Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Just a little bit of squeak on the basses and chords  (Read 1604 times)

0 Members and 1 Guest are viewing this topic.

Steve C.

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2075
  • Erica, Morse Anglo
Just a little bit of squeak on the basses and chords
« on: January 04, 2012, 01:18:25 AM »

My new Lilly has developed a very slight squeaking on the bass side.

Not exactly a squeak, more like a soft, squeaky chirp?

It happens when pushing any of the bass side buttons (of course you can only hear it when not actually playing).

When you push down on them, you get the squeak going down and if you press the button at the bottom of the travel you can get a bit of the squeak there also.

It "appears" to be the rubbing of the plastic on felt, both the bushing on the hole and the felt pad under the button.

The felts look fine, uniform, not too tight or loose, I do not think.

Did not happen when first played, a few months ago.  Could it be dust or humidity?  BTW, keep the room between 30-55%RH, but it does vary.

Any remedy?  I was just about to get out some silicon or graphite spray, but thought I should ask first.

I took off the bass side plate and no noise from the action inside.

Appreciate your help, as always,  Steve
Logged
Located in Central North Carolina, USA; credit for picture: livingplanet.ca

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Just a little bit of squeak on the basses and chords
« Reply #1 on: January 10, 2012, 08:33:20 AM »

Yes it is a problem that is fairly common,   but can me masked by loud playing, so not always noticed by the player.

First thing to check is - do the felt bushes extend through the full length of the hole?  If not the noise may come from plastic rubbing on wood, and the best thing here is to bush the holes fully.

I would steer clear of any sort of spray that includes a liquid carrier, unless you are completely sure that the liquid contains nothing that leaves an oily or waxy residue.   I find powdered graphite is effective and safe, talc is also good, but not quite such an effective lubricant.  If you don't have powdered graphite to hand then a soft pencil rubbed on to the surfaces is often effective.

It can be very difficult to hear exactly where a squeak is coming from - other possible sources are:
- the joint where the button rod meets the lever
- the joint where the lever is mounted to the woodwork
- anywhere that the spring is in contact with its surroundings
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve C.

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2075
  • Erica, Morse Anglo
Re: Just a little bit of squeak on the basses and chords
« Reply #2 on: January 10, 2012, 12:43:04 PM »

Thanks, Theo--

I will dig a little further before doing anything.

I think you are right about the bushings, tho.  On the inside, they are a little skimpy, like they were cut a mm. too short.

--S.
Logged
Located in Central North Carolina, USA; credit for picture: livingplanet.ca

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Just a little bit of squeak on the basses and chords
« Reply #3 on: January 10, 2012, 01:01:16 PM »

A mm too short should be ok.   I was thinking of a Saltarelle I worked on recently where the bushings were just a narrow ring on the outer edge of the hole.

One other thing to check is that the pistons are parallel to the holes. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal