench drill for jobs like this.



4. Go to B&Q to buy 1/4 dowel to cap the holes.

The magnets provide plenty enough attraction to hold the stop in the up position but still allow the stops to operate easily.

Magnets obtained from HERE for 30p per magnet so total cost of mod is £1.20.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner 4 stop mod
« Reply #1 on: June 09, 2011, 11:36:11 AM »

Nice idea.  Did you consider drilling from the inside?   Would make a much neater job, but maybe not enough wood thickness.  I've heard of a similar idea using nylon grub screws instead of magnets to provide the friction.  Could bring the price of parts down drastically.  ;D
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Malcolm Austen

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 495
  • any old hohner
Re: Hohner 4 stop mod
« Reply #2 on: June 09, 2011, 01:44:57 PM »

Lester, you are going to put the rubber band and clothes peg industries out of business with your new fangled contraptions.
Logged
aka malodeon

baz parkes

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1894
    • All Blacked Up
Re: Hohner 4 stop mod
« Reply #3 on: June 09, 2011, 03:06:39 PM »

it be the devil's work....
Logged
On the edge of Cheshire's Golden Triangle, apparently...

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Hohner 4 stop mod
« Reply #4 on: June 09, 2011, 03:20:58 PM »

Nice idea.
 
Ta!

Quote

Did you consider drilling from the inside?   Would make a much neater job, but maybe not enough wood thickness. 

You are indeed right and if doing it again that is what I would do.

Quote

I've heard of a similar idea using nylon grub screws instead of magnets to provide the friction. 

The up side of the magnet solution is that they are self adjusting.

Tufty

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 855
  • Dino Bincis etc
Re: Hohner 4 stop mod
« Reply #5 on: June 09, 2011, 05:55:03 PM »

Lester, you are going to put the rubber band and clothes peg industries out of business with your new fangled contraptions.
I just use the ones (rubber bands) that the postman drops on the doorstep ;D
Logged

Martyn

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 455
  • Hohnerohner
    • Martyn White Melodeon Tuning and Repairs
Re: Hohner 4 stop mod
« Reply #6 on: June 12, 2011, 02:13:26 PM »

Nice idea.  Did you consider drilling from the inside?   Would make a much neater job, but maybe not enough wood thickness.  I've heard of a similar idea using nylon grub screws instead of magnets to provide the friction.  Could bring the price of parts down drastically.  ;D

I think this is the modification Theo was referring to.

It's one I thought of some time ago to overcome the slipping stops problem (at least I think it was my idea as I've never seen it used anywhere else).

It involves first removing the stops and screw, marking out and drilling small holes on the inside edge of the box, Tapping with a 4mm thread and inserting nylon grub screws.
This means the tension on the stops is fully adjustable and the stops move up and down really smoothly.

Also because of the small hole size there is no risk of splitting the wood or causing a structural weakness in the stop area.

Martyn
www.melodeonrepairs.co.uk
« Last Edit: June 12, 2011, 02:26:49 PM by Martyn »
Logged
'Anything from a small repair to a full restoration'.
www.melodeonrepairs.co.uk

OwenG

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 297
Re: Hohner 4 stop mod
« Reply #7 on: June 12, 2011, 02:26:55 PM »

I just use the ones (rubber bands) that the postman drops on the doorstep ;D

I like these new-fangled ideas, but being a traditionalist I too favour the GPO approach at the moment. On a technical note, do you put the band round the wooden stop itself or the [technical term] metal bit [/technical term]?
Logged

pgroff

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1827
Re: Hohner 4 stop mod
« Reply #8 on: June 12, 2011, 03:32:16 PM »

Hi Lester,

In my experience with the 2- to 4-stop Hohners ..... a cubic mm or two of sticky accordion reed wax on a toothpick, applied to the steel stop rod just above the accordion casework, from the outside of the accordion, usually gives just the right amount of friction/airtightness needed when the stops don't stay up. Not enough to be visible, not sticky enough to prevent the stop moving (assuming it was loose to begin with).  If needed to clean it off, you could take the box apart and wash the rod with solvent to remove it.

PG
Logged

Martyn

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 455
  • Hohnerohner
    • Martyn White Melodeon Tuning and Repairs
Re: Hohner 4 stop mod
« Reply #9 on: June 12, 2011, 06:04:52 PM »

Hi Lester,

In my experience with the 2- to 4-stop Hohners ..... a cubic mm or two of sticky accordion reed wax on a toothpick, applied to the steel stop rod just above the accordion casework, from the outside of the accordion, usually gives just the right amount of friction/airtightness needed when the stops don't stay up. Not enough to be visible, not sticky enough to prevent the stop moving (assuming it was loose to begin with).  If needed to clean it off, you could take the box apart and wash the rod with solvent to remove it.

PG


Sounds like a bit of a messy operation for a temporary fix to me. I think all manner of things would end up getting stuck to the wax and pulled into the holes. Should be easy enough to clean out with a pressure washer though  >:E

Martyn
www.melodeonrepairs.co.uk
Logged
'Anything from a small repair to a full restoration'.
www.melodeonrepairs.co.uk

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Hohner 4 stop mod
« Reply #10 on: June 12, 2011, 06:07:37 PM »

I've done the wax thing also with good results.  Not messy at all.  I did it because I was worried if it was that loose it wasn't sealing well at the rod hole.

pgroff

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1827
Re: Hohner 4 stop mod
« Reply #11 on: June 12, 2011, 06:08:33 PM »

Hi Martyn,

1) I don't melt the wax - just rub a tiny (invisible) amount of the wax at room temperature on the metal rod, using a toothpick.  No mess whatsoever, and only the tiniest part of the length of the rod becomes sticky in the least.

2) It's actually more than a temporary fix -- lasts for years.

edited to add

3) But as always, YMMV, more than one way to skin a cat etc.  I'm sure the other solutions suggested above worked also. :-)

PG

also edited to add:

Hi blafleur, our posts crossed.  Glad this works for you too, always worked for me since I first tried it on a very beat up "test" box 20 years ago.  Compared to "chair-loc" (and some piano techs used to use white vinegar on loose tuning pins!) and other possible solutions to a loose fit around the stops, I can think of many ways the accordion wax solution could be loosened again if that became necessary due to the stops becoming too stiff (heating the metal stop rod with a soldering iron, etc.).  Actually after treatment with *a little* wax, none of the Hohner melodeons I've had have ever needed tweaking either for loosening or for tightening around the stops.  But used with discretion, I think the wax solution is very reversible if needed.
« Last Edit: June 12, 2011, 06:23:54 PM by pgroff »
Logged

martin p

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 408
Re: Hohner 4 stop mod
« Reply #12 on: March 17, 2014, 11:48:18 PM »

Fascinating how these threads acquire a life of their own. Thanks for all the tips, I may try the wax method first.

On the question of tweaks to Hohner single row boxes, I noticed a friends box had a rubber stopper fitted under the handle of each spoon to limit movement to minimum needed to open the valve. They appeared to be simply stuck onto the base plate. Is this a Hohner improvement or somebody's DIY clever mod?
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Hohner 4 stop mod
« Reply #13 on: March 18, 2014, 07:21:23 AM »

Fascinating how these threads acquire a life of their own. Thanks for all the tips, I may try the wax method first.

On the question of tweaks to Hohner single row boxes, I noticed a friends box had a rubber stopper fitted under the handle of each spoon to limit movement to minimum needed to open the valve. They appeared to be simply stuck onto the base plate. Is this a Hohner improvement or somebody's DIY clever mod?

I fit rubber feet designed for electronic stuff under the handle of the spoons. Not so much as to restrict the movement but to quieten down the click as the spoon hits the casework.

http://www.maplin.co.uk/p/stick-on-feet-domed-bp58n

pikey

  • Addicted to squeezeboxes since 1975
  • Thread mod
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3364
  • If it moves, I'll squeeze it....
Re: Hohner 4 stop mod
« Reply #14 on: March 18, 2014, 08:20:16 AM »

But what do you do then for percussion????  ;)
Logged
Still squeezing after all these years.
Mostly on hohners , with a couple of Dinos and a smattering of anglos - and now a Jeffries duet
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal