Melodeon.net Forums
Discussions => Instrument Design, Construction and Repair => Topic started by: Kautilya on April 22, 2010, 04:54:45 PM
-
(whether acrylic or another 'plastic paint' can be used to strengthen, reinforce splitting from inside or also outside (to give a fresh look to) bellows
Painting on paper with acrylic.
Gary Smith (talking about paper preparation for painting with oils to get long life of painting):
The secret to painting on paper and preparing less expensive papers lies in the wonder of the acrylic medium. Acrylic, is essentially a plastic in liquid form. When it dries, and it dries so fairly rapidly, it forms a highly resistant and protective layer of plastic. It also has excellent adhesive qualities, which makes it suitable for a number of painting and preparing purposes.
All that is required are a number of layers of thin acrylic paint or medium on the paper. Three layers should be sufficient, allowing each layer to dry before applying the next. The texture that you might like to create will be determined by the amount of acrylic paint or medium you apply.
….The acrylic paint and medium is basically a layer of plastic that protects the surface against penetration from oil and other elements. Acrylic medium also strengthens the paper. This is the reason why relatively cheaper paper can be used with this method. However, remember that we are still dealing with paper and there are limits to its strength and flexibility.
and??
http://www.polymarine.com/products/parts-and-accessories/flexible-paints-and-antifoulings/superflex-pvc-paint/index.cfm
-
If the bellows are splitting I think any sort of surface coating is only going to be a temporary treatment. But if the bellows are splitting and the only other choice is replacement then you have nothing to loose except the cost of the acrylic.
-
The best thing for bellows splitting on the folds, is to fix from the inside with some flexible heavy paper. Fold the card so you have a new fold and glue in place with the fold flush with the existing one. General PVA is fine for this as the glued surfaces aren't under stress or movement. Cover with new bellows tape and you cant even tell it was split!
-
I use an adhesive linen to repair from the inside. The glue is activated by water. It's used by quality bookbinders. But I don't buy this stuff from UK as it's expensive. I ship it in from the US where it's REALLY cheap. In fact I've thought about importing it and making a killing! It forms the hinges for my sets of concertina bellows - is strong, airtight, and real neat!
AL
-
If the bellows are splitting I think any sort of surface coating is only going to be a temporary treatment. But if the bellows are splitting and the only other choice is replacement then you have nothing to loose except the cost of the acrylic.
But will still be stuck with my chains! (no workers of the world electoral references on melnet!)
On a lighter note (I know u already reacted to an earlier one on this) I wondered if anyone had actually tried it is as a preventive technique, e.g. when tarting up the look of the bellows (all that gusset corner dust etc).
Accepting normal inside splitting repair procedure, I am thinking of the wearing out stage rather than the final splitting stage.....
Dupont seem to be the main makers of this type of elastomer stuff and although they have (as of April 20 2010......) stopped making their Hypalon, there is another 'lettering paint which 'renovates' - in other words, if it is a canvas bellows it would strengthen the fabric skeleton weave ........ further, Polymarine thinks it should work for paper not just canvas. It may depend on whether,, e.g. an old German 'paper' bellows it of paper made from rags etc which are essentially making a paper from a mash of fibres (as opposed to cellulose paper from trees???) Handmade papers are clearly a mish-mash weave as u can see the fibres.
http://www.polymarine.com/products/parts-and-accessories/flexible-paints-and-antifoulings/letterflex-pvc-lettering-paint/index.cfm
Will have a go on an old bellows and see what emerges - if it adds 20 years to the 'fabric' I will surely by then be playing one of your harps O doG, so wont be able to report back............... >:E >:E
-
I once had an old Koch one row that was quite nice, save for the bellows gussets that were dotted with tiny holes, perhaps it had been on the menu for some discriminating insects. I was able to make a repair of sorts using a product which is billed as a liquid electrical tape made by Starbright (http://www.starbrite.com/productdetail.cfm?ID=1090&ProductCat=Home%20Care&ProductSCat=Liquid%20Electric%20Tape%20%28Home%29&ProductSSCat)
It was necessary to remove the bellows and stretch them using clamps and a couple of sticks to keep them extended, and then painting the stuff in two separate thin coatings over the porous areas inside the bellows.
:-X Word of caution here: this product contained some very nasty solvents and should be used outdoors or under a ventilating hood! :-X
This was purely a last ditch repair, and it rendered the bellows reasonably airtite and quite playable.
-
Did you get a good kick when you put on your ventilating hood??!!
[Update (some useful tips also coming in from tina players]
Gave up on Dupont for materials including useless calls to their Euro HQ in Spain - totally disorganised with no-one knowing who does what on paints in their technical divisions- the man at Stevenage paint division has moved.......
However -plus ca change... taking us back to leather cream of old standby, a discussion with the manager of Broodie & Middleton/ (which also Russell & Chapple) suppliers to "artistes" (paint ones!) was that acrylic would not last, BUT a product called MAGIX for restoring distresssed leather (with colours too), was very flexible.
Maybe this could work also on paper bellows, praps. One problem is that it comes in 150ml aerosols with a solvent and dries very fast so the question is whether it will stay wet enough when sprayed into a pot for then brushing on.... B&M only have four colours (incl b&w!) in stock but the (uknown manufacturer, perhaps French - tho could be KIWI shoe polish Co. which is owned by Sara Lee) MAGIX range shows up in France as having 58 different colours.
As part of the exercise is to tart up as well as stabilise the material, that range of colours sounds v good... if it works. Including chocolate, cognac, London and violine....which aint violon I assume...
http://www.cuirs-pratique.com/cuirs-ameublement_reteindre_teinture-finition-spray-bleu-ciel-p-780.html
it is 8 quid in Covent Gdn shop of B&M and I see an importer in L'pool at about five quid plus delivery.
-
I use an adhesive linen to repair from the inside. The glue is activated by water. . . . It forms the hinges for my sets of concertina bellows - is strong, airtight, and real neat!
At the risk of straying into a subject more appropriate to another forum . . .
I picked up a Gallotta concertina recently, on which the "leather" strips along the length of the bellows were made of some kind of plastic-backed cloth. The plastic, inevitably, had disintegrated, so the bellows, which are otherwise pretty good, leaked like a sieve. I went over the leaky "cloth" bits with diluted PVA (with the bellows stretched, as described by J.W.Forrest) and, after a couple of coats, the thing is playable (more or less).
The downside is that the flexibility was reduced - however, a couple of treatments with ArmorAll vinyl treatment has restored this aspect a bit. I'd like to make the thing properly airtight - having re-valved it and done a basic tune, I think it will make a nice enough instrument - but I recognise that it is what it is - and that it isn't worth much, in financial terms.
The question is, where to go next. I'm considering stripping the bellows and replacing the defective lining with leather - if I do that, I'll need to re-do the "bellows tape" strips around the bellows (I'm sure there are proper names for these, but I don't know what they are), and the joints to the ends and intermediate frames - and if I use decent leather for all that, I'll be spending about 50% more than I paid for the instrument, and probably more than it's worth.
I wondered whether the linen you describe could be used, on the inside of the bellows, over the joints that the lining should seal (rather than on the folding joints). Do you think it would have sufficient flexibility? Fitting would be tricky, but not impossible, and properly airtight bellows would be a big improvement.
Thoughts and suggestions welcome!
Regards,
Tony.
-
If you're doing this up only to sell it on then . . .
No, my tinkering isn't based on selling things on (although my dear wife's patience may wear thin if I don't eventually shed a few of my "projects").
I started tinkering with accordions, and (I think) I can do a reasonable job of revalving and waxing. I've ventured to tune one, and it worked out passably well. I suppose I just keep an eye out for something appealing as a next project - the concertina was one, and there are a couple more waiting to be "got around to".
The point about cost was, I suppose, simply to say that I'd rather not spend excessively on it. I know that, if I completely rebuild the bellows, it'll be much better than it ever was - but it's not as if it was ever going to be of such value that "doing a proper job" was the obvious and appropriate way to go. Not sure where the balance lies - so if there's a less expensive way to achieve air-tightness, it's worthy of serious consideration!
Tony
-
You can get all the leather components from David Leese at concertina-spares.com
-
I use an adhesive linen to repair from the inside. The glue is activated by water. . . . It forms the hinges for my sets of concertina bellows - is strong, airtight, and real neat!
At the risk of straying into a subject more appropriate to another forum . . .
I picked up a Gallotta concertina recently, on which the "leather" strips along the length of the bellows were made of some kind of plastic-backed cloth. The plastic, inevitably, had disintegrated, so the bellows, which are otherwise pretty good, leaked like a sieve. I went over the leaky "cloth" bits with diluted PVA (with the bellows stretched, as described by J.W.Forrest) and, after a couple of coats, the thing is playable (more or less).
The downside is that the flexibility was reduced - however, a couple of treatments with ArmorAll vinyl treatment has restored this aspect a bit. I'd like to make the thing properly airtight - having re-valved it and done a basic tune, I think it will make a nice enough instrument - but I recognise that it is what it is - and that it isn't worth much, in financial terms.
The question is, where to go next. I'm considering stripping the bellows and replacing the defective lining with leather - if I do that, I'll need to re-do the "bellows tape" strips around the bellows (I'm sure there are proper names for these, but I don't know what they are), and the joints to the ends and intermediate frames - and if I use decent leather for all that, I'll be spending about 50% more than I paid for the instrument, and probably more than it's worth.
I wondered whether the linen you describe could be used, on the inside of the bellows, over the joints that the lining should seal (rather than on the folding joints). Do you think it would have sufficient flexibility? Fitting would be tricky, but not impossible, and properly airtight bellows would be a big improvement.
Thoughts and suggestions welcome!
Regards,
Tony.
Useful grist to the glue-pot.
A bow first to the professionals who do repairs day in day out. They have to earn a decent living and pay the bills and fortunately they all seem overwhelmed with work as they have queues and queues which is wonderful.
Obviously it is the labour cost which makes up the bulk of repair costs. i can't clean my best shoes as well as the chappy charging five quid outside the Bank of England, but I can do a reasonable job in the 10 minutes from spit to polish as he can in five.
So for those who can live with effectiveness rather than perfection many of these jobs just require time, a bit of patience and practise helps make less imperfect.
Leather - excellent leather (not all pre-cut etc etc which David Leese supplies so nicely) to do this kind of job, can be had for a two or three quid a suare YARD rough offcut.
If u want the address I can dig it out. It is large offcuts from producing ladies thin leather glove/leather art items.
I also collect old leather handbags which are sometimes very thin leather and you will often find lady's leather trousers of thin leather/suede for a couple of quid at boot sale (or for nowt in my case as my sister was about to throw them out....) At almost zero cost you can practise and throw away to your hearts content all day.... and I often take advantages of the greater skill which women's smaller hands have when doing this kind of sometimes picky work e.g. squeezing down a gluey patch on a gusset corner inside a narrow bellows.....
And if you want tapered edges after you have measured and cut your strips then you can use razor, old cuthroat etc etc. **
As a student I had a 3.8litre MkIX Jaguar in two=tone racing green (same model as u saw Marilyn Monroe riding around in) .. I might consider a two tone bellows if I run out of black leather offcuts and have to use some brown or vv...
Embossing: At 14 or so, a couple of us used to repair all the school library books,spines, boards, rexine and leather covers, and we even did gold plated lettering and embossing...no one taught us,we scavanged the basic gear (old steel presses and metal letters which we stuck in the fire or did cold with gold/silver leaf, and they were quite presentable so.....if we could do... we also acquired our own workroom where we drank.... tea etc...
** http://www.concertina.net/forums/index.php?showtopic=11031&view=&hl=strop&fromsearch=1
I believe there are also several accordion part suppliers whose material may suit 'bigger' dimensions of melodeons compared with small tina bellows etc.
Must go -
Off to a session on Hadrian's Wall so haave to put my leather gladiator sandals on before saddling my horse with leather saddle and my horsebox-holding-strap...
http://www.roman-colosseum.info/roman-clothing/gladiator-sandals.htm
-
Leather - excellent leather (not all pre-cut etc etc which David Leese supplies so nicely) to do this kind of job, can be had for a two or three quid a suare YARD rough offcut.
If u want the address I can dig it out.
No firm decision on which way to go forward yet (I'm not in a rush), but a source of offcuts like that would be useful knowledge, if it's not too much trouble to dig out.
I'm also investigating the linen tape - as Al noted, it's a bit pricey, at least from the places I've looked at so far. Almost the price of good leather strip - but capable of different uses, thin and easy to apply without having to dismantle the bellows. It's really handy to know about such things.
Cheers,
Tony
-
be careful which leather you choose, some soft clothing leathers are not at all airtight, pigskin in particular. Sheep nappa should be ok and is readily available in various colours and thickneses.
-
I'm also investigating the linen tape - as Al noted, it's a bit pricey, at least from the places I've looked at so far.
It is pricey over here in the UK 0- but as I said I import mine from the States where its a fraction of the price. I have quite a bit so let me know how much you need and I may be able to help you.
AL
-
I don't know what is regarded as pricey, but I've used this firm, www.ukindustrialtapes.co.uk (http://www.ukindustrialtapes.co.uk/tradecounter/Picture-Framing/shopdisplayproducts.asp?id=116&cat=Gummed+Linen+Archival+Hinging+Tape) which works out at about £1 a metre
-
Much appreciate the advice from all of you - especially Theo's comment about different leathers and the link to the tape supplier.
"Pricey" is indeed rather subjective - the supplier Theo suggested above has not only a big range at what seem like competitive unit prices, but also a reasonable P&P cost. (Some others aren't interested in small orders, or want combined P&P / handling costs that are comparable with the value of a small order.) I've also discovered, in looking at some of these suppliers, that there's a whole range of products out there that I was completely unaware of (= lots of possibilities, but lots of uncertain outcomes!)
Problem is, spend a few pounds on this and a few on that (experimenting with ideas and materials), and it's easy to "prototype" towards the cost of doing a good job without actually getting round to improving the instrument. I'm starting to lean towards the idea of doing the job with proper leather strip - on the basis that it'll only need doing once, and the result is fairly certain.
I'll ponder a while longer, I think.
Thanks again, all.
Tony.
-
Leather - excellent leather (not all pre-cut etc etc which David Leese supplies so nicely) to do this kind of job, can be had for a two or three quid a suare YARD rough offcut.
If u want the address I can dig it out.
No firm decision on which way to go forward yet (I'm not in a rush), but a source of offcuts like that would be useful knowledge, if it's not too much trouble to dig out.
will dig - remind me Monday if not done.
-
be careful which leather you choose, some soft clothing leathers are not at all airtight, pigskin in particular. Sheep nappa should be ok and is readily available in various colours and thickneses.
would glue [erhaps not seal doubtful (naturally leaky) leath when strips are applied?
-
Leather - excellent leather (not all pre-cut etc etc which David Leese supplies so nicely) to do this kind of job, can be had for a two or three quid a suare YARD rough offcut.
If u want the address I can dig it out.
No firm decision on which way to go forward yet (I'm not in a rush), but a source of offcuts like that would be useful knowledge, if it's not too much trouble to dig out.
will dig - remind me Monday if not done.
The Identity shop in Matlock.
I see it is Dec 2008 when I ordered various glues and dyes, applicators, leather restorer, blades, celtic symbols etc etc.
Jackie is the person. She wont remember me but if you say it was someone looking for glove leather offcuts to use on melodeon / concertina bellows and you want to ask her about the same, she will understand. At that date it was pounds 1.50 upwards [[per offcut, depending on size per piece of lightweight gloving leather. I see they normally sell the pukka leather by weight which is always a good sign.
I am sure she will be happy (as she did with us) to send you a sample, but you can always dye to match existing. A mate of mine who is one of the world's greatest antique carpet restorers sometimes uses coloured felt tip pens to match ancient silk with new.... honi soit qui mal y pense... - honey, if you can't afford silk stockings use a permanent marker to run a line down the back of your leg.......
Clearly you need offcuts that will allow you to cut multiple strips of a certain length to go on each binding and all round (or as u need) so mention that. If u did go for a full rebind then u would be best to calculate how much of the same colour leather that would be. But very good at advising so ring up. All contacts on the website.
www.theidentityshop.co.uk
-
Many thanks for that.
The link seems to have changed - that one took me to a search page.
I guess their web address has changed slightly - a quick Google led to http://www.theidentitystore.co.uk/. Definitely the right place, and lots of useful stuff there.
Thanks again,
Tony.
-
Yes, I know the guys at the Identity store in Matlock (a 20 min drive from my house). I recommend them, they also are able to offer items from the Tandy Leather Catalogue. I get all my leather weld glue from them etc. Tell 'em Captain Al sent ya - and you never know ;)
Actually, they've been more than helpful everytime I've ever had need to visit them. I bought a great load of leather that I use as gussetting material for my concertina repairs from them.
AL
-
Having posted about my recent Old Paolo and it's bellows problem I then spotted this very helpful thread. Should have been more thorough in my searches of the site before I posted, anyhoo I'm going to try the Bookbinding tape on the splitting bellows but the real challenge is the gussets as mentioned above which have some pin holes in them. Is there a way to patch or replace these. I'm not looking to make these bellows industrial strength just want to play the little thing on occasion and keep the original bellows.
-
It is possible to patch gussets by gluing thin soft leather on the inside of the gusset
-
It is possible to patch gussets by gluing thin soft leather on the inside of the gusset
That's a good fix.....you can order some thin diamond shaped gussets from BBox and cut out a piece large enough to cover the hole. Use "Loctite" brand flexible adhesive (good for vinyl, fabric and leather) and glue patch from the inside. Patching in the center of the bellows is a bit tricky, but folds near the end aren't too bad. If your original gussets are getting crisp and crumbly, then it might not be worth patching in this manner.
-
Many thanks for that.
The link seems to have changed - that one took me to a search page.
I guess their web address has changed slightly - a quick Google led to http://www.theidentitystore.co.uk/. Definitely the right place, and lots of useful stuff there.
Thanks again,
Tony.
quite right - sorry .. my monocle dropped out and misread store for shop on the compliments slip... but do ring em! Not all is on the site as far as the offcuts and bits and pieces are concerned.
-
Having parked my leaky East German concertina for a few months, I may have a workable solution that could be useful to others:
I had tried diluted PVA, to some benefit, as already noted - however, other circumstances brought something else to my attention. Lurking in my shed was a bottle of Outbound seam sealer, for waterproofing tent seams - must have had it for years. Googling this didn't find any new sources, but Gelert do something that looks to be the same - variable from about £3 to £6, according to source and postage (Amazon and eBay come up in a search).
This stuff is designed to be applied to tent seams, using a "roll-on" tip on the bottle - when dry, you get a thin layer of soft, fairly colourless plastic that stick / penetrates adequately to stop rain getting in through the stitching holes.
The original stuff I had noted that it contained isopropyl alcohol and toluene, so I thought I'd experiment. It didn't dissolve in IPA, and in the absence of toluene (which I seem to recall is nasty stuff), I tried ordinary cellulose thinners - and the goop in the bottle dissolved readily to give a fairly thin liquid. Painted this onto the offending defective cloth binding (inside and out) - one coat each side, and I've got a vast improvement in air-tightness.
Obviously, this is not a suitable approach for a proper restoration, I have no idea how long it might last, and it might give rise to other problems in the future - but, for those who want to improve the playability of something that's not worth a "proper" repair, it does seem to be an option.
Suitably thinned, it may also be capable of penetrating paper or thin card, plasticising it a bit and improving strength - but I haven't tried that.
Comments welcome, as ever.
Tony
-
Having parked my leaky East German concertina for a few months, I may have a workable solution that could be useful to others:
Comments welcome, as ever.
Tony
More! More!
Following start of this thread I secured the yellow plastic paint.
I painted some bottom seams last week which showed part straight line 'cracking' in the 'crack' of the fold when bellows pulled out. (Colour almost matches)
I need to put another coat on the test cracks as 'blackness' of cracks showing through new paint still.
two BUTS
but1. The gussets I now (stupidly) realise are not painted but their original cardboard colour. So I do not know whether to try painting them yellow (bottom back, out of sight for test) or see if I can find an appropriate plastic paint cardboard colour.
but2. I kept blobbing the damn yellow paint on the black binding,as I held the bellows open with other hand. - I suppose I should be putting some masking tape along the binding...
or is there a quicker approach???
3.Fortunately it wipes off easily with thumb and finger without leaving too much of a trace on the black (maybe I have to paint that later anyway though masking tape question still applies to keep black off the yellow). Or I could use my black dye on binding where looking rough and then spray clear car plastic silicone 'shine-up' spray on the black and that won't be a problem if it goes on the yellow.....hmmmmm!?
4.I used to use a trick of painting a line by holding a plastic ruler in place over the not-to-be-painted part........though often it leaked -- using edge of thin cardboard worked too and easier to throw away wet bits?? I might try cutting some on paper guillotine to get a sharp edge.
5.My sister is an afficionado of the little square sponge paint applicators for door jambs and window frame to glass wood sections and etc, but I never seem to get a good result (perhaps I need I need sing and play a Formby Uke at same time to get the rythm).
6.After painting a fold I then popped a variety of old biros in the crack to keep the two sides of the fold away from each other while they dry. I am reminded that when putting new sealant around the bath you are supposed to stand in it so sealant fully fills the gap and folds in on itself when you get out and bath 'lifts' up. Coz without doing that, when you use bath after sealant dried, you will physically pull down the bath away from the new sealant and may open up a gap.......
If i paint all the folds I calc I have 9 foot length x 2 inches depth of bellows to do........ :Ph :Ph
Taken photos of pilot process thus far but not ready to put up yet.
I have been playing the box a little in the interim but forgot to look till your post to see if any new/re-emerging splits in newly painted section; test area looks ok thusfar.
Finally intrigued at what leak-evaluation-technique you used to notice big improvement post canvas-proofer?
7. I think my real problem is not the dilettante-leaking fold work, but a gale blowing through my outer row; coz when hit a button there it plays fine but vast amounts of air escape, audibly.. The Grand Troll heard it too at Wem and we wondered whether the (ok=looking) pads are perhaps sitting just too thin for the job they need to do -Maybe I will record some leak sound (it's that loud!) when I sort out the photos. :Ph :Ph That is a C Row so perhaps it could be some airheads trying to escape to follow the Freebreather Leader in his C campaign.........
-
Glad to see your experiments are having some success!
Anything on the bellows seems to involve a lot of work - I looked quite carefully at what would be involved if I tried relining with leather (a proper job!), and there seemed an awful lot of opportunity to get things wrong, which was (partly) what put me off trying that as a first step. I considered making or buying new bellows, as well - repair / replacement remain options, but I'd rather avoid either.
As I said before, the instrument was playable before the latest round of "improvements", but only just - and it needed a lot of air button use to keep a tune going, so it was clear I needed to either do something about it or sell it on and call it a day. I did a check for leaks before the latest "fix" (dusting of talcum powder round the outside of the bellows, then squeeze and see where the leaks were) - I had over 50 individual leaks! If your bellows are as bad as these were (and remember even this was significantly better than when I got the thing) it's quite easy to measure improvement - you just notice how much less you need the air button!
With the bellows compressed and the concertina suspended vertically from one strap, it now takes 10 seconds or so for the leaks to allow the bellows to fully extend - from recollection, that's two to three times as long as it was before the latest "treatment". (This may not be a good thing to do, btw: the straps weren't terribly strong, and I now need to make a new one!)
When I've worked on the bellows, I've used two sticks (one each side of the instrument), and with some string and small wire hooks (through the holes for the bellows pins) held the bellows in an extended position (not too tight). The sticks can go either inside the bellows or outside, according to where you want to work, and you can leave things to dry quite happily.
One thing I should have pointed out about my latest method - it stinks! The fumes from the thinners are seriously not good for you, and it should really be done with LOTS of ventilation. Also, several days on, the concertina still fills the room with the smell of thinners - it's clearly going to take a while to go away!
Keep up the good work!
Tony
-
Tony
Mine's longer than yours - 13 to 15 seconds. That said i do have too much air button demand if I pull in left right and hold all the buttons down (for haunting slow songs..........) but praps not as bad as yours was.
Emilio Allodi showed me the other week a ''tight' begallows - you could not push it in at all.
I may have to advertise for an expert hangman on Melnt for accurate drop to weight to knot ratio. Le Jig Stepdance de Pierrepoint springs to mind.
.
Like the string and sticks - will bear in mind.
Talc -clever - but, hmm -- what about cleaning it off black areas after?
I was tinkering again with idea of trying dhoop (there were lots of no noes last time I suggested it on Cnet, in terms of 'bits' of smoke getting in the reeds, but I don't see that....I drop ash all the time on my machine from fag end as I sing along to my own accompaniment a la azzplayer and my page turner smokes and is a player too:
http://tinyurl.com/33yqmey
The dhoop would be placed under bottom of one open end (leaving top closed). It burns very slowly and cold after it gets started and the cone ones sit nicely (dont use joss stick) leaving hands free to spot leaks (if it works!) Or a mosquito coil with stand - you can break bits off the coil and light them.
http://www.roamingfox.co.uk/Mosquito-Coils-pr-16414.html?gclid=CNLeup-X2qMCFQX92AodEHFg9w
http://www.theincensestore.com/online_store/chamundeswari_dhoop_sticks_24_sticks_loban_2.cfm
Have been using talc to track where leak starts around my diesel fuel pump on the car and it is v effective. But does not solve the drip!!
Has your playing improved after each smelling session? - I often wondered about using a felt tip pen at a session rather than a Vick's nasal inhaler - to get that extra craic as the evening wears on (http://www.pharmacyfirst.co.uk/medicines/vicks-inhaler-nasal-/prod_1475.html)
Till later
:|glug :|glug
-
Paint - type.
Shots showing typical cracks in old 'paint' of some of the folds (and different colour of the gusset)
Painted shot (which need another coat and cleaning up the lines to binding).
(sorry two of the same painted and can't delete it.....)
Keep apart pens! in next post
-
Keep apart pens!
-
I'm not sure why you are going to all this trouble. From the pictures it seems that the cracks you are dealing with are just in the yellow paper which is normally only a decorative component. Maybe there is more that the picture can't show of course, but I think I preferred the visible cracks to the somewhat streaked paint!
-
I'm not sure why you are going to all this trouble. From the pictures it seems that the cracks you are dealing with are just in the yellow paper which is normally only a decorative component. Maybe there is more that the picture can't show of course, but I think I preferred the visible cracks to the somewhat streaked paint!
For fun!
My mate needs a whitewall tyre for his 1998 Roller for MOT. new one tyre is 220 quid delivered.
He used to spray Rollers at Park Royal plant, so I told him to paint a white rim around a plain tyre (new tyre 60 quid) coz no one will know the difference. "I will!" he said........... But I think I am going to win him round....
There is more than the picture shows -- there's yellow gold in them thar cracks.
Streaked? - quite right - that's my next cleanup challenge. The test at the moment is about reinforcement and filling in the cracks to try flexibility.
The final finish, if I repaint the whole bellows, will be done Pristine Chapel style, under the supervision (free) of my jobbing painter mate Michele Angelo from the Vatican Sopranis! ( (flodA is not free)
It will also play a helluva faster with new yellow striping.
Point is, the yellow on the upper bellows and front and back are okayish but part stained, some glue showing on repaired 'paper' corners next to metal surrounds etc etc and are ready for a good repaint. The pics show the underneath which is still quite nice).
To redo the "paper" covering (even if it is decorative, and tho I may be wrong..... I think it is structural.) on 9 foot of bellows (unlike popping papers on a tina) would be a really major exercise as on this box it is held under the binding, so all that would have to be redone too - I'll ask The Box Place to quote professional price and let you know! >:E >:E
That said, you know I am always ready to learn from the Master Up There... ;) ;)