Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: beginner  (Read 6303 times)

0 Members and 2 Guests are viewing this topic.

hirundine

  • Member
  • *
  • Offline Offline
  • Posts: 17
Re: beginner
« Reply #20 on: August 14, 2011, 11:37:56 PM »

I'm noticing nobody has suggested cutting the leather around the rivets?

If you need to remove the thumb strap because it's getting in the way of your thumb behind the keyboard, leaving a stub of leather and rivet is no better: it's likely to have sharp edges and give you a sore thumb.

Ah, yes. I see. Looking again, I can see de-riveting a better option. Funnily, it's not in the way for me? The strap, that is. My playing skills are limited; though, I'm picking up loads just being around the site. I might try decapitating then with a dremel? Then after, drill out if necessary? The leather looks like it would assist in protecting the enamelling. The leather on mine eventually wore soft, using neatsfoot oil. Of all the instruments, I've tooled around with for over 50yrs; the melodeon gives me, the player, the most satisfaction. Even if it is the one, I'm least skilled with. ........ still, rock on! Onward and upward, etc. ..... greetings and gratitude, to all helpers, cheers Jamie!  ;D
Logged
Jamie -Nelson, British Columbia, Canada.

Prestidigitator

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 448
  • Saltarelle, Hohner, Oakwood Baffetti
Re: beginner
« Reply #21 on: August 15, 2011, 10:25:41 AM »

No, the whole rivet drops out. Admittedly you're then left with two holes!  Some people are happy to live with this, or you can use a filling method of your choice. Personally I use a short length of close-fitting dowel glued in and trimmed off flush inside and out, a minimal application of fine filler to seal the end-grain of the dowel and a finish with fine glasspaper.  I  generally touch in with a spot of Indian ink and three coats or so of shellac varnish, cut back with T-Cut just as you would touching in a small paint repair on a car.  Depends how much work you want to do.

Thanks for your answers and also ukebert. Gives good ideas with and for, dealing with this when I get to it. I'm noticing nobody has suggested cutting the leather around the rivets? Which was one of my thoughts.

I should of course have said that my comments above refer to wooden fingerboards; with the few plastic-fingerboard Hohners I've had, I've just left the holes.........

I've taken the thumbstraps off 2 Ericas with plastic keyboards by the "drilling out the rivet" method. I didn't want to leave the holes, and happened upon some small round plastic blanking discs used for plugging bolt holes or some such purpose. They happened to be an exact fit for the holes, and seem to stay in place without glueing, although it wouldn't hurt to do so. They are quite wide and flat, and I don't notice them. As these plugs were given to me, I don't know precisely where they came from, but if anyone is interested to know, I can find out.

Picture link here-or not as the case may be.
http://cubeupload.com/im/Prestidigitator/P1000324.jpg
« Last Edit: August 15, 2011, 10:35:17 AM by Prestidigitator »
Logged

hirundine

  • Member
  • *
  • Offline Offline
  • Posts: 17
Re: beginner
« Reply #22 on: August 18, 2011, 10:10:57 PM »

On my newly-bought Erica, many years ago, I decided on an alternative form of vandalism, i.e. punching an eyelet into the thumbstrap itself, and putting a small round-headed screw into the back of the box. The strap folds back behind the fingerboard and the eyelet pushes onto the screw head to hold it in place.
Photo attached.
So the thumbstrap is still there to be used if anyone should want to, but stays well out of the way for sensible playing.

...... Right on!! .. i'm gonna' give this idea serious consideration.

Cheers
Jamie
----------
Logged
Jamie -Nelson, British Columbia, Canada.
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal