Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: How to bush bass buttons  (Read 7690 times)

0 Members and 1 Guest are viewing this topic.

Martyn

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 455
  • Hohnerohner
    • Martyn White Melodeon Tuning and Repairs
Re: How to bush bass buttons
« Reply #20 on: September 15, 2011, 02:33:44 PM »

I just put the button on the bench with the hole facing upwards, grip the rod in the pliers as close to the button as possible and push it in. This usually works without the need to enlarge the hole or apply heat.

Martyn
Logged
'Anything from a small repair to a full restoration'.
www.melodeonrepairs.co.uk

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: How to bush bass buttons
« Reply #21 on: September 15, 2011, 02:57:17 PM »

Well, more than one way to skin a cat, eh?  I'd thought of heat to soften the plastic, but didn't fancy the idea of a hot iron or a mini-blowtorch flame that close to the woodwork!  I like the button-on-the-bench approach; it should spread the stress on the button more evenly. Next time I have replace some......

Thanks all.

Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Stiamh

  • Old grey C#/D pest
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3611
    • Packie Manus Byrne
Re: How to bush bass buttons
« Reply #22 on: September 15, 2011, 04:10:39 PM »

... judic(i)al application of heat ...

Sounds like a case for the European Court of Human Rights  :D

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: How to bush bass buttons
« Reply #23 on: September 15, 2011, 05:19:44 PM »

How do you get the buttons out of the holes, in order to bush them, on an Erica/Double Ray? Remove the whole bass mechanism, with buttons and rods, in a one-er; or remove the buttons and rods individually?

I found I could get the bass mechanism on my Erica out without bending the rods if I first release the springs and remove the screws. You can then slide the axle plate sideways to get one set of four buttons out, slide the other direction to get the other four out. Takes a bit of work to do it but I did not end up bending the rods.

I was surprised to find that though my Erica and Preciosa both have a slanted bass button boards, the Erica has the holes drilled parallel to the soundboard while the Preciosa has the hole drilled perpendicular to the button board. The bass button on the Preciosa moves parallel to the soundboard, same as the Erica so the hole orientation doesn't make sense to me. Has that been your experience Theo?

Ed
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: How to bush bass buttons
« Reply #24 on: September 15, 2011, 05:25:06 PM »

"bass button on the preciosa moves parallel to the soundboard". Not my experience, the buttons are usually parallel to the axis of the holes,  though the rods they are mounted on are not.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: How to bush bass buttons
« Reply #25 on: September 15, 2011, 05:32:14 PM »

"bass button on the preciosa moves parallel to the soundboard". Not my experience, the buttons are usually parallel to the axis of the holes,  though the rods they are mounted on are not.

Hmm, I'll have to look at that again when I get the mechanism back into the bass side. I have the mechanism out for cleaning the soundboard and for taking measurements for drawing plans of the instrument.
« Last Edit: September 15, 2011, 05:34:10 PM by Telemorris »
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: How to bush bass buttons
« Reply #26 on: September 16, 2011, 09:38:23 AM »


Hmm, I'll have to look at that again when I get the mechanism back into the bass side. I have the mechanism out for cleaning the soundboard and for taking measurements for drawing plans of the instrument.

Regarding the photo of the bass end, I've never come across that fancy double air-release linkage before.
Well, you learn something every day.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal