Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2] 3 4   Go Down

Author Topic: Table Saw  (Read 14780 times)

0 Members and 1 Guest are viewing this topic.

oggiesnr

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 995
  • Dino BPII, Alfred Arnold Bandoneon, Loffet G/C
Re: Table Saw
« Reply #20 on: April 21, 2012, 07:11:25 PM »

As far as sizing wood stock, planing, thicknessing etc you may well find it cheaper to find a local joiner/cabinet maker and pay them to do it.  Before I downsized my workshop I had a fairly comprensive list of machinery but when I actually sat down and did the costings all I really gained was the write-off with depreciation and could have put the cash to better use.  You have to machine a lot of wood to make buying machinery cheaper than paying someone who knows what they're doing their hourly rate.

Steve
Logged

Gromit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 588
Re: Table Saw
« Reply #21 on: April 21, 2012, 09:21:02 PM »

Jet was/is good (ish) make and this is perhaps a better spec. than the Poxon

http://www.axminster.co.uk/jet-jet-jts-10-bench-top-saw-bench-prod208698/

Logged

an bosca ceoil

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 347
Re: Table Saw
« Reply #22 on: April 21, 2012, 11:00:52 PM »

And if you buy one with tilt you can make thumb grooves in keyboards (if you take care, otherwise you might not have use for said groove)
Logged

Prestidigitator

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 448
  • Saltarelle, Hohner, Oakwood Baffetti
Re: Table Saw
« Reply #23 on: April 22, 2012, 07:36:21 AM »



Made two already on Emmanuel's courses where he uses a table saw for all sorts of tasks. Next on my list, after the table saw, is a router, then making a box is a possibility  :o

As Graham W says, if you go for a router then do get a table for it as well. I have an old Elu MOF96 which doesn't have a "soft start" but a fair bit of power. Using it freehand, especially on fine work, is a non-starter, and I suspect the same applies to most new ones. All the effort is spent keeping the tool in the workpiece rather than feeding the workpiece to the tool in a controlled way. A table gives feed and, importantly, depth control; and is less terrifying.

I'm glad this discussion cropped up, as my old Burgess bandsaw has said "adios", and I was looking to replace it with a 2-wheel bandsaw. In light of what's been said here, I rather think I'll go for a decent table saw and perhaps get a cheap-ish scrollsaw for fiddly bits.
Logged

Gromit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 588
Re: Table Saw
« Reply #24 on: April 22, 2012, 10:55:29 AM »

Comments on the proxxon here - I find this an interesting woodworking forum

http://www.ukworkshop.co.uk/forums/post619323.html#p619323
Logged

Quebecois

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1206
  • Accordez-vous donc, c'est si beau, l'accordéon!
Re: Table Saw
« Reply #25 on: April 23, 2012, 03:16:13 PM »

Another option is a radial saw. Can also be used as a mitre box!
Logged
Hohner Morgane D/G, pre-Erica Hohner in C/F and G/C,
Hohner Erica A/D, Roland FR-18

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Table Saw
« Reply #26 on: April 23, 2012, 03:17:56 PM »

Comments on the proxxon here - I find this an interesting woodworking forum

http://www.ukworkshop.co.uk/forums/post619323.html#p619323

Well I'm not surprised, cutting 20mm maple on a model making saw with a max depth of cut of 22mm.   Wrong tool for the job!
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Table Saw
« Reply #27 on: April 23, 2012, 04:46:20 PM »

I think table saw is the best option with a good fence (looking at the picture of the proxxcon the fence does not go the full depth of table or maybe there is a slide to the fence - but that would not lock the fence front and back that could be problem.) Adjusting the fence to the table and blade is the most important thing , not always done right at the factory and should be checked also good blade is a must I like planer blades for a cleaner cut well worth the cost if you pass the wood through with smooth motion (don't stop ) you'll get cuts without saw marks. I say any saw with good power, good fence and proper set up will give good results. I would also say when cutting small bits use blade inserts and push sticks.

table saws  main use ripping , cross cutting , dados or rabbets
radial arm  saws cross cuts and dado can be used for ripping but dangerous  not good for small work the motor gets in the way of hands and sight.
band saw   odd shapes and re sawing  not very accurate usually re quires more work to get finished product

Also unless you will be using router as stand alone unit then get a small router/shaper like delta or similar table top type
unit most adjust easier and have vac. hook up and just as cheap as buying two units router and router table.

Good luck
Michael
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Keithypete.

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 917
Re: Table Saw
« Reply #28 on: April 23, 2012, 05:20:36 PM »

Try a tool or machine auction. Second-hand yes, but you want something with a cast iron bed. Above all elaw make sure it is securely fixed, ideally to the floor.
Logged
Beltuna Sara II - B/C flavour.
Borsini - G,D,A.
Pokerwork B/C.
PRIMATONA IV, B/C.

Gromit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 588
Re: Table Saw
« Reply #29 on: April 23, 2012, 07:37:12 PM »

"Well I'm not surprised, cutting 20mm maple on a model making saw with a max depth of cut of 22mm.   Wrong tool for the job!"

It would seem so and yet they are flogging tungsten carbide blades to cut " balsa, plywood, hard and soft woods,...."?

Do you not do any hardwood repairs to boxes Theo ?

The Proxxon appears to be a well made saw but a bit limited in what it can handle - I'd be tempted to go for something with a bit more oomph to it.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Table Saw
« Reply #30 on: April 23, 2012, 07:45:27 PM »

I'd be tempted to go for something with a bit more oomph to it.

What do you use?

Yes it will cut all those materials, but maple is a very hard hardwood, and 20mm is closet to the max thickness.   I just wonder how much 20mm maple was involved, I thing the poster may have been asking too much of a small tool.  There is very little material that thick in a melodeon.  Yes of course I repair hardwood melodeons!  Here is a photo of the most extreme sawing I have done with the Proxxon:
« Last Edit: April 23, 2012, 07:47:09 PM by Theo »
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Gromit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 588
Re: Table Saw
« Reply #31 on: April 23, 2012, 08:07:28 PM »

"Yes of course I repair hardwood melodeons!"

Thought so - wasn't meaning to be rude.

Boxcall - I'm intrigued to know how you use planer blades on a tablesaw or am i misunderstanding something

".....good blade is a must I like planer blades for a cleaner cut"

and

radial arm saw for ripping!! "can be used for ripping but dangerous" you bet.

Can't see why folks here have a downer on bandsaws they are an essential part of a small joinery shop - lot quicker and easier to cut tenons on.
Logged

oggiesnr

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 995
  • Dino BPII, Alfred Arnold Bandoneon, Loffet G/C
Re: Table Saw
« Reply #32 on: April 23, 2012, 08:33:57 PM »


Can't see why folks here have a downer on bandsaws they are an essential part of a small joinery shop - lot quicker and easier to cut tenons on.

For small cuts like tenons they're fine (if well adjusted) although I use a fretsaw  (:)

For bigger stuff I've found that the one I had (an INCA) just wasn't accurate enough and tended to waver on the line even when using a fence.  They don't give as polished a finish on the cut edge as a table saw.

Now as you get bigger (and more expensive) they get better but even so they're low on my list of must have workshop tools.

As far as routers go, I have two, a ELU which I only use with a table and then rarely (and cost more than it's use has justified) and a Dremel Mult-tool with router attachments which is great for fiddly little jobs.

Steve
Logged

Gromit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 588
Re: Table Saw
« Reply #33 on: April 23, 2012, 09:06:12 PM »

Well any machine should be well adjusted otherwise it's not going to perform as it should and it depends on the size of the bandsaw - big bandsaw will cut deep tenons - not used an Inca - thing with a bandsaw is to fit a good blade and ditch the one it's supplied with.

Elu's were great routers (and saws, etc.) then Dewalt took them over.
Logged

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Table Saw
« Reply #34 on: April 23, 2012, 09:32:22 PM »

I can't imagine being without my bandsaw, but would never use it in place of my tablesaw.  A table saw is quick and accurate with a good blade and fence.  A bandsaw can cut extremely well (I can use mine to cut thin veneer), but it takes a lot of careful set up.  And each time you change a blade on band saw you have to go through the set up process again.

I've never used those small Proxxons, and don't doubt they do well with smaller pieces, but I'd sure consider a bigger size table top saw, like a 10" size.  Still reasonably priced and small, but can handle quite a bit bigger stock and good choice of blades available.

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Table Saw
« Reply #35 on: April 23, 2012, 11:02:12 PM »


Boxcall - I'm intrigued to know how you use planer blades on a tablesaw or am i misunderstanding something

".....good blade is a must I like planer blades for a cleaner cut"


Hi Gromit
I don't use a blade from a surface planer.
I talking about a planer blade for table saws they come in different sizes 8" 1o" etc.
the blades unlike most blades have no set to the teeth which gives a smoother cut . most blades have a set to them meaning that one tooth bends slightly to one side of the blade and the next tooth bends to the other side and so on , which will leave saw marks on the wood being cut - planer blades don't or not as much usually only when you stop or shift your hands also use of feather board helps with this. try one and you won't need to run the edge though a joiner.
Michael
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Gromit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 588
Re: Table Saw
« Reply #36 on: April 23, 2012, 11:32:33 PM »

Thanks
I understand - you must be in the States those blades as far as I know are not available in the UK - we've got all sorts of safety regulations regarding saws and blades these days. Nearest I've got is a 40 tooth fine blade on my Festool that leaves a very smooth finish.
Logged

Graham W

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 277
Re: Table Saw
« Reply #37 on: April 24, 2012, 09:14:14 AM »

They have a slightly different attitude to saw benches over the water, as far as I understand;)

These 'planer' type blades are available in the UK for crosscutting, most usually in a mitre / radial saw of some sort, and give an excellent smooth and accurate glue ready finish. They are expensive and easily damaged by misuse. They are described as HiATB or 'Laminate' blades.

I've not seen one quite like that for ripping use, but one Of the industrial suppliers like Atkinson-Walker would be able to advise on what blade was best for your particular need.

A brief warning though  for people who aren't familiar with circular saw blades. It's seriously important to be aware that saw blades for ripping and cross cutting have different tooth geometries, and using the wrong blade for the wrong purpose has the potential to damage the blade, the saw and yourself. A circular saw can grab and hurl or pull large pieces of wood with murderous force.

Logged

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Table Saw
« Reply #38 on: April 24, 2012, 12:06:45 PM »

A circular saw can grab and hurl or pull large pieces of wood with murderous force.


I've blocked a couple of those pieces with  my hip.  I don't really recommend that method. :o

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Table Saw
« Reply #39 on: April 24, 2012, 02:12:08 PM »

Here is the type of blade I'm talking about good for ripping and cross cutting used on my table saw.
I don't use my table saw for cross cuts unless I'm cutting wide panels and only when the piece is short enough to be handled
safely, compound mitre saw is the best for that IMO radial arm could also be used but there tends to be more play in the rail resulting in poor quality cut.

/www.google.com/products/catalog?hl=en&rlz=1G1GGLQ_ENUS326&q=oldham+planer+blades&um=1&ie=UTF-8&tbm=shop&cid=12917992164332760720&sa=X&ei=aqKWT4iEBenx6AGRwOyRDg&ved=0CIwBEPMCMAI#ps-sellers

Michael
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D
Pages: 1 [2] 3 4   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal