Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: spring tension  (Read 9928 times)

0 Members and 1 Guest are viewing this topic.

waltzman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 943
spring tension
« on: July 08, 2012, 07:28:05 PM »

I have just gotten a Hohner HA114 four stopper off of Ebay and tuned it for cajun music.  I suspect the spring tension needs to be a bit heavier to keep the large pallets air tight but it feels like the tension is more than it needs to be.   Does anyone have a good technique to recommend for adjusting the spring tension?

Michael
Logged

Martyn

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 455
  • Hohnerohner
    • Martyn White Melodeon Tuning and Repairs
Re: spring tension
« Reply #1 on: July 08, 2012, 11:05:05 PM »

If you are experiencing leaks around the pallets it is far more likely they are not seating properly and need a little adjustment, rather than the spring tension being incorrect.

Martyn
Logged
'Anything from a small repair to a full restoration'.
www.melodeonrepairs.co.uk

waltzman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 943
Re: spring tension
« Reply #2 on: July 08, 2012, 11:28:32 PM »

No.  No leaks.  Just heavy buttons.  Much heavier than my other two and three row Hohners.
Logged

syale

  • The Terrier
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
  • When will this MADness stop?
Re: spring tension
« Reply #3 on: July 08, 2012, 11:54:05 PM »

I disassembled the treble linkages, took out the springs and put a small kink in the spring, only 1/8” off and that softened the buttons tremendously. I can take some pictures if it makes it any clearer. I have shown a representation of what I did.

1. Take the treble end off.
2. Unhook all the springs from the linkages to take the tension away.
3. Remove the screws holding the linkage system to the box and remove the linkage assembly.
4. Withdraw the rod from the assembly taking care about how it all goes together.
5. As you pull the rod out the indvidual buttons/pallets and springs will come out. Lay the linkages out in the order they are removed so they go back in the same place.
6. Put a small kink in the spring. I made a 1/8" adjustment with snipe nose pliers to bend the spring.
7. Put everything back in reverse order.

I should really video stuff like this...
Logged
HA114 C/G/A/D, 2915 G/C. Liliput, Club IIB C/F Dino Baffetti Modell 22 B Twitter: @syale

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: spring tension
« Reply #4 on: July 09, 2012, 02:09:44 AM »

Syale, you got that from Cory, he musta got that from Marc Savoy?  That boy can sure play but he better quit taking accordions apart, his fingers are too delicate for tools.  You can tell him I said that.  ;)

Bryan Lafleur

waltzman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 943
Re: spring tension
« Reply #5 on: July 09, 2012, 02:24:08 AM »

Thanks Syale.  I assume you put the kink in the arm of the spring that goes toward the button?
Logged

syale

  • The Terrier
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 711
  • When will this MADness stop?
Re: spring tension
« Reply #6 on: July 09, 2012, 03:43:32 AM »

Cory told me to put a screwdriver down through the keyboard and bend the spring! My background is instrumentation so I was a little more methodical in my approach. He is a great player. He played in my kitchen when I first bought the accordion and he, very graciously, came to my house to see if it was OK. Really nice guy.

You are correct the kink goes in arm to the button. Hopefully you can see it in the pictures. I forgot to add that you need to remove the grill and the keyboard.
« Last Edit: July 09, 2012, 03:52:53 AM by syale »
Logged
HA114 C/G/A/D, 2915 G/C. Liliput, Club IIB C/F Dino Baffetti Modell 22 B Twitter: @syale

waltzman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 943
Re: spring tension
« Reply #7 on: July 09, 2012, 02:11:39 PM »

Perfect.  Thanks.
Logged

Larus

  • Guest
Re: spring tension
« Reply #8 on: July 10, 2012, 08:47:13 AM »


I should really video stuff like this...
If you could find the time, a video would be much better for us "biffs" to follow :o
Logged

Larus

  • Guest
Re: spring tension
« Reply #9 on: July 10, 2012, 09:39:35 PM »

I decided to have a go at this and to my amazement I managed it and it really works.
The old Hohner 1 row, 4 stop, is now much more responsive and easier to play. No loss of air through the pallets either.
Great tip.
Many thanks ;D
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: spring tension
« Reply #10 on: July 11, 2012, 08:50:27 AM »


4. Withdraw the rod from the assembly taking care about how it all goes together.
5. As you pull the rod out the indvidual buttons/pallets and springs will come out. Lay the linkages out in the order they are removed so they go back in the same place.


A small refinement is to thread a suitable thin rod in from the opposite end as you withdraw the axle rod, this will allow you to keep all the lever arms in place, and will make re-assembly a little quicker.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Larus

  • Guest
Re: spring tension
« Reply #11 on: July 13, 2012, 11:21:08 AM »


4. Withdraw the rod from the assembly taking care about how it all goes together.
5. As you pull the rod out the individual buttons/pallets and springs will come out. Lay the linkages out in the order they are removed so they go back in the same place.


A small refinement is to thread a suitable thin rod in from the opposite end as you withdraw the axle rod, this will allow you to keep all the lever arms in place, and will make re-assembly a little quicker.
Like all good ideas, it's obvious when somebody suggests it.
I'd never even thought of doing this.
Another great tip.
Logged

Sandy Flett

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 709
    • Accordion and Melodeon Blog
Re: spring tension
« Reply #12 on: August 07, 2012, 01:36:19 PM »

I have just carried out syale's procedure on the 8 bass springs and air button spring on my Erica, also using Theo's tip of feeding a wire in as withdraw the rod to keep everything in place. It was a bit fiddly as the whole mechanism would not come out in one piece, so I did it in situ; this also meant I had to do two springs at a time as the rod ends came up against the side of the instrument when only about 60% withdrawn.

However, after a quick tune I am pleased with the result. The buttons are noticeably lighter to play, with no loss of air at the reeds and just a little bit at the air button if I press the bellows hard enough with no buttons pressed.

Thanks for the technical tips and inspiration to try such a thing oneself.
Logged
DG Dino Baffetti Carnival II (plus accordions)
Accordion and Melodeon blog

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: spring tension
« Reply #13 on: August 07, 2012, 01:41:37 PM »

maybe a bit of better pallet leather may sort the air button leak (or put a stronger spring on it) ..

I`d like to lighten the action on a '90s Delicia Hlavacek Heligonka but don`t know if that would cause leaks or the best way to do it. the action is similar to Italian boutique boxes
Logged
Q: How do you cure MAD?
A: Buy more Boxes

Martyn

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 455
  • Hohnerohner
    • Martyn White Melodeon Tuning and Repairs
Re: spring tension
« Reply #14 on: October 19, 2012, 10:00:45 AM »


4. Withdraw the rod from the assembly taking care about how it all goes together.
5. As you pull the rod out the indvidual buttons/pallets and springs will come out. Lay the linkages out in the order they are removed so they go back in the same place.


A small refinement is to thread a suitable thin rod in from the opposite end as you withdraw the axle rod, this will allow you to keep all the lever arms in place, and will make re-assembly a little quicker.

It's a good idea to screw the action to a board before you do this. That will make the whole operation a lot easier.

Martyn
Logged
'Anything from a small repair to a full restoration'.
www.melodeonrepairs.co.uk

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: spring tension
« Reply #15 on: December 31, 2012, 08:12:55 PM »

Spent a useful half hour in the workshop this afternoon putting a kink in the end of the springs of the treble end of my Hohner 1 row. By trial and error I have no got an air tight but appreciably lighter action box  (:) (:)

Etienne

  • Student in push-pull things
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 186
    • ça s'pousse et ça s'tire
Re: spring tension
« Reply #16 on: July 11, 2013, 12:20:37 PM »

I tried this yesterday evening on my 1040 and now feel to have a new box ! THANKS  :||: :||: :||:
Logged
Old hohner and old Dedenis
http://pousser-tirer.blogspot.com

Johnniez

  • Good talker
  • **
  • Offline Offline
  • Posts: 51
Re: spring tension
« Reply #17 on: June 19, 2016, 09:36:59 AM »

I did all 3 ha-114 using this method and the difference in feel and action is enormous.. Thanks ever so much for posting this.

I did screw it down to a board and it went pretty smooth.. Bit of a time with the first box  , bent the rod a couple of times. Other 2 boxes went great.. All 3 now have the same feel.

Johnnie
Logged
Every Day Is A Great Day
Some Are Better Than Others

playandteach

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3526
  • Currently a music teacher in a high school.
Re: spring tension
« Reply #18 on: June 19, 2016, 11:01:14 AM »

Can I do this to the bass end of a Hohner Erika? I've tried replacing the springs, but still too stiff. It's the only reason I'm not picking it up to play more often.
Logged
Serafini R2D2 GC, Serafini GC accs 18 bass

Harmonicatunes

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 261
    • Harmonicatunes
Re: spring tension
« Reply #19 on: June 20, 2016, 11:15:14 AM »

All very interesting. I love the sound of the HA114s, and have a few of them. However the keys do take some effort, which becomes noticeable at higher speeds.

The spring mod described here sounds good, but, as with most things, it is perhaps best left to the experts. Would any of the local fettlers offer such a service? It could perhaps be done by sending the key/pallet assemble only, rather than the entire box.
Logged
Harmonica Player
Just starting with the Box
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal