Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: Leather and felt for pallets  (Read 12255 times)

0 Members and 1 Guest are viewing this topic.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Leather and felt for pallets
« Reply #20 on: September 10, 2024, 10:57:49 AM »

If you were to leave out one component of the felt/leather pallet facing you should leave out the felt.  Felt is not airtight so if airtightness is the priority then leather on it's own will give a better seal than felt on it's own.  Any soft leather will do.  If you have access to a leather supplier ask for "sheep nappa, its a leather produced for clothing so is widely available in the leather trade.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Leather and felt for pallets
« Reply #21 on: September 10, 2024, 12:14:46 PM »


- It's missing the two pokerworks style "eyelets" that hold on the metal grill. If anyone knows what size these are so I can order from a diy shop somewhere now CGM isn't around, that would be very helpful)
What I do is go to B&Q and buy the smallest cup hooks they have then bend the cup around to for a circle
https://www.diy.com/departments/metal-j-shaped-single-hook-w-11mm-pack-of-10/240705_BQ.prd

Sebastian Trudgian

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 124
  • DG Pokerworks and also play Irish Whistle/Flute
Re: Leather and felt for pallets
« Reply #22 on: September 10, 2024, 02:24:53 PM »

Great thanks Theo and Lester.
I'll try and find a leateher person and get some "sheep napa" and look in B&Q for small J hooks I can bend.

Thankyou.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Leather and felt for pallets
« Reply #23 on: September 10, 2024, 02:33:10 PM »

You can just use wood screws. They don’t look right but will at least make the grill secure.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Aaron Wildman

  • Member
  • *
  • Offline Offline
  • Posts: 36
Re: Leather and felt for pallets
« Reply #24 on: September 10, 2024, 05:58:31 PM »

Leather will seal much better than felt.  In the states, I buy mine premade from Bosco accordions on eBay.  It is important to note that there are various thicknesses, and changing the thickness will change the angle your pallet closes, causing leakage.  Bending levers etc is important to make sure your newly-faced pallets seal properly.  Don't bend unless it is necessary, but do bend if you need to seal properly.
Logged

JohnJ

  • Member
  • *
  • Offline Offline
  • Posts: 26
    • JJ's Stuff
Re: Leather and felt for pallets
« Reply #25 on: February 14, 2026, 11:07:41 AM »

I'm looking to reduce the 'clack' on my old (50+ years) Pokerwork.
The facing on the pallets seal perfectly, but I can't see any felt backing on the leather - although it may just be so compressed after 5 decades of squeezing that it's no longer visible.
Recommendations on here suggest replacing the pallet facing with nappa leather, backed with thin felt.
Can anyone advise what sort of thickness materials I should be using - and maybe a source of either ready bonded nappa & felt, or nappa and felt separately.
Thanks!
Logged
Hohner B/C, D/G, & A/D/G, & Maestro D/G

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Leather and felt for palletsgso
« Reply #26 on: February 14, 2026, 12:00:15 PM »

So there are a couple of things to note. 1) Hohner originally faced the pallet with a soft leather…not with a leather felt sandwich. This was good enough when it was made and for ease of replacement would probably be good enough now. 2) if you strip off the old leather and replace it with new soft leather it will go back together and not mess up the button height. 3) it is kind of 'the law' on here to always face pallets with a felt/leather sandwich, which does indeed quiet clackiness. But (think about it) the buttons end up being lowered and you may need then to reset them, which isn't *that* hard but can be tricky..the buttons tend to go off centre so getting it all to feel and look right takes some work. 4) whatever you do you have to remove and refit the pallets. Only glue/fix them *after you have dry fitted them and fiddled until there are no air leaks. Don't just assume it is leak free. I guarantee it won't be if you don't check it.
My personal take on this is ..if it was good enough to just use a leather strip when it was made, then surely it is good enough now? Plus it is a much simpler job (and materials easier to obtain) than fitting a felt/leather sandwich. Which is not to say the felt/leather sandwich is not better, and perhaps it is the way to go..but it is more involved. You can buy suitable soft leather on eBay. I used to get my from Pittards but sadly they closed a couple of years ago.
« Last Edit: February 14, 2026, 12:05:01 PM by Rog »
Logged

JohnJ

  • Member
  • *
  • Offline Offline
  • Posts: 26
    • JJ's Stuff
Re: Leather and felt for pallets
« Reply #27 on: February 14, 2026, 12:09:02 PM »

Thanks Rog, that's kind of what I was thinking - I was concerned that the potential for things to go wrong would be much greater using a felt & leather 'sandwich' than leather alone.
Could you advise on the thickness of nappa I should be using.
Thanks.
Logged
Hohner B/C, D/G, & A/D/G, & Maestro D/G

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Leather and felt for pallets
« Reply #28 on: February 14, 2026, 01:44:58 PM »

Not really. Maybe a 1mm or 1.5mm. I don't buy in by thickness. I'd probably buy something like this. Use a rotary cutter..much easier than a knife.
https://ebay.us/m/3Ru39b
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal