Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Hohner Mignon Rust  (Read 4735 times)

0 Members and 1 Guest are viewing this topic.

ron1

  • Member
  • *
  • Offline Offline
  • Posts: 41
Hohner Mignon Rust
« on: September 01, 2011, 05:48:48 AM »


i need to remove rust or tarnish from the reeds of my Hohner Mignon. I read on E-How that a dry cloth will do the job. "Huh, well I tried and it doesn't work"

So a compound or method that will not interfere with tuning please.
Logged

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Hohner Mignon Rust
« Reply #1 on: September 01, 2011, 05:59:14 AM »

On a neglected old Club I used a glassfibre burnishing brush - but you do have to be VERY meticulous about blowing away ALL the tiny fibre particles that will be shed.  Mind you, you've got to clean away all the stuff you clean off, anyway.  I found a fairly powerful workshop vacuum cleaner on "blow" worked well.  I don't, however, know if this would meet your not-interfering-with-tuning criterion - the Club was undergoing a complete rebuild anyway.

Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Hohner Mignon Rust
« Reply #2 on: September 01, 2011, 08:08:06 AM »

I use one of these:

http://www.maplin.co.uk/polishing-block-2109

to clean the top of the reeds, don't forget to support the reed with some shim whilst polishing. The inside of the reed is harder to do but less prone to rust, I use a scalpel blade to scratch the rust of gently.

As to "So a compound or method that will not interfere with tuning please." if there is significant rust removing it will change the tuning  :(

ron1

  • Member
  • *
  • Offline Offline
  • Posts: 41
Re: Hohner Mignon Rust
« Reply #3 on: September 01, 2011, 10:06:38 AM »

Seems I may end up paying for tuning anyway.

Lester, I read somewhere here that you supplied someone with a pcb block. Does that do the job of removing rust?

burnishing brush sounds harsh.
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Hohner Mignon Rust
« Reply #4 on: September 01, 2011, 10:14:03 AM »

Seems I may end up paying for tuning anyway.

Lester, I read somewhere here that you supplied someone with a pcb block. Does that do the job of removing rust?

burnishing brush sounds harsh.


That is what I linked to above from Maplins

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Hohner Mignon Rust
« Reply #5 on: September 01, 2011, 11:19:40 AM »

burnishing brush sounds harsh.

Not at all; it does what it says - burnishes, a job which is traditionally done with a smooth metal tool (called a burnishing iron or just a burnisher) and imparts a smooth, polished surface with an absolute minimum of abrasion.  Exactly what the aforementioned pcb block does - it burnishes the copper.
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Andrew Wigglesworth

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1101
  • 07
    • My website
Re: Hohner Mignon Rust
« Reply #6 on: September 01, 2011, 11:35:45 AM »

On a neglected old Club I used a glassfibre burnishing brush - but you do have to be VERY meticulous about blowing away ALL the tiny fibre particles that will be shed.  Mind you, you've got to clean away all the stuff you clean off, anyway.  I found a fairly powerful workshop vacuum cleaner on "blow" worked well.  I don't, however, know if this would meet your not-interfering-with-tuning criterion - the Club was undergoing a complete rebuild anyway.

Graham

Wouldn't it be better on suck? I don't think that I'd like that mixture of glass fibre dust and rust blowing around in the air.

You'd have to keep a good grip on your tools, though   ;D

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner Mignon Rust
« Reply #7 on: September 01, 2011, 11:39:59 AM »

Yes the glass fibre dust is very irritating to the (human) airways.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Hohner Mignon Rust
« Reply #8 on: September 01, 2011, 02:42:49 PM »

Which is why I wear a good filter mask (not one of those cheap white DIY shop things in a pack of 5 for a quid or two) and have efficient dust extraction. My workshop is basically set up for woodworking and I'm well aware of the perils of fine sawdust etc.  Yes, in a workshop without extraction it would probably be safer on suck, but less efficient at removing the particles.
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Hohner Mignon Rust
« Reply #9 on: September 01, 2011, 07:06:46 PM »

The block that Lester mentions works a treat. I was able to use a piece of the block to clean the underside of my last set of reeds. The block slices fairly easily into a thin piece just narrow enough to fit into the reed chamber (valve removed). It helps to use a pinger to support the tongue and belly of the reed while you work the block piece back and forth since it's the only way to get to the tip of the reed tongue. Blow out the bits before pulling out the pinger and you're much less likely to have bits get stuck in the tongue.

Lester has a page of photos showing how to use the block.

Ed
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Christopher K.

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 894
Re: Hohner Mignon Rust
« Reply #10 on: September 01, 2011, 09:02:07 PM »

The block that Lester mentions works a treat. I was able to use a piece of the block to clean the underside of my last set of reeds. The block slices fairly easily into a thin piece just narrow enough to fit into the reed chamber (valve removed). It helps to use a pinger to support the tongue and belly of the reed while you work the block piece back and forth since it's the only way to get to the tip of the reed tongue. Blow out the bits before pulling out the pinger and you're much less likely to have bits get stuck in the tongue.

Lester has a page of photos showing how to use the block.

Ed

Ed, were you able to find a source for the rust removing product in the US or did you have to find it elsewhere? I have some problematic rust-spotted reeds to clean in an old club!

ron1

  • Member
  • *
  • Offline Offline
  • Posts: 41
Re: Hohner Mignon Rust
« Reply #11 on: September 01, 2011, 10:34:47 PM »


Thanks Ed for comments about pcb block. That will be my first choice, although i am tempted to Graham's burnishing. Maybe I'll try both..... given time. I take the point about dust and could not open windows, due to my interfering, no good cat, who will be banned from the room when repairs are attempted.

Lester, sorry I missed you link for Maplins. Thanks for pointing me in the right direction. By the way, I loved your website.

 :||: Ron
Logged

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Hohner Mignon Rust
« Reply #12 on: September 01, 2011, 10:41:36 PM »

Ed, were you able to find a source for the rust removing product in the US or did you have to find it elsewhere? I have some problematic rust-spotted reeds to clean in an old club!

Christopher, if you have problems sourcing this (who the devil took over Radio Shack in the US?) PM me your details and I'll mail one to you. That will be a one time offer!  ;)
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

AirTime

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 979
Re: Hohner Mignon Rust
« Reply #13 on: October 23, 2011, 06:04:43 PM »

I have just picked up an old (ca. 1910?) one-row Hohner. The reeds look to be rust-free, but I'm looking to clean up the oxidation & rust from the external hardware. Also tips for cleaning up the bellows & woodwork would also be appreciated. Thank you for any suggestions!
Logged
1920's BbEb Hohner; 1920's  AD Koch; 1910 (?) One-row Hohner in D,  1910's GCB Maga Ercole; ; AD 1950's Pistelli, CF Sandpiper, CF Preciosa, BbEb Preciosa.

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Hohner Mignon Rust
« Reply #14 on: October 23, 2011, 06:15:37 PM »

I've had good luck with this. http://www.leevalley.com/US/wood/page.aspx?p=58771&cat=1,190,43040,58771

I soak it a day, and it does a good job of removing the rust, but it does need a rinse in a solvent to remove before revalving and reinstalling.  Good thing about a chemical rust remover is it gets the nooks and crannies that you just can't get to with gadgets.

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Hohner Mignon Rust
« Reply #15 on: October 23, 2011, 07:28:35 PM »

I was given the name "Garryflex" for the abrasive blocks, by a concertina guru - looks and works the same. He uses the finest grade. Axminster tools sell it. Dunno how it compares with Maplin. 
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Hohner Mignon Rust
« Reply #16 on: December 20, 2011, 04:42:13 AM »

You can get Rubber polishing wheels for a dremel tool that polish the rust off. A pencil eraser will work for light rust. I slide a shim behind the reed for support. You want to have the wheel rotating from the base to tip of the reed so you don't snag and ruin the tips of the smaller reeds.
 This takes practice.
You may also try 2500 grit sand paper wrapped around the end of your finger with the reed supported from behind by a shim polish from bass to tip. The reeds will almost certainly need to be tuned afterwards.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal