Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: .  (Read 4055 times)

0 Members and 1 Guest are viewing this topic.

aradru

  • Member
  • *
  • Offline Offline
  • Posts: 42
.
« on: March 22, 2012, 01:47:58 AM »

.
« Last Edit: October 13, 2015, 01:28:20 AM by . »
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: SEPARATING REEDS
« Reply #1 on: March 22, 2012, 08:02:46 AM »

Cant you just take the C# plate from one box and the D plate from the other?    It would be quite unusual to have the reeds for two rows on one long plate.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mory

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 752
Re: SEPARATING REEDS
« Reply #2 on: March 22, 2012, 09:15:18 AM »

Can't you just sell the two box's and find one in the key you want? What your asking seems a long way round with likely poor results and it's non reversable AtB mory
« Last Edit: March 22, 2012, 11:23:12 AM by mory »
Logged

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: SEPARATING REEDS
« Reply #3 on: March 22, 2012, 10:19:15 AM »

I was assuming aradru meant that the long strip of reeds (single plate) for the D row does not align with the air holes, so would need to be split and mounted as separate reeds.  Thinking of how long-plate bandoneon reeds are, I would be worried whether there is enough space between the reeds to split them off, but only aradru knows for sure.

The mix of brass and steel reeds is likely to sound a little wierd, though.  If the boxes are not worth preserving (is that heresy?) it would make an interesting project during which you would learn a lot about fettling and tuning.  But to be honest, the outcome is likely to be disappointing.

Rob.
Logged

Quebecois

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1206
  • Accordez-vous donc, c'est si beau, l'accordéon!
Re: SEPARATING REEDS
« Reply #4 on: March 22, 2012, 02:37:49 PM »

I understand there might be some economic issues here, but if the resulting instrument is worth it,  it's probably easier and better to get a set of D reeds... used or new! I guess Theo could help with this, or other sources like CGM.
Logged
Hohner Morgane D/G, pre-Erica Hohner in C/F and G/C,
Hohner Erica A/D, Roland FR-18

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: SEPARATING REEDS
« Reply #5 on: March 23, 2012, 10:59:03 AM »

I think you may run into a problem with this approach in getting an airtight seal between the cut sections.  Usually on boxes with long multi reed plates the reed blocks are built with very thin dividers between the chambers, often not much more than a mm wide.   Blocks designed for separate plates usually have wider reed chamber walls so that there is space for a gap between the reedplates where wax can be placed to hold the reeds and form an airtight seal, or where fixing screws can be  fitted.  Some small format boxes get away with thin chamber walls, and these require very careful wax work to get the reeds mounted.  Gluing in extra slips of wood to thicken the chamber walls might help, and careful filing of the cut edges will help too.

If forced to get a C#/D out of what you have I would just tune the D/D# box down a semitone by weighting the reed tips with solder.  That would be much much much less work, and is reversible.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: SEPARATING REEDS
« Reply #6 on: March 23, 2012, 11:16:27 AM »

Don't take anything said by me as true - I just don't know!  I appreciate your concern as to whether the reeds will perform correctly with the dimensions and mass of the plates reduced by sawing them apart.  There seems to be a general correlation between the quality of reeds produced and the mass of the plate, but I guess that is probably a marginal influence on the overall performance.  As you are looking to end up with a quiet box, you won't be pushing the reeds to extremes, so you've probably already decided it's worth trying.  Just on the practical front, I would be inclined if possible to use a fine disc cutter on the bench with guides to cut off accurately and with a minimal kerf.

Good luck,
Rob.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: SEPARATING REEDS
« Reply #7 on: March 23, 2012, 02:18:13 PM »

I would be doubtful about tuning the brass reeds up a semitone.

Yes if you cut up the reed plates you will need to be fairly accurate.  I don't think a junior hacksaw is the tool for the job.   A full size hacksaw would be much better - more accurate, and probably faster.

Whatever you do you are in for quite a lot of work. ;D ;D
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

pgroff

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1827
Re: SEPARATING REEDS
« Reply #8 on: March 23, 2012, 03:10:05 PM »


   I have other C#D boxes but I wanted one that is ultra light and quiet.

   My young son is playing concertina and the paolo soprani (which is my main box)
   tends to stomp all over the sound of the concertina.


Hi aradru,

I see what you mean -- I also like having a quiet mellow instrument to play along with students -- I have a brass reeded Jones anglo I use for that, for example. 

Or I use a Salterelle accordion with stops that take it down to one reed, which brings me to an idea you could try:

If your Paolo has no switches, or just 2 switches, so you can't get down to one reed, you can still block off some ranks of reeds using a long thin strip of paper laid just under the base of one or more reedblocks.  The strip should be either the width of the reedblock, or half the width of the reedblock, depending on how your accordion is laid out and what you want to accomplish.

I have a 4 voice Paolo with 2 couplers, unusually tuned LMMH.  The couplers switch from LMMH to MM.  So sometimes I put in paper strips under the L reeds for both rows, then the coupler switches from MM to MMH.  If your box is LMMM, you could use paper strips to block off 2 sets of M reeds for each button row, then your couplers would switch from LM to M.

It's pretty quick and totally reversible to do if you take care when opening up the box, taking out the reedblocks, and putting everything back (mind those leathers and helper springs don't get fouled).

PG

Logged

pgroff

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1827
Re: SEPARATING REEDS
« Reply #9 on: March 23, 2012, 07:52:02 PM »

Hi aradru,

Sure, it's clear.  And if you would be going back and forth often between reeds blocked and unblocked it might make sense to have a separate quieter instrument.

Good luck with the project!

PG

Logged

mory

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 752
Re: SEPARATING REEDS
« Reply #10 on: March 24, 2012, 08:55:26 AM »

aradru good luck with it, with a bit of carefully thought out planning and some patience (and your recent success) you'll get there I'm sure, certainly a learning curve opportunity. All the Best mory
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: SEPARATING REEDS
« Reply #11 on: March 24, 2012, 09:49:04 AM »

Another thought about how you could accomplish this:  it might be easier to make a new reed block?   If the difference in spacing is not too great it may be possible to match the holes in the board with slightly wider spaced reed chambers.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal