Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 2 [3] 4   Go Down

Author Topic: Table Saw  (Read 14771 times)

0 Members and 1 Guest are viewing this topic.

Cag

  • Member
  • *
  • Offline Offline
  • Posts: 44
Re: Table Saw
« Reply #40 on: April 25, 2012, 11:13:15 AM »

A key quality in any machinery is repeatability. Its all very well having carefully plotted dimensions but if you cannot make them happen time and time again your work can become ragged. Repeatability in a saw is tied up in the fence.  Any saw above the lowest price range will have adequate bearings and a strong motor, the fence is where the money needs to go. Also look at the nature of the well around the blade. Blades which cant over often have wide holes filled with inserts of dubious quality. I spent a lot of time making a better insert for my last saw from wood. If you are making a small piece of trim the last thing you want is any roughness in the table.

I went from paying other people to cut wood to cutting my own. At first it made sense letting someone else maintain the equipment, deal with the dust, and do boring saw work breaking down larger pieces of timber.  After a while I realised the only way to get complete control of the process was to be able to look at wood as if it had no finite dimensions, it was whatever size I wanted. To do this I now have a bandsaw and a sander thicknesser. If I was making accordions (I make concertinas) I would buy an accurate table saw with guaranteed repeatability and a router table.
Logged

Graham W

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 277
Re: Table Saw
« Reply #41 on: April 25, 2012, 02:11:34 PM »

Here is a decent smaller table saw for someone. eBay :  160787456467
 Wadkin saws are about as solid and accurate as it gets, I have a later version of this saw and have been highly delighted with it. They can be run from an Inverter or simply fit a single phase motor and starter.  You will end up with a saw that will outlast and outperform light weight new saws that cost far more money. 
Logged

Gromit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 588
Re: Table Saw
« Reply #42 on: April 25, 2012, 07:00:33 PM »

Yes Graham - Wadkin or Startrite table saws, bandsaws, planers, spindle moulders, morticers etc. were pretty much standard machinery in joinery shops I used to work in the past.
Logged

melodeon

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1732
Re: Table Saw
« Reply #43 on: May 02, 2012, 04:27:42 AM »

Consider a used INCA model 259.

Jim Krenov ( self proclaimed wood guru)  teacher and author ( I have the first Swedish workbench custom made for him) said if he had two stationery power tools it would be a band saw and a jointer.

Do  not buy or use a radial arm saw, even as a cutoff saw.

Also it you have the funds consider products by  Festool...

Also there is a very small table saw by HEGNER.. I believe now discontinued, at least for the US.
If you want a mutipurpose multi function saw and can afford it.. decent unit. EXPENSIVE.

« Last Edit: May 05, 2012, 08:27:07 AM by melodeon »
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Table Saw
« Reply #44 on: May 02, 2012, 10:00:29 AM »

I started with a radial arm saw. I thought it would be the answer - wrong! They are not good.

I now have three table saws ranging from very small to very big, plus a bandsaw - all good.  (:)
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

melodeon

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1732
Re: Table Saw
« Reply #45 on: May 05, 2012, 08:34:03 AM »

I have a 3 hp 12" sliding table table saw.. a smaller table saw, 14" band saw, 18" band saw, Delta Scroll saw, 12 " planer, 4" IIDA planer,  22" drum sander,   24" drum sander , floor mounted drill press, bench drill press , horizontal boring machine, 6 " 3 ft jointer, 6" 6ft Jointer....  assorted other stuff...

If I were on a budget I would get a used Delta Rockwell Contractors Saw  and a video by Kelly Mayer ( sp) and set it up.
I would get an older quality 6" jointer perhaps a Delta or a 50's or 60's Craftsman.

Logged

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Table Saw
« Reply #46 on: May 22, 2012, 10:25:54 PM »

Consider a used INCA model 259.

I have this model - the one with the tilting table. It's a very accurate saw but can be difficult to deal with the tilting table for angled cuts. The mortising setup is very nice though making the saw dual purpose.

My first choice for any ripping process is my band saw. The kerf is thinner meaning there's less sawdust on the floor and it's much safer than the table saw for cutting thin pieces. I've used mine for almost all of the pieces in my mini-melodeon one way or the other, the table saw being used for cross cuts. Smoothness of cut on the band saw depends largely on the type of blade and the set up of the saw. Yes, there are setup issues with a band saw, but that's true of any machine tool in the shop - planer, thicknesser, table saw, router, and so forth. With the band saw you can cut veneer - something the table saw can't do.
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

Jon Loomes

  • Performer, Recording Engineer, Luthier.
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 115
  • Non plaudite. Pecuniam jacite.
    • www.jonloomes.com
Re: Table Saw
« Reply #47 on: May 23, 2012, 11:01:15 AM »

Proxxon stuff does seem to be very good.  A scroll saw might also be a useful thing to have.

Telemorris

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 405
  • C/F Preciosa
Re: Table Saw
« Reply #48 on: May 24, 2012, 06:59:56 PM »

I just bought a used scroll saw and have found it extremely useful for cutting air holes in treble and bass palletboards. It turned out to be fairly easy to stack a register and a reedblock shoe on top of the bass pallet board and then cut the holes all together. I hated that job until I figured out that the scroll saw could do them all together.
Logged
Ed Stevens
Bridgetown Morris Men
Portland, Oregon, US
Erica D/G, Presswood Pokerwork G/C, Preciosa C/F

oggiesnr

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 995
  • Dino BPII, Alfred Arnold Bandoneon, Loffet G/C
Re: Table Saw
« Reply #49 on: May 24, 2012, 09:59:58 PM »

Scroll saws are great for stack cutting, fretting ends etc.  They are really bad at straight lines as you cannot use a fence because of the differences between blades, even those in the same packet.  The blades are basically stamped out (OK it's a bit more technical than that) and one side tends to be sharper than the other so often cutting in a straight line means cutting at a slight angle to the blade.

Steve
Logged

Andy in Vermont

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 948
  • Mélodie
    • Melodeon Minutes (blog)
Re: Table Saw
« Reply #50 on: May 27, 2012, 01:29:44 PM »


Jim Krenov ( self proclaimed wood guru)  teacher and author ( I have the first Swedish workbench custom made for him) said if he had two stationery power tools it would be a band saw and a jointer.


Jeff, good advice as always -- except I think that we can give Krenov a bit more credit than "self-proclaimed" implies -- he did earn his cabinetmaking degree at a Swedish trade school, and certainly many others considered him to be a guru!
[Correction: He apparently didn't earn the degree -- but he did get hired to teach at the school ten years later! -A.]

I have occasionally amused myself with the thought of a Krenov-inspired melodeon -- built without drawn plans.  Probably apple with mixed heartwood/sapwood.  A little drawer on one side, for who-knows-what.  Hand-whittled buttons.  And a spindly-legged stand to display it -- or a "tea cabinet" to keep it in!

Nice thread -- have enjoyed reading the responses.
-Andy
« Last Edit: May 28, 2012, 01:11:08 AM by Andy in Vermont »
Logged

melodeon

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1732
Re: Table Saw
« Reply #51 on: May 28, 2012, 05:45:32 AM »

Krenov did not earn his degree at the Malmsten Skol. He left by mutual agreement after one year. Fact.

His "job" at Mendocino was arranged for him by a Stanford professor, who was himself an author of many books including the subjects of Shaker furniture and Windsor chairs.  Krenov never thanked him for the introduction or recommendation or arranging the interview for the position. Fact. Never.

Krenov was a brilliant designer and a good workman. He never made a living doing woodwork. Fact.

A Krenov designed accordeon would be interesting.  He was fond of unsteamed pearwood and of course masur birch and "Swedish Pine".



Logged

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Table Saw
« Reply #52 on: August 27, 2012, 10:51:23 PM »


I have one of those, which my recommendation is based on.   But this one is a newer version, same cutting capacity, but a much better fence and slightly larger table, and cheaper!   http://www.proxxon-direct.com/acatalog/Table_Saw_FET.html 

I am looking at getting something like this soon.

Has anyone actually used the FET? Also, anyone know if it's true that you have to buy Proxxon blades for their saws?

And finally - any other recommendations for a similar saw (UK and not second-hand)?

Ta
Malcolm
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Table Saw
« Reply #53 on: September 02, 2012, 12:08:31 PM »


Has anyone actually used the FET? Also, anyone know if it's true that you have to buy Proxxon blades for their saws?

So would I be the first here to buy a FET? Or is there an Omerta condition on the order form ???
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Table Saw
« Reply #54 on: September 02, 2012, 12:39:46 PM »

Sorry missed this first time round, I have a FET and am happy with it. The only thing is I think the supplied blade is a bit coarse for the stuff I do so I need to get apnea with more teeth.

Prestidigitator

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 448
  • Saltarelle, Hohner, Oakwood Baffetti
Re: Table Saw
« Reply #55 on: September 02, 2012, 12:48:54 PM »

In trying to decide whether to replace my old bandsaw with a table saw, I had a look at one of these.

It is well-built, as one might expect, and very compact, but I was rather put off by the spec. for the blades. The smaller diameter 50mm blades looked hard to find unless buying the Proxxon ones. The larger sizes up to 85mm diameter can be found from other sources, but most appear to have a bore of 15mm (the Proxxon ones are 10mm). I suppose it might be possible to use them with an arbour, but it all seemed a bit of a fiddle.

I was also looking for a tool to do a number of jobs, including cuts to materials 1 inch (25.4mm) or more thick, and the FET maximum is 22mm.

However, if blade supply and cutting depth isn't an issue, then it looks like a nice machine to have, for fairly light-duty use. In the end, I bought a midrange Metabo bandsaw, but if I had a spare £350 knocking about to spend on a small tablesaw, then this would likely be it.
Logged

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Table Saw
« Reply #56 on: September 02, 2012, 02:19:47 PM »

Thanks guys.

Since I am not familiar with these beasties, why would one select (or need) a particular blade diameter? I'm sure it's not as simple as depth of cut, although it would obviously affect that?

Although my father was a carpenter and joiner, I cannot cut wood nicely to save my life. OK for garden stuff and most DIY (although not so much these days!).
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

tedrick

  • Guest
Re: Table Saw
« Reply #57 on: September 02, 2012, 02:40:14 PM »

I apologize in advance for any toes stepped on or umbrage taken - this is meant in a good-natured spirit and is not intended to be a criticism of any other posts on this thread -

there are few internet forum discussions that create more interest than the question, "which table saw?"

our man RobF recently built a beautiful boat with some basic tools including a humble $99 direct drive 8" table saw -

I think the basic cuts required in the cabinetry of a box can be done with the entry level table saw available at the usual places -

The arguments for table saws are the same as the arguments for button boxes: a beginner can make nice music on an entry level Chinese box as well as the most expensive Italian box - the question is, does a beginner need a pro line instrument to begin enjoying music, or would a entry level instrument suffice until the musician has progressed enough to benefit from a higher quality instrument?

Just as box players do not need to start out with a pro level instrument, new woodworking enthusiasts do not need to start out on a artisan level power tool to enjoy their first basic projects.

Finally, as someone said, It's a poor craftsman that blames his tools.
Logged

Prestidigitator

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 448
  • Saltarelle, Hohner, Oakwood Baffetti
Re: Table Saw
« Reply #58 on: September 02, 2012, 02:42:03 PM »

The diameter of the blade is partly determined by the form of the teeth on the blade (shape, depth etc.). These vary according to whether it is for ripping along the wood grain or crosscutting, or indeed for cutting other materials like plastic or metal.

As it would not be very handy to have to keep changing blades for the different cuts in wood, there's usually one tooth form which will serve for both cuts.

My experience, which is derived mainly from boatbuilding and repairing, is that there is not generally much need to change blades unless for different materials, or very hard timber like old seasoned oak.

As Lester says, for work on melodeons a fine blade is probably the best. I imagine that a lot of work involves cutting plywood or thin timber, and a coarse blade will lead to splintering along the cut. It may be my imagination, but I feel that, even when using a cutting "fence" to cut a straight line  (which in theory should make any sort of blade cut straight), a finer blade is more accurate.
Logged

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Table Saw
« Reply #59 on: September 02, 2012, 03:02:56 PM »

I apologize in advance for any toes stepped on or umbrage taken - this is meant in a good-natured spirit and is not intended to be a criticism of any other posts on this thread -
The difficulty here is striking the balance - between a tool good enough to do a decent job, and not so limited that you'd want to upgrade in 6 months, and keeping your feet on the ground.
Melodeon-wise I'm fine with Hohners (admittedly a Liliput mostly) and have no (present >:E) urge to buy a Costalotti.
Concertina-wise I bought a Rochelle to get started and upgraded later to a Marcus, selling the Rochelle for half-price. (In this case I did so knowingly - when I subsequently bought a melodeon the cause was already lost   ::). No disrespect to the Rochelle - it's a beginner's box, did what I wanted and was bought by another beginner. )
So I'm looking for a saw that will do a decent job, on small pieces, that will last me a good while but not have loads of abilities that I'll never use. And while I don't mind getting good tools cheap, I'm wary of buying cheap tools.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."
Pages: 1 2 [3] 4   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal