Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: internal microphone  (Read 8661 times)

0 Members and 1 Guest are viewing this topic.

gioui

  • Guest
internal microphone
« on: April 11, 2012, 09:47:38 AM »

what is the best internal microphone for  low ? ( left hand )
Logged

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: internal microphone
« Reply #1 on: April 11, 2012, 11:19:30 AM »

Microvox M400 is pretty good for this.

I use a Microvox swan neck mounted inside the bass end, with the mic element right next to one of the sound holes to make the sound less "boxy". It's connected to a phono socket at the back of the bass end.
Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk

gioui

  • Guest
Re: internal microphone
« Reply #2 on: April 11, 2012, 12:42:05 PM »

i use 2 microphone capsule sennheiser ke4-211 the sound is nice but is too sensitive ..... the notes where the microphone is pointed  play very strong others feel much less
Logged

Quebecois

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1206
  • Accordez-vous donc, c'est si beau, l'accordéon!
Re: internal microphone
« Reply #3 on: April 11, 2012, 02:08:23 PM »

I have tried a few things with microphones, it's a tricky issue as noted in the previous post. In my father's old Corso the previous owner has installed 2 of those "coin" devices inside the treble side and they seem to be piezo transducers rather than microphones.

I experimented using a surface transducer (designed for mandolins or violins) stuck to different places inside and outside the treble side of my Morgane and some interesting sound is coming out. Also a small condenser mike, but then all the noise from the pallets is also amplified!

I ended up using an external condenser microphone designed for instruments.

Also check http://diato.org/sonoacc.htm for some infos on using microphones.
Logged
Hohner Morgane D/G, pre-Erica Hohner in C/F and G/C,
Hohner Erica A/D, Roland FR-18

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: internal microphone
« Reply #4 on: April 11, 2012, 05:52:40 PM »

I have tried a few things with microphones, it's a tricky issue as noted in the previous post. In my father's old Corso the previous owner has installed 2 of those "coin" devices inside the treble side and they seem to be piezo transducers rather than microphones.

I experimented using a surface transducer (designed for mandolins or violins) stuck to different places inside and outside the treble side of my Morgane and some interesting sound is coming out. Also a small condenser mike, but then all the noise from the pallets is also amplified!

I ended up using an external condenser microphone designed for instruments.

Also check http://diato.org/sonoacc.htm for some infos on using microphones.


Similar comments from me, internal mics can often have an unnaturaly boxy sound due to cavity resonances under the bass end cover and are prone to picking up action noise and air valve hiss.

I use a Beyerdynamic Opus 82 Set (with in-built preamp but needs phantom power) clipped to the bass end strap which is robust and has excellent bass response, I recommend using a foam windshield to remove rumble from wind (if playing outdoors) or air valve airflow.
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

Quebecois

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1206
  • Accordez-vous donc, c'est si beau, l'accordéon!
Re: internal microphone
« Reply #5 on: April 11, 2012, 07:04:41 PM »

Windshield is a good idea!
The other issue when using external microphones with melodeons on stage is often the feedback from the stage monitors. I solved this problem by using my own amp, placed behind me, with the pre-amp output fed to the P/A in a channel that sends no signal to the monitors. This way I have my own monitor, and I can have some control on the sound volume.
Logged
Hohner Morgane D/G, pre-Erica Hohner in C/F and G/C,
Hohner Erica A/D, Roland FR-18

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: internal microphone
« Reply #6 on: April 11, 2012, 11:02:01 PM »

Windshield is a good idea!
The other issue when using external microphones with melodeons on stage is often the feedback from the stage monitors. I solved this problem by using my own amp, placed behind me, with the pre-amp output fed to the P/A in a channel that sends no signal to the monitors. This way I have my own monitor, and I can have some control on the sound volume.

The Beyer is quite directional, I can have more volume in the monitors than anyone else on stage can stand without any feedback problems :-)

(so long as the mic points at the bass end and not at the monitor, obviously)
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

Andrew Wigglesworth

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1101
  • 07
    • My website
Re: internal microphone
« Reply #7 on: April 13, 2012, 12:47:06 AM »

Windshield is a good idea!
The other issue when using external microphones with melodeons on stage is often the feedback from the stage monitors. I solved this problem by using my own amp, placed behind me, with the pre-amp output fed to the P/A in a channel that sends no signal to the monitors. This way I have my own monitor, and I can have some control on the sound volume.

The Beyer is quite directional, I can have more volume in the monitors than anyone else on stage can stand without any feedback problems :-)

(so long as the mic points at the bass end and not at the monitor, obviously)

I use a Beyerdynamic clipon for the bass end too (after seeing your comments on it a while back Ian) and can confirm that I've never had feedback problems on stage. Made people jump a couple of times when I've dropped it though.

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: internal microphone
« Reply #8 on: April 13, 2012, 02:49:37 PM »

Windshield is a good idea!
The other issue when using external microphones with melodeons on stage is often the feedback from the stage monitors. I solved this problem by using my own amp, placed behind me, with the pre-amp output fed to the P/A in a channel that sends no signal to the monitors. This way I have my own monitor, and I can have some control on the sound volume.

The Beyer is quite directional, I can have more volume in the monitors than anyone else on stage can stand without any feedback problems :-)

(so long as the mic points at the bass end and not at the monitor, obviously)

I use a Beyerdynamic clipon for the bass end too (after seeing your comments on it a while back Ian) and can confirm that I've never had feedback problems on stage. Made people jump a couple of times when I've dropped it though.

The Opus 82 was particularly good for the bass end with a very flat extended response, but as you say it don't half make people jump if you drop it when your PA goes down to 30Hz...

Unfortunately Beyer don't seem to make this any more, and all their newer wind instrument mics seem to have considerable bass rolloff :-(
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

gioui

  • Guest
Re: internal microphone
« Reply #9 on: April 13, 2012, 02:50:09 PM »

i use this http://www.master-production.com/acc_micro.htm (kit australia) but in the right hand i Use an external microphone (shure sm 57) the internal capsule sound like in a closed box but is a system very practical for live application
Logged

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: internal microphone
« Reply #10 on: April 13, 2012, 04:24:01 PM »

Incidentally, there's a parallel discussion about melodeon amplification going on over at Mudcat, where Ted Crum from Steamchicken recommends the T.bone CC75 (Thomann) - remarkable value for money for just £31.32 at today's Euro conversion rate. It's a clip on gooseneck mic with no battery box needed, but needs phantom power.
« Last Edit: April 13, 2012, 04:39:17 PM by Anahata »
Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk

Mike Hirst

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1433
  • Black Dot B/C, Bastardo C#/D, Corona II GCF
Re: internal microphone
« Reply #11 on: April 13, 2012, 04:35:18 PM »

When last in Catelfidardo we visited MusicTech

http://www.musictech-midi.com/GB/

Although best known for their midi controllers (available for PA and diatonics), they also make very good internal mics. My friend bought an amplification system for his gabbanelli three row. On purchasing the system he was taken into the workshop where he was shown how to fit the electronics. No one in the shop spoke English and our Italian, although good enough to discuss acordeons, certainly did not extended to naming electrical components. On returning to the UK he managed to fit the pickup (with only a couple of screws left over). The sound was impressive and IMO opinion it was one of the best solutions I have seen.

I have always preferred using an external mic. I did once purchase a Hohner mic from a music shop in Leeds, sometime c.1980. The mic was slung on blue rubber which was screwed to a treble reed block. I opened my Hohner one row, attached the mic sling, drilled a hole for the wires, pushed the wires through and plugged the hole. The first gig I did was at the Tower Ballroom in Hull, with the accordion D.I.ed we did a soundcheck. This could not have been a more spectacular failure. The internal pickup was constructed using a diaphragm mic. As I played the air pressure in the bellows distorted the diaphragm cause the mic to cut out. About as much use as a chocolate fireguard.  >:(
« Last Edit: April 13, 2012, 04:39:43 PM by Mike Hirst »
Logged
Semper idem, sed non eodem modo

gioui

  • Guest
Re: internal microphone
« Reply #12 on: April 13, 2012, 07:29:40 PM »

KIT MUSICTECH is IDENTICAL TO WHAT I HAVE, HAS 3 CAPSULES Sennheiser KE ... AND THE SAME INSTALLED ON ALL Castagnari, OR MAKE ANOTHER KIT MORE ECONOMIC
Logged

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: internal microphone
« Reply #13 on: April 14, 2012, 10:40:06 AM »

I'd consider an external mic. The microvox things work very well and are relatively cheap - mine has gone through around 70 gigs without once giving any trouble. But they are boxy and inelegant. The problem with internal mics is that they tend to be very individual, what works for one box in one position won't work for another.
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: internal microphone
« Reply #14 on: April 14, 2012, 10:53:05 AM »

The problem with internal mics is that they tend to be very individual

For a long time the mic for my Pokerwork was the capsule pulled out of the mic supplied with a 1960s Grundig tape recorder (by then the tape recorder itself was long defunct), and attached to the treble reed blocks with a couple of double sided foam plastic sticky pads. It worked brilliantly until a tiny internal wire broke irreparably. So I tried a variety of cheap dynamic mic capsules similarly attached, and every one of them sounded absolutely ghastly, and I switched to external mics including Microvox.

Internal mics are a black art.

If you want a hurdy gurdy wired for sound when you're buying it new, the standard practice is to get the HG maker do do it for you as only he will understand how the instrument is put together and what will work.
Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: internal microphone
« Reply #15 on: April 14, 2012, 11:20:32 AM »

Incidentally, there's a parallel discussion about melodeon amplification going on over at Mudcat, where Ted Crum from Steamchicken recommends the T.bone CC75 (Thomann) - remarkable value for money for just £31.32 at today's Euro conversion rate. It's a clip on gooseneck mic with no battery box needed, but needs phantom power.

Does the CC75 "gooseneck" bend and can the capsule be twisted or rotated?

If not, when you clip this to your bass end strap you won't be able to get the mic into the right position and pointing at the bass end as opposed to parallel to it.

The Opus 82 one is longer and more flexible and can be twisted, but it's still not always easy to get it into just the right position.
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: internal microphone
« Reply #16 on: April 14, 2012, 01:59:46 PM »

I believe Andy Cutting uses a boundary layer microphone in the bass end of his boxes.  These used to be available from Radio Shack and like most mics are inordinately expensive for what they are!  An electret capsule is mounted facing the bass board with a gap of around 1-2mm.  This makes it quite non-directional, typical uses commercially are as a table centre mic for conferences.  It also boosts the bass response, so a second advantage for the left hand of a box.  I have not tried one internally, but used one for a time on the left hand of a 4-stop as it is quite compact and room is short on such small boxes.  It worked very nicely, delivering the full growl of the bass.  Unfortunately some clown kicked my box during the break and smashed the mounting!

On the treble end, I have used the Microvox type bars, which have three electret capsules in them.  OK, if a little short of full frequency response.  The same arrangement mounted behind the grille cloth works just as well but you may have to avoid getting too enthusiastic as it is possible to exceed the maximum sound levels and start to distort.  I had a Dino Baffetti "Morris 3" with internal mics like this and the batery mounted inside wired so that plugging the (mono) jackplug into the stereo socket switched the system on.  Three mics glued to the grille cloth and a single one in the bass end wired through the bellows with a serpentine path, glued to each fold.  It was absolutley reliable as nothing had to be distrubed in setting up, but there was a rather flat sound, presumably due to a mix of the limited frequency range of the capsules and the fact that they are working close to their maximum sound level input.

I don't know how people keep gooseneck mics working - perhaps they are just more gentle with them than me?  I had some AKG ones and the performance was really good.  Not recording standard perhaps, but more than adequate for ceilidhs when the room accoustics are going to be so influential.  Unfortunately after a few uses, I spent hours resoldering the wires and trying to repair the bases of the goosenecks which snapped when bending the mics into position (less than delicate handling when changing boxes between dances).  Very nice to be able to switch off the battery between tunes so the dancers hear the band talking about them!

I now use AKG C1000 condenser mics on stands.  Best sound so far, but the switches are difficult to turn off with a thumbnail.  I do sometimes regret not having internal mics as all you need other than the box is a lead and you can plug into a sound system at a moment's notice.

Rob.
Logged

Andrew Wigglesworth

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1101
  • 07
    • My website
Re: internal microphone
« Reply #17 on: April 14, 2012, 02:58:51 PM »

To be honest I don't see how fitting the element from a boundary microphone has much to do with anything other than the inherent qualities of the capsule on its own.

Pressure zone microphones/boundary microphones are used on a flat hard surfaces and and consist of a little condenser microphone placed a small distance above and facing the surface. You would typically use one on a table or a wall. They work by utilising the reflected sound from the hard boundary, hence the term boundary microphone.

I don't know all of the technicalities of them, but I do know that they need to be placed on a clear area of about a metre square to work effectively. I used to use one to record meetings. Fitting one inside the bass end of a melodeon is not the way to use it as a boundary microhone and I would think would be quite an expensive way of aquiring a relatively cheap condenser capsule.

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: internal microphone
« Reply #18 on: April 14, 2012, 11:09:42 PM »

As has been said before, a high quality (hypercardioid?) stand mic is probably the best solution for the treble end. It's not really satisfactory for the bass end because of the varying distance between box and mic as the bellows move, which is why a good quality clip-on can be better.
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: internal microphone
« Reply #19 on: April 15, 2012, 08:31:28 AM »

As has been said before, a high quality (hypercardioid?) stand mic is probably the best solution for the treble end.

I did exactly this with a Beyer M201 for a while, then discovered that the ubiquitous Shure SM57 works just as well. The hypercardioid response of the M201 would help if you have high foldback levels, but without drums or other loud instruments in the band I don't have that problem. Plus the SM57 is a cheap and robust microphone!
Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal