Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: How to bush bass buttons  (Read 7696 times)

0 Members and 1 Guest are viewing this topic.

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
How to bush bass buttons
« on: September 13, 2011, 07:51:56 PM »

I've misplaced my Dave Elliot book (packed away in a box somewhere) and would rather spend my limited shop time actually bushing the bass buttons on my Erica rather than looking for the book.

I ran into a web page with Bob Tedrow's method of bushing the holes in concertina buttons but that didn't quite sound right for a bass button hole. I think I'm supposed to use a tapered reamer to ream the hole to a bit larger size. I have vague memories of photos of cutting the 1mm felt to a wedge shape and doing a bit of a twist around a tapered dowel that matches the taper of the reamed hole. Is that right? Bob's method was to have a straight butt joint for the felt rather than a tapered spiral, if that makes sense.

Does anyone have photos of the process?

Thanks,

Ed
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

waltzman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 943
Re: How to bush bass buttons
« Reply #1 on: September 13, 2011, 09:08:50 PM »

I took a much simpler (and fully-reversible-if-you-don't-like-the-result) approach with my Erica bass buttons.  I got some 1mm thick felt that was self adhesive and cut long strips about 2mm wide.   Two lengths of these strips were placed about 30 degrees apart at the 'high side' of the hole for the bass buttons on the Erica.  I took the long strip and carefully fed it down between the button and the side of the hole and then pressed it against the side of the hole to make it stick and trimmed it with a small scissors at the top edge of the hole.  This eliminated the button rattle and does not interfere with the buttons moving up and down at all.  I've been quite pleased with the result.
Logged

Cooper

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 705
  • Gaillrd G/C/#,Casta Allain8 GC,Lofft CF, giord ad
    • Cooper's homepage
Re: How to bush bass buttons
« Reply #2 on: September 14, 2011, 12:55:31 AM »

I've misplaced my Dave Elliot book (packed away in a box somewhere) ...

I think perhaps some people better leave their boxes closed, and leave the repairwork to pro's,
;-)
W
Logged
Please correct my English, it's been a while, and i like to learn.
And don't be so polite! I know i must be typing tons of stuff that a native speaker would say differently...please enlighten me.

www.wouterkuyper.nl
www.lirio.nl
www.trekzakacademie.nl

Christopher K.

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 894
Re: How to bush bass buttons
« Reply #3 on: September 14, 2011, 01:35:36 AM »

Be careful to avoid splitting the bench while using the taper file. I have a few accordions with hairline cracks in the benches that are hard to spot unless under a very bright light.

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: How to bush bass buttons
« Reply #4 on: September 14, 2011, 07:33:49 AM »

I have yet to do this job on an Erica but have done it successfully on a few Pokerworks. My method is to open up the holes in the casework with a tapered reamer then to line the holes with proper bushing felt. I have not found the need to do any fancy tapering of the felt just to fiddle around until the butt joint is "just so" with a dry fit. I then use PVA glue around the holes and then roll felt up into a tight roll insert it in the hole and use a screwdriver blade to seat the felt it in the glue.

As to an Erica I think the job will be harder as the holes are not square to to the casework and am contemplating buying a parallel reamer, I am also worried about the celluloid chipping but only time will tell.

I get my bushing felt from Dave Leese http://www.concertina-spares.com/spareslist.htm. As he notes it is important to use the felt cut "on the bias" to prevent fraying hence it is supplied in a trapezoidal shape.

Prestidigitator

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 448
  • Saltarelle, Hohner, Oakwood Baffetti
Re: How to bush bass buttons
« Reply #5 on: September 14, 2011, 08:30:11 AM »

I was given some "printing felt" which is used as a cushion or blanket in etching or intaglio printing presses, and thus has to resist immense pressures frequently applied. It's about 5mm thick, very dense and comes in hard and soft versions. I've used it for various pads and bushes, the latter made with wad punches to make one-piece bushing rings, rather than cutting out strips. I've yet to find a use for the waste centre punchings, other than keyboard attachment screw washers. It seems to be pretty durable.

The downside of this felt is that it is very expensive to buy, with a piece 34cm x 90cm (a standard size) costing £40; which does have the benefit of ensuring that I follow the "measure twice, cut once" principle.
Logged

Christopher K.

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 894
Re: How to bush bass buttons
« Reply #6 on: September 14, 2011, 09:48:25 AM »

Quote
As to an Erica I think the job will be harder as the holes are not square to to the casework and am contemplating buying a parallel reamer, I am also worried about the celluloid chipping but only time will tell.

I missed the part about how you're modifying an Erica. Ignore my gibberish about cracked benches unless you get around to doing a Pokerwork or something similar, as the Erica of course has no bench.

Graham W

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 277
Re: How to bush bass buttons
« Reply #7 on: September 14, 2011, 09:54:19 AM »

I'm always intrigued that Taper reamers are mentioned whenever bushing bass buttons comes up.

I'm not a melodeon repairer, just a woodworker with an interest in engineering who enjoys fiddling with and mending things, but it strikes me that if the hole is left tapered it will only be the dia you want at one small point - thus reducing the bearing area that is supporting the shaft of the button. The bush won't last as long as it could because all the pressure will be on a small area of felt, not on the whole depth of the hole. (Whether this is actually a problem is debateable though!)

Increasing the size of holes in wood by just a litttle is not easy to do neatly.  If a taper hand reamer is all you have then it is tricky, especially not to end up with a slightly oval hole - you really need to ream the hole from both the insdie and outside of the box which leaves you with an hourglass shape, then use a rat tail file to take out the waste to leave a parallel hole.

Parallel reamers do have a taper lead to get them into the hole in the first place, but you really need to run them very accurately square to the hole - ideally mounted in a good solid drill press or milling machine.

Then again - these reamers aren't designed for cutting wood, and come in various different types,  so scope for experimentation to see what works best. 
If you have access to a very rigid bench drill or mill then it is possible to open out holes with successively larger drill bits as long as they are very sharp and you only take a little out each time.  This won't work well if there is any wobble at all on the chuck of your machine.

There - another job that's trickier than it looks at first sight ;D
What's your approach Theo?
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: How to bush bass buttons
« Reply #8 on: September 14, 2011, 11:07:31 AM »


What's your approach Theo?

i I use a taper reamer designed for cutting wood.   I think it's intended use is to ream violin peg holes.  It has 3 or 4  cutting flutes that run down one side and the remainder is smooth.  I think this part of the design means it will cut an accurate circular hole in wood.   The taper is very gradual so I've never found the tapering hole to be a problem.  Bushing cloth is actually a woven woolen fabric with felted surfaces and is very hardwearing in this application.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Andy Simpson

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 938
Re: How to bush bass buttons
« Reply #9 on: September 14, 2011, 01:14:02 PM »

I use a cello peg reamer, works very well but very expensive.

A straight strip often works just fine but ideally the bushing should be cut in a rhomboid shape, (NOT a trapezoid).

The Erica is probably the trickiest common model to bush the bass buttons on due to the slant that leaves a hole with one side considerably higher than the other. Cutting the cloth straight or in a rhomboid you can either only do the bushing as high as the lowest side of the hole, which doesn't look very nice IMO, or have it full height and then trim it down to match the slant of the cabinet afterwards, which is more work and presents it's own set of problems. My approach was to make the bushes full height in a trapezoidal shape with the longer side on top and shorter underneath, keen students of geometry will immediately realise that lining a round hole with that shape will leave a triangular gap and you're still left with the bushing sticking out above the low side of the hole. However, if you've done it right then you can push the ends together to close that gap and one side will dip lower, leaving you with a fully lined hole and a bush that's level with the slanting surface. (:)
Logged

Martyn

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 455
  • Hohnerohner
    • Martyn White Melodeon Tuning and Repairs
Re: How to bush bass buttons
« Reply #10 on: September 14, 2011, 01:37:19 PM »

It's also a good idea to cover the holes with a couple of layers of masking tape before using the reamer. This will help prevent chipping of the celluloid and will also prevent splitting of the bass 'step' on pokerworks and the like.

Martyn
Logged
'Anything from a small repair to a full restoration'.
www.melodeonrepairs.co.uk

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: How to bush bass buttons
« Reply #11 on: September 14, 2011, 06:09:30 PM »


I use a taper reamer designed for cutting wood.   I think it's intended use is to ream violin peg holes.  It has 3 or 4  cutting flutes that run down one side and the remainder is smooth.  I think this part of the design means it will cut an accurate circular hole in wood.   The taper is very gradual so I've never found the tapering hole to be a problem.  Bushing cloth is actually a woven woolen fabric with felted surfaces and is very hardwearing in this application.

Yes, this kind of taper reamer is designed for violin peg holes. I have one and used it for reaming the peg holes for lutes when I studied stringed instrument making many, many years ago. The smooth side keeps the hole from going out of round but also allows you to drift the ream in one direction or the other in order to reset the center of the hole.

As with reaming any hole in a thin piece of wood the pressure is light and the effort goes into the cut, not into shoving the reamer into the hole - that's the way to get the cracks that Christopher K. mentioned.

If I am using 1mm thick felt from David Leese (I have some) how much larger to I ream the hole? 2mm larger than the button diameter? Less? I think I read somewhere that you're supposed to use a tapered dowel to compact the felt. Is that right?

Ed
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Andy Simpson

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 938
Re: How to bush bass buttons
« Reply #12 on: September 14, 2011, 06:19:26 PM »

Use the diameter of the button +2mm as a rule of thumb. To get a proper fit you really have to do it by feel.
Logged

Bill Young

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1151
  • Paolo Soprani BCC#
Re: How to bush bass buttons
« Reply #13 on: September 15, 2011, 09:19:14 AM »

How do you get the buttons out of the holes, in order to bush them, on an Erica/Double Ray? Remove the whole bass mechanism, with buttons and rods, in a one-er; or remove the buttons and rods individually?
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: How to bush bass buttons
« Reply #14 on: September 15, 2011, 09:31:46 AM »

How do you get the buttons out of the holes, in order to bush them, on an Erica/Double Ray? Remove the whole bass mechanism, with buttons and rods, in a one-er; or remove the buttons and rods individually?

Yes either of those.

Both methods have their drawbacks. 

Removing the rods requires removing the small bent pin that acts as a pivot,   if you re-use the originals they will be weakened and there is a risk of them breaking.  If you use new pins then finding the right diameter pin can be tricky.

Removing the whole mechanism requires removing the buttons first if they are mushroom buttons as on pokerworks, or on Erica type there is not quite enough space to get the entire mechanism out without bending some levers.  Then release all springs and remove screws.

I prefer the second method because getting the whole mechanism out of the way allows me to give the inside a good clean to get out all the dust and fluff (and worse!) that tends to get trapped under and around the mechanics.  It is also easier to check springs and replace if required.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Martyn

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 455
  • Hohnerohner
    • Martyn White Melodeon Tuning and Repairs
Re: How to bush bass buttons
« Reply #15 on: September 15, 2011, 09:38:30 AM »

How do you get the buttons out of the holes, in order to bush them, on an Erica/Double Ray? Remove the whole bass mechanism, with buttons and rods, in a one-er; or remove the buttons and rods individually?

I find the easiest and quickest method is to remove the L shaped pins and slide the rods out through the button holes. The pins can usually be re-used but if they do break or become weakened, just cut down a veneer pin of the same diameter.
It is always a good idea to number them too.

Martyn
« Last Edit: September 15, 2011, 09:44:27 AM by Martyn »
Logged
'Anything from a small repair to a full restoration'.
www.melodeonrepairs.co.uk

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: How to bush bass buttons
« Reply #16 on: September 15, 2011, 10:09:49 AM »

How do you get the buttons out of the holes, in order to bush them, on an Erica/Double Ray? Remove the whole bass mechanism, with buttons and rods, in a one-er; or remove the buttons and rods individually?

I find the easiest and quickest method is to remove the L shaped pins and slide the rods out through the button holes. The pins can usually be re-used but if they do break or become weakened, just cut down a veneer pin of the same diameter.
It is always a good idea to number them too.

Martyn

I'm with Martyn, but I always replace the pins with veneer pins I got at B&Q, save grief later if the original fails which is fairly common in my world.

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: How to bush bass buttons
« Reply #17 on: September 15, 2011, 12:26:41 PM »

Removing the whole mechanism requires removing the buttons first if they are mushroom buttons as on pokerworks,

I don't have any real problems removing mushroom buttons, but I find them the very devil to replace with new ones (old ones obviously go back on more easily). The most successful method I've tried is very gently easing the hole with a twist drill just a shade bigger than the existing hole - and even then I find them a struggle to fit and have broken one or two.  Any suggestions (probably something glaringly obvious that I haven't thought of!)?

Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: How to bush bass buttons
« Reply #18 on: September 15, 2011, 12:31:19 PM »

Removing the whole mechanism requires removing the buttons first if they are mushroom buttons as on pokerworks,

I don't have any real problems removing mushroom buttons, but I find them the very devil to replace with new ones (old ones obviously go back on more easily). The most successful method I've tried is very gently easing the hole with a twist drill just a shade bigger than the existing hole - and even then I find them a struggle to fit and have broken one or two.  Any suggestions (probably something glaringly obvious that I haven't thought of!)?

Graham

I use judical application of heat to the metal part using my big soldering iron then press the rod into the button.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: How to bush bass buttons
« Reply #19 on: September 15, 2011, 01:01:42 PM »

or enlarge the hole with a small screwdriver of slightly less width than the rod.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal