Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Leathers, replacing  (Read 1747 times)

0 Members and 1 Guest are viewing this topic.

OldJack

  • Good talker
  • **
  • Offline Offline
  • Posts: 76
    • Suisun Sailor
Leathers, replacing
« on: February 04, 2012, 06:38:08 PM »

I got a used Hohner Ariette (Chinese mfg.) one row in C to find out if the melodeon will work for me. I play a Wheatstone Anglo CG 30 button and wanted to add a base line, but was unsuccessful. Now, I find I like the melodeon. The old box seems good in every way (I looked inside and checked the bellows) but needs a few new leathers. Need three on the C bass and about four in the treble. The leathers there now are sort of a three layer plastic -- not salvageable. So, I need two things: first, a source for leathers (or valves) and second, instructions on replacing the old leathers. Since I'm retired with limited resources buying a new or better melodeon isn't in the near future. All comments (even negative) and suggestions will be helpful.

Thanks in advance.
Logged

mory

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 752
Re: Leathers, replacing
« Reply #1 on: February 04, 2012, 07:22:45 PM »

Here   http://www.cgmmusical.co.uk/CGM_Musical_Services/Welcome.html   All the Best mory
he will give you all the advice you need

Sorry Jack forgetting my manners WELCOME there is quite a bit of opinion on different glues etc but Charlie Marshal can supply the valves and a glue to go with them The real difficulty is the internal valves and the fact any alterations can mean a bit of retuning is required can I ask where abouts you are send me a message if you want to keep that private (go to members and "send this member a message" )

Just looked at your local Jack the only ones I know in the States are these http://www.buttonbox.com/   and   http://www.irishdancemaster.com/accordion.html    may be someone in the States will come on and offer advice All the Best

CGM will post to USA
« Last Edit: February 04, 2012, 07:43:16 PM by mory »
Logged

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Leathers, replacing
« Reply #2 on: February 04, 2012, 08:34:35 PM »

Hi Jack and welcome,

The valves are inexpensive and not difficult to replace if you are at all OK with your hands. First question, what makes you think they need replacing? Could you post a photo? Or are they just missing?

Secondly, there will be another  set on the other side of the plates - I'm not familiar with the box to know whether you can easily see them, but if you've problems on one side then you may have with the others.

You can probably replace the ones you can see without too much dismantling. The whole job is usually a DIY proposition, albeit perhaps fiddly.

The view is held that if you replace a valve you should consider re-tuning the reed. Personally, since the replacement valves will be pretty similar to the originals, I doubt it will make much difference and your hearing/pitch would have to be pretty good to spot the difference, especially if the box wasn't tuned spot on to begin with.

A clear DIY impact adhesive will be suitable, avoid anything you can't readily get off again like epoxy or superglue.

(Have you done any work on your Anglo? The Anglo would most likely be much easier to work on, but if you're OK doing anything on that then the melodeon shouldn't worry you.)
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

OldJack

  • Good talker
  • **
  • Offline Offline
  • Posts: 76
    • Suisun Sailor
Re: Leathers, replacing
« Reply #3 on: February 05, 2012, 04:49:24 PM »

Thanks for your timely and helpful replies. I am going to open the box again today. When last I looked the reed blocks and stop mechanism seemed reasonably easy to access; so, I'll make measurements and notes for what needs to be done. Except for the visible leathers that need replacing, all else visible, wax and reeds, were free of damage or rust. The treble stop nearest my chin is stiff and half the voices are gone. I suspect a leather has become dislodged and jammed in the stop slide.

I suspect someone has been in there before because the first treble reed sounds a A on the pull and not a G. But that works well for me because some of the Sea Shanties I like need that low A. The other thing I noticed that seems nonstandard is that the stops are open when the knobs are pushed in. All the pictures I've seen suggest that the stops should be open when the knobs are pulled all the way out. Is that right? Or did the Chinese find a different logic in their construction?

Jack (not feeling so old today, went sailing with the wife yesterday. Wonderful!)
Logged

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Leathers, replacing
« Reply #4 on: February 05, 2012, 05:07:30 PM »

There is no "should" with the stops.  Preference of the builder or buyer I suppose.  I've made it both ways, no difference in construction other than placement of holes in the slides.  Some people just like the lower profile of down to play.

That #1 pull being an A is also a preference thing, you can buy the reeds either way.

OldJack

  • Good talker
  • **
  • Offline Offline
  • Posts: 76
    • Suisun Sailor
Re: Leathers, replacing
« Reply #5 on: February 05, 2012, 10:32:57 PM »

Thanks, Bryan. Nice to know there is flexibility. I opened the box and took pictures as I went. There were no leathers or other stuff jammed in the slide and after I put it back together it worked just fine. I really need only two leathers for the bass C, at least it looks that way. Hohner in Virginia will be open tomorrow and it may be I can get those leathers from the source.

I did notice something that is not readily apparent just looking at the box. The inner workings do not reflect pride of workmanship. Looking at how rough some of the parts are I wonder that it works at all. Well, one day maybe I'll have a box as nice as my concertina.

Thanks again to all who responded.

Jack
Logged

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Leathers, replacing
« Reply #6 on: February 05, 2012, 11:04:54 PM »

The Chinese do seem to prefer stops down for open.  It makes a lot more sense, as to play a Hohner 114 with all the voices sounding (like you always should) requires all sorts of junk jammed under/around the stops or gravity deprives you one-by one of the voices.  I only play mine on less than four voices in the car.

You could always fettle the inner workings,a lot can be done with fine sandpaper - just ask all those who have been on the box making course!  It would be interesting to note whether it actually had any audible effect on the sound produced.  Some also recommend that the surfaces should be varnished to minimise sound absorbtion, too.  Trouble is you don't want to mess up your new box, do you (and believe me a load of dust can make it unplayable)?  Perhaps we need to find another guineapig.

Rob.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal