Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 ... 3 4 5 6 7 [8] 9 10 11 12 13 14   Go Down

Author Topic: The 21st Century Box  (Read 108218 times)

0 Members and 1 Guest are viewing this topic.

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11153
  • Wirral UK
    • Chris Ryall
Re: The 21st Century Box
« Reply #140 on: June 12, 2012, 08:14:48 AM »

Sadly they don't seem to get to Ch. d'Ars. I was tempted to go Maastricht way (looks a very nice place for a weekend) and have a go. But I suspect the keyboard layout might blow my brains out ... http://www.bandoneon-maker.com/keyboardlayoutband.htm
Logged
  _       _    _      _ 

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: The 21st Century Box
« Reply #141 on: June 12, 2012, 08:26:51 AM »

Sadly they don't seem to get to Ch. d'Ars. I was tempted to go Maastricht way (looks a very nice place for a weekend) and have a go. But I suspect the keyboard layout might blow my brains out ... http://www.bandoneon-maker.com/keyboardlayoutband.htm

It`d certainly blow mine hence being more interested in the Unisonoric versions . also I edited my post above, there aren`t any 800 Euro Bi-sonoric ones, read again, 800Euros is for a fancy bellows option, the cheapest is the Student at 2300 :(
Logged
Q: How do you cure MAD?
A: Buy more Boxes

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11153
  • Wirral UK
    • Chris Ryall
Re: The 21st Century Box
« Reply #142 on: September 30, 2013, 10:54:52 AM »

New development on the micrphone wiring front  this post is simply a link. click link, or picture below if you want to contribute to the new thread.

As mentioned this stage was a bit of a surprise for me; when nudiefish asked me to fit a “mike system” I just said, “yes” without thinking much about it.
When I came to start to fit it I came to the very fast conclusion that I had never put one into this smaller size box (240mm x 150mm) that had 12 bass and slides, this causes the reed blocks to take up every last mm within the bellows cavity giving me very little room to move for the cabling down the inside of the bellows, eventually after a very frustrating day I got there with it.

Because of the 12 bass in such a small box I even had to put the stereo socket in a place where I would not normally do so, this time I had to have it fit within the bass mechanism rather than bellow it.
If I ever have to do this again on this size box, then I would run the first half of the cabling across the back folds then revert to the top for the next half.
After the initial frustration it works very well.

This interested me as the cabling looked very fiddly and I got to thinking why not create a frame (maybe thin aluminium to keep weight down) that sits inside the bellows to center the cable and then use a spiral cable that would expand with the bellows. I tried to create a small drawing to illustrate whet I mean. Putting plugs on both ends of the cable, to connect with sockets in the reed boxes would help with tuning to detach the bellows completely.

Logged
  _       _    _      _ 

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11153
  • Wirral UK
    • Chris Ryall
Re: The 21st Century Box
« Reply #143 on: December 14, 2013, 11:16:01 AM »

Just to post a link to Chris Brimley's idea on interval based keyboards

  http://forum.melodeon.net/index.php/topic,13761.0/topicseen.html

"thinking outside the box" - like that title!
Logged
  _       _    _      _ 

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: The 21st Century Box
« Reply #144 on: December 14, 2013, 11:10:36 PM »

New development on the micrphone wiring front  this post is simply a link. click link, or picture below if you want to contribute to the new thread.

As mentioned this stage was a bit of a surprise for me; when nudiefish asked me to fit a “mike system” I just said, “yes” without thinking much about it.
When I came to start to fit it I came to the very fast conclusion that I had never put one into this smaller size box (240mm x 150mm) that had 12 bass and slides, this causes the reed blocks to take up every last mm within the bellows cavity giving me very little room to move for the cabling down the inside of the bellows, eventually after a very frustrating day I got there with it.

Because of the 12 bass in such a small box I even had to put the stereo socket in a place where I would not normally do so, this time I had to have it fit within the bass mechanism rather than bellow it.
If I ever have to do this again on this size box, then I would run the first half of the cabling across the back folds then revert to the top for the next half.
After the initial frustration it works very well.

This interested me as the cabling looked very fiddly and I got to thinking why not create a frame (maybe thin aluminium to keep weight down) that sits inside the bellows to center the cable and then use a spiral cable that would expand with the bellows. I tried to create a small drawing to illustrate whet I mean. Putting plugs on both ends of the cable, to connect with sockets in the reed boxes would help with tuning to detach the bellows completely.


Instead of leading the cable straight from one end to the other across the bellows, it would be much better to make it go top to bottom as well. Then the ratio between stretched and unstretched length is much less, and you wouldn't need any frame -- just attach it to (for example) the inside top of the bass end and the inside bottom of the treble end (where the reed blocks are less tall).
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: The 21st Century Box
« Reply #145 on: December 15, 2013, 02:25:16 PM »

Having short arms I wouldn't expect to get the coil trapped in the bellows folds but you would have to play rather sedately to avoid the coil slapping against the sides.  I get enough bellows noise when playing a Pokerwork standing up, fast direction changes seem to slam all the corners into each other.  I guess some interim supports across the bellows would prevent this but each refinement adds weight and possibly inflexibility.  A serpentine wire tacked at the midpoint of each fold to the inner folds of the bellows works very well (still needs a connector each end).  Actually, if Castagnari can accept bellows pins one end only (Lilly and Tommy), then maybe a single connector will suffice.

Rob.
Logged

denj.jones

  • New Starter
  • Offline Offline
  • Posts: 2
  • 25 melodeons,1bandoneon 4flutina,4concertinas
Re: The 21st Century Box
« Reply #146 on: December 16, 2013, 08:22:22 PM »

Having repaired/restored/re tuned several melodeons and accordions for over 20 years now, i am keen to find other views on the topic of sealing reed blocks/plates.
I have found much success in using window frame or bathroom sealant,which in my opinion offers more advantages than the traditional wax methods.
eg it does not age(go brittle),does not melt or soften in high ambient temp, is easier to apply,etc, etc
please forgive me if this has been a well debated topic in the past, (my first contribution) :P
Den Jones Wirral
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: The 21st Century Box
« Reply #147 on: December 16, 2013, 08:23:39 PM »

I think that post should be deferred to April 1st.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

denj.jones

  • New Starter
  • Offline Offline
  • Posts: 2
  • 25 melodeons,1bandoneon 4flutina,4concertinas
Re: The 21st Century Box
« Reply #148 on: December 16, 2013, 08:47:13 PM »

thank you for your your considered view, i was hoping for a little more enlightenment on the subject of 21st century design/ construction though.I am willing to accept any criticisms but would much like to hear of pros and cons
many thanks den
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: The 21st Century Box
« Reply #149 on: December 16, 2013, 08:50:52 PM »

thank you for your your considered view, i was hoping for a little more enlightenment on the subject of 21st century design/ construction though.I am willing to accept any criticisms but would much like to hear of pros and cons
many thanks den

More considered an opinion than mine would have been having had to remove reed plates stuck in with things other than proper reed wax. It should be a capital offence.

Bob Ellis

  • Hero?....Where's my medal, then?
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2878
  • Ain't I cute?
Re: The 21st Century Box
« Reply #150 on: December 16, 2013, 09:03:42 PM »

With only the experience of having built one melodeon and done a bit of work on a couple more, I must say that I like Emmanuel Pariselle's preferred method of holding the reeds in place with a small screw in the centre of each side. This makes them easy to adjust and/or remove and improves the resonance of the reeds (or so I am told by those more knowledgeable than I am.)
Logged
Bob in beautiful Wensleydale, Les Panards Dansants, Crook Morris and the Loose Knit Band.
Clément Guais 3-row D/G/acc.; Castagnari 1914 D/G; Karntnerland Steirische 3-row G/C/F; Ellis Pariselle 2.6-row D/G/acc.; Gabbanelli Compact 2-row D/G with lots of bling, pre-war Hohner Bb/F; Acadian one-row in D.

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: The 21st Century Box
« Reply #151 on: December 16, 2013, 09:15:32 PM »

With only the experience of having built one melodeon and done a bit of work on a couple more, I must say that I like Emmanuel Pariselle's preferred method of holding the reeds in place with a small screw in the centre of each side. This makes them easy to adjust and/or remove and improves the resonance of the reeds (or so I am told by those more knowledgeable than I am.)

Only works on reed blocks made of close grained hard woods/fruit woods. You typical Hohner reed block would not hold a screw sufficiently firmly.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: The 21st Century Box
« Reply #152 on: December 16, 2013, 09:17:05 PM »

A more considered reply would be:

The requirements of a method if securing reeds to blocks is twofold: 1. The reeds need to be held rigidly in place and 2 it must be easy to remove reeds to replace broken tongues and perished valves.

Wax and screws both meet these requirements, thought wax does have some drawbacks : it can be messy to apply and it does have a limited life of only 30 years or do.  Screws are certainly superior, but you need hardwood reed blocks to give screws a reliable grip.

Silicone type window sealants fail on both counts.  The material is too flexible to hold reeds firmly enough to sound optimally, and it is the very devil to remove if a reed needs to be removed.

Like Lester I've had several cases where I silently cursed a previous repairer who fixed reed plates with window sealant.

Mind you the ones who use the stuff to fix bellows are the worst.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

MatthewVanitas

  • Good talker
  • **
  • Offline Offline
  • Posts: 94
  • Hohner HA-113A - HA-112D - D Chanson re-reed
Re: The 21st Century Box
« Reply #153 on: December 18, 2013, 05:08:48 PM »

Haha, just had a wacky idea. How about valves which are a composite with a low coercivity (soft magnetic). ...

I know the valve magnet idea may be a bit odd, there's at least one melodeon maker who's using rare-earth magnets in the stop knobs so that they'll stay up when pulled up. Kind of a clever way to avoid the seemingly-inevitable tendency of Cajun/Quebecois/Irish melodeon stops to either be sticky and too tight, or too lose and inclined to slide down and turn a bank on or off.
Logged

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11153
  • Wirral UK
    • Chris Ryall
Re: The 21st Century Box
« Reply #154 on: May 25, 2014, 06:43:37 AM »

I plan to continue to update this thread as new innovations arise. Here is Owen Woods' (Ukebert here) blog about his project to make a melodeon using CAD/CAM

  http://melodeonmusic.com/2014/05/20/joy-making/

Keep 'em coming …
Logged
  _       _    _      _ 

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11153
  • Wirral UK
    • Chris Ryall
BASS Chimney: 21st Century Box
« Reply #155 on: June 04, 2014, 01:32:59 PM »

THE "BASS CHIMNEY"  An Emmanuel Pariselle idea.

The notes in the chords on left end all sound at once, so why give them separate plumbing. Emmanuel "folds" the construction using space more efficiently, apparent this is a lft from Russian Bayan construction

See http://forum.melodeon.net/index.php/topic,14814.msg183242.html#msg183242 (includes pictures)

Thanks to Theo for clarification below. Essentially this makes for a 2 storey bass internally. I could add that the conventional bass blocks on my kit come close to touching, belows closed, so use of this might be "where feasible"
« Last Edit: June 04, 2014, 07:38:37 PM by Chris Ryall »
Logged
  _       _    _      _ 

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: BASS Chimney: 21st Century Box
« Reply #156 on: June 04, 2014, 04:58:07 PM »

The notes in the chords on left end all sound at once, so why give them separate plumbing.

Not quite correct, but an understandable misapprehension if you've not handled one.   There is one "chimney" per low bass reed, which is not shared with any other reeds.   The purpose of the chimney is to allow the low bass reeds to lie on top of the high bass and the chord reeds which are mounted conventionally.

Marc Serafini also uses this method in some of his designs.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11153
  • Wirral UK
    • Chris Ryall
21st Century Box - phase advancing cross straps between blocks
« Reply #157 on: June 05, 2014, 01:29:34 PM »

Most "big box" makers join block sets with a metal strap to stabilise interactions between the different voice sets. Usually it is a metal bar. Some are experimenting with bent ones, which will act as stiff springs

 http://forum.melodeon.net/index.php/topic,14788.msg183317.html#msg183317
Logged
  _       _    _      _ 

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11153
  • Wirral UK
    • Chris Ryall
21st Century Box - cross row helper button C#D instead of ED?
« Reply #158 on: June 05, 2014, 01:45:08 PM »

This innovation happened accidentally when I converted a C#DG to act as a chromatic box, drawing its "accidentals" from the C# row. You start with a pull C#C mid box, but already have pull C on the G row. It was filed to D, making the button C#D.

Now the usual "helper" is an ED, either as a Dutch inversion on main row, or on a helper row. For pull scales, this is the same.

What I hadn't expected was the fantastic utility of that C# push when playing in D, and its E dorian, A mixo etc modes. You end up with play through scales of all but E, but as E is a note of rest in Em, and a weak note in Dmaj or A7 chords that doesn't seem to matter in practice. One of the best mods I ever did. I've in effect lost a push E, gained a push C# (maj7th of D scale, maj3rd of A and a key part of the A7 tritone).

Halftone box players may wryly smile and say … we've always had this :|glug

Logged
  _       _    _      _ 

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11153
  • Wirral UK
    • Chris Ryall
Re: The 21st Century Box
« Reply #159 on: June 19, 2014, 06:09:19 PM »

From the british maker's thread

The 3D printing idea could be the best I've heard. Cost and reproducibility is there. You can create complex internal designs without carving or opening a thing. How to apply it would be the real innovation. I saw a Kickstarter for 3D printed highland pipes that looked pretty fantastic, and they were able to expand the range of the pipes using the design. But how to expand to a melodeon?  Finger boards and buttons, sure. But where else?  Arched/curved internal walls to change volume?  Hybrid with wood to decrease weight?  A waterproof melodeon for playing in the rain?  If you can find a way to 3-D print the reeds....but thinking "outside of the box" (pun intended) is what's necessary to bring these things up to 21st century standards.
First suggested over here. There's nothing new under the sun!

3D printed stuff isn't as strong as it might be, but it might be OK for a melodeon, and it's a very new technology that will become more useful as it gets faster and cheaper and better materials, so yes, at some point...

That thread also introduces the idea of milling a reed block/pallet board combination from solid Al.
Leaping smartly from the 'French' thread, why has new material for bellows not been taken up here? I just don't believe that the design of the melodeon can be improved much, the leap forward has to be in the materials used, and cardboard and tape for bellows really could do with a rethink; I find it hard to believe that there isn't a better material available for the job..

[if you follow through … no need to quote ALL of this, chaps. Be selective please ;) C]
Logged
  _       _    _      _ 
Pages: 1 ... 3 4 5 6 7 [8] 9 10 11 12 13 14   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal