Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Stall under Pressure  (Read 6374 times)

0 Members and 1 Guest are viewing this topic.

WestOz

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 197
Stall under Pressure
« on: January 17, 2012, 09:09:45 AM »

My D/G Hohner Pressed Wood is fine when practising at home (not too loud), but when used outside for Morris (as loud as possible) a couple of the basses don't fire up as soon as I hit the buttons, but do if I leave buttons depressed. It is especially noticable on faster tunes, as I my fingers only stay on buttons momentarily, and the reed might not sound at all. How to adjust the reeds?
Logged
Castagnari Dony, DB Binci, Hohner Pressedwood,  Liliput, Preciosa,Octoput,etc.

mory

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 752
Re: Stall under Pressure
« Reply #1 on: January 17, 2012, 10:12:05 AM »

Could be possible your playing to hard ? air preasure can be to great causing a sort of pause, you may also have disturbed the set of the reeds or valves need replacing but from your description I suspect it's the first suggestion. Take a peek inside if the valves are curled back from the bass reeds it would suggest they are at fault All the Best mory get back to us
Logged

Martyn

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 455
  • Hohnerohner
    • Martyn White Melodeon Tuning and Repairs
Re: Stall under Pressure
« Reply #2 on: January 17, 2012, 10:33:43 AM »

My D/G Hohner Pressed Wood is fine when practising at home (not too loud), but when used outside for Morris (as loud as possible) a couple of the basses don't fire up as soon as I hit the buttons, but do if I leave buttons depressed. It is especially noticable on faster tunes, as I my fingers only stay on buttons momentarily, and the reed might not sound at all. How to adjust the reeds?

It sounds very much to me like the reed tongues are set too low in the frames, causing them to choke under pressure.

The remedy is to set the reed tongues higher. An easy job on the outside reeds (the push reeds), just lift them up a bit to increase the gap between the tongue and the frame but a bit more tricky on the inner (pull reeds). You can try to ease them down with a small screwdriver or something similar but to be more accurate you will need to remove them from the blocks to adjust them.

Martyn
« Last Edit: January 17, 2012, 10:37:27 AM by Martyn »
Logged
'Anything from a small repair to a full restoration'.
www.melodeonrepairs.co.uk

george garside

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5401
Re: Stall under Pressure
« Reply #3 on: January 17, 2012, 11:01:30 AM »

playing as loud as possible never does anything for a tune anyway and is not necesary even for morris - if it was they wouln't be able to dance to a single whistle which  has been known!

george ;)
Logged
author of DG tutor book "DG Melodeon a Crash Course for Beginners".

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: Stall under Pressure
« Reply #4 on: January 17, 2012, 01:24:28 PM »

playing as loud as possible never does anything for a tune anyway and is not necesary even for morris - if it was they wouln't be able to dance to a single whistle which  has been known!

If you mean the traditional three hole pipe, that's far from a quiet instrument, played entirely on the overblow, and accompanied by a drum to make sure nobody misses a beat. And didn't some of the morris men that spoke to Cecil Sharp complain that they couldn't hear the fiddle that replaced the old whittle'n'dub?

Also, purchase of my Oakwood was triggered by a complaint that Smiffs couldn't hear my Pokerwork over the traffic when dancing in Richmond-on-Thames...
Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Stall under Pressure
« Reply #5 on: January 17, 2012, 02:05:58 PM »

As Martyn says, its is the reed set, but with bass reeds it is always difficult to get them to start properly.   You also need to bear in mind:

The high bass reed also needs to be gapped correctly, because there is some coupling between the reeds, and the low bass reed will start better if the high bass reed is also adjusted optimally.
Some Hohner bass reeds just don't start as well as others.
Bass reeds that are set up to respond best when playing very loud will not respond so well when played gently.

So it really is not always just a simple matter of adjusting one reed.  Good Luck!
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Stall under Pressure
« Reply #6 on: January 17, 2012, 03:22:14 PM »

I can assure you that a NW morris side greatly appreciates the loudest music you can offer - all them clogs drown out any wusses!  Strangely my Pokerwork doesn't seem to suffer from choking, but the DB BPII does.  It helps if you can tap a few extra treble buttons along with the bass as it takes some of the pressure off whilst contributing more volume.

Rob.

Logged

mory

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 752
Re: Stall under Pressure
« Reply #7 on: January 17, 2012, 03:37:04 PM »

Does it happen in both directions WestOz
Logged

WestOz

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 197
Re: Stall under Pressure
« Reply #8 on: January 19, 2012, 04:48:13 AM »

Thanks to all for your input/advice. It does seem to happen on push and pull. I will try opening up the gaps, bearing in mind Theo's remark about relationship with other reeds. i will report any progress (or failure!).
Logged
Castagnari Dony, DB Binci, Hohner Pressedwood,  Liliput, Preciosa,Octoput,etc.

mory

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 752
Re: Stall under Pressure
« Reply #9 on: January 19, 2012, 08:18:14 AM »

 Hi WestOz, it might just pay, if you have the opportunity, to make a comparison with someone else's box both by playing and as a visual reference before you get stuck in AtB mory
Logged

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Stall under Pressure
« Reply #10 on: January 20, 2012, 11:26:20 PM »

This if very helpful for me too. The pull C and pull D fundamentals on my Erica choke when I'm playing at morris practice. I'll try resetting the gap tomorrow.
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Martyn

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 455
  • Hohnerohner
    • Martyn White Melodeon Tuning and Repairs
Re: Stall under Pressure
« Reply #11 on: January 21, 2012, 01:11:49 AM »

It's a good idea when setting the reed higher to hold the bottom third of the reed tongue down with your thumb while lifting the top two thirds. This will avoid any strain on the rivet and also ensure the 'bend' is put in the right place.

Martyn
 
Logged
'Anything from a small repair to a full restoration'.
www.melodeonrepairs.co.uk

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Stall under Pressure
« Reply #12 on: January 22, 2012, 03:25:03 AM »

Excellent advice! Keeping the root of the reed from bending up will help with preventing the whole reed tongue from bending up and creating a problem with the sound of air passing past the reed without the reed  sounding. I've noticed that with some of the reeds I've tuned that getting the reed to sound properly sometimes requires bending the root of the reed down a bit (into the chamber) then bending the tip back up to get the proper amount of gap. Helps the reed to speak quickly.
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

David J

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 186
Re: Stall under Pressure
« Reply #13 on: January 25, 2012, 01:48:43 PM »

Strangely my Pokerwork doesn't seem to suffer from choking, but the DB BPII does. 

Rob.

I had this problem with my BPII as well, but have not experienced it with the Binci where the basses seem more blanced against the treble.
Logged
Luukinen Elene III, Baffetti Binci, and an increasing number of Hohners

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Stall under Pressure
« Reply #14 on: January 26, 2012, 01:10:16 AM »

I've done the gap setting on all the low fundamentals on my Erica. There's been a marked improvement in most of the reeds response under normal playing conditions though not on the low C fundamental, especially the pull C.

I've tried opening up the gap more and more on the low C fundamental. The push reed seems to work fairly well at this point but the pull reed (the one outside the chamber) keeps choking no matter how big a gap I put into the tip. I'm only able to get sound out of the reed at very low pressure but not at standard Morris dance volume. Can anyone help with this? Is this just a standard problem with a Hohner Erica or Pokerwork?

I ended up replacing the original low C fundamental with a brand new reed thinking that I'd created a problem by reworking an old reed from a set of GC Hohner reeds. Can't remember what the original pitches were for the reed I used but I did add a blob of solder to lower the pitch. The brand new reed doesn't seem to behave much better than the old one with the solder though. The new reed still takes a second or two to come up to pitch and stabilize at that pitch. Not sure what to do about that.
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Stall under Pressure
« Reply #15 on: January 26, 2012, 01:21:08 AM »

I've tried opening up the gap more and more on the low C fundamental. The push reed seems to work fairly well at this point but the pull reed (the one outside the chamber) keeps choking no matter how big a gap I put into the tip.
Umm.. The pull reed is the one inside the reed chamber....
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Stall under Pressure
« Reply #16 on: January 26, 2012, 06:01:43 PM »

You're right. I keep getting pull and push mixed up when I'm looking at the reed blocks outside of the instrument.

I'm still wondering if the low C fundamental is more prone to choking for the pull stroke?
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Stall under Pressure
« Reply #17 on: February 08, 2012, 08:08:07 AM »

The more solder a reed has , the slower it will be.
 If you can find a Italian bass reed out of a old piano accordion, you will have to add solder to one reed to bring it to pitch (of course). This may help if the hohner reeds don't cut it.
 The hohner bass reeds are pretty big so you may have to fill in the block for a smaller reed.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

Cag

  • Member
  • *
  • Offline Offline
  • Posts: 44
Re: Stall under Pressure
« Reply #18 on: March 06, 2012, 12:40:28 PM »

My expertise is more in concertinas and if this was a concertina I would say; while a low set will mean a reed will choke more easily, raising the set will not always help if the reed is too thin, and I suspect this is compounded if the clearances are not good. It will also not help if the shape of the set is such that the reed passes through the tightest part of the slot in a progressive fashion rather than all at the same moment.

Chris
Logged

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Stall under Pressure
« Reply #19 on: March 06, 2012, 09:54:49 PM »

My expertise is more in concertinas and if this was a concertina I would say; while a low set will mean a reed will choke more easily, raising the set will not always help if the reed is too thin, and I suspect this is compounded if the clearances are not good. It will also not help if the shape of the set is such that the reed passes through the tightest part of the slot in a progressive fashion rather than all at the same moment.

Chris


I've been wondering how the shape of the tongue itself affects how the reed works. What you're saying is that a reed tongue that forms a straight line from root to tip will be less prone to choking and speak more quickly?
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal