Melodeon.net Forums

Discussions => Instrument Design, Construction and Repair => Topic started by: Martin J on August 15, 2011, 09:49:38 AM

Title: Bass buttons rattle in their hole
Post by: Martin J on August 15, 2011, 09:49:38 AM
I have a box with a very annoying tapping from the bass buttons caused by the shaft rattling in the hole when the button is pressed.  It is a perloid finish.  I think sleeving the hole would correct this.  I am considering a hard felt liner or should I be looking at a more engineering solution with oilite bushes ?

Any advice / experience would be very helpful.
Title: Re: Bass buttons rattle in their hole
Post by: Steve_freereeder on August 15, 2011, 10:27:38 AM
I would recommend purpose-made bushing felt, such as that used for bushing concertina buttons. It is fine, dense and hard wearing. Available from David Leese, concertina repairer and parts supplier based in North Wales:
http://www.concertina-spares.com

Specifically this stuff:
http://www.concertina-spares.com/catalogue11.htm

One piece is more than sufficient for a melodeon.
David is very efficient in fulfilling orders; highly recommended.
Title: Re: Bass buttons rattle in their hole
Post by: Martyn on August 15, 2011, 01:12:57 PM
It's worth mentioning that you will have to use a tapered reamer to enlarge the holes first.

Martyn
Title: Re: Bass buttons rattle in their hole
Post by: Martin J on August 16, 2011, 10:37:07 AM
Thanks to Steve and Martyn.  Getting the job in hand now.

Martin
Title: Re: Bass buttons rattle in their hole
Post by: Lester on August 16, 2011, 07:15:10 PM
Charlie Marshall has, in stock, some self adhesive bushing felt that I have used, successfully for this very job.
Title: Re: Bass buttons rattle in their hole
Post by: Graham Spencer on August 16, 2011, 07:31:46 PM
Charlie Marshall has, in stock, some self adhesive bushing felt that I have used, successfully for this very job.

Does he? Can't track it down on his website............maybe I'm looking in the wrong place.
Title: Re: Bass buttons rattle in their hole
Post by: Martyn on August 16, 2011, 07:38:02 PM
It's here http://www.cgmmusical.co.uk/CGM_Musical_Services/Felt_Leather_Pallets.html
Third row down in the middle 074B.

I personally wouldn't use this for button bushing, as it's not dense enough and therefore would have a very limited life.
Far better to use a proper bushing or bearing felt glued in with PVA.

Martyn
Title: Re: Bass buttons rattle in their hole
Post by: Lester on August 16, 2011, 09:25:10 PM
I'll give David Leese's stuff a go then, never let it be said I am not willing to learn  ::)
Title: Re: Bass buttons rattle in their hole
Post by: Martin J on August 16, 2011, 10:14:32 PM
Melnet wonderful as ever.  Thanks for the invaluable info.  I'll try the 'ard stuff' having suitable reamed me oles. (:)
Title: Re: Bass buttons rattle in their hole
Post by: Martyn on August 16, 2011, 10:36:11 PM
An anovver fing innit bro.  8)

Don't forget to cut the felt diagonally across the weave to prevent 'threading'.

M.

Title: Re: Bass buttons rattle in their hole
Post by: Martin J on August 17, 2011, 08:53:38 AM
Thanks Martyn.  There was no danger of me forgetting as I didn't know, so I am again grateful for the help.
Title: Re: Bass buttons rattle in their hole
Post by: Lester on August 17, 2011, 08:59:27 AM
An anovver fing innit bro.  8)

Don't forget to cut the felt diagonally across the weave to prevent 'threading'.

M.



Just ordered some from Dave Leese and I note he supplies it in a trapezoidal shape sort of forcing you to cut it on the diagonal.

(http://www.concertina-spares.com/imag/bushing.jpg)
Title: Re: Bass buttons rattle in their hole
Post by: MadDogMurdock on December 12, 2011, 01:32:48 AM
Not sure if anyone can help me, but I'm interested in getting some of this bushing felt in the USA.  Any of you have a producer name on that felt or any specifics that I might be able to track it, or something akin to it, down over here?  Thanks
Title: Re: Bass buttons rattle in their hole
Post by: Steve_freereeder on December 12, 2011, 01:39:50 AM
Not sure if anyone can help me, but I'm interested in getting some of this bushing felt in the USA.  Any of you have a producer name on that felt or any specifics that I might be able to track it, or something akin to it, down over here?  Thanks
Contact David Leese directly. He will ship stuff to the US.
http://www.concertina-spares.com
Title: Re: Bass buttons rattle in their hole
Post by: Theo on December 12, 2011, 08:06:24 AM
Not sure if anyone can help me, but I'm interested in getting some of this bushing felt in the USA.  Any of you have a producer name on that felt or any specifics that I might be able to track it, or something akin to it, down over here?  Thanks
Contact David Leese directly. He will ship stuff to the US.
http://www.concertina-spares.com

Indeed he does, but you can also get it from piano parts suppliers if you happen to know of one local to you.

The harder task is to find a suitable reamer.  Don't be tempted to used an ordinary twist drill which is likely to tear splinters out of the edge of the hole. 

And...   if you remove the rods by straightening the small pins which act as a hinge to the lever then there are two things to be aware of:
1) you can't bend the pins much without a risk of breaking them
2) if you do have to replace some, don't use any material that is thinner than the original or you will just introduce another source of noise.

Mainly for these two reasons I think it better to remove the buttons from the rods, and take out the whole mechanism.
Title: Re: Bass buttons rattle in their hole
Post by: Steve_freereeder on December 12, 2011, 08:54:51 AM
I think it better to remove the buttons from the rods, and take out the whole mechanism.
On a Hohner Erica how do you remove the buttons from the rods? They appear to be glued firmly in place.
Title: Re: Bass buttons rattle in their hole
Post by: Theo on December 12, 2011, 09:06:22 AM
I think it better to remove the buttons from the rods, and take out the whole mechanism.
On a Hohner Erica how do you remove the buttons from the rods? They appear to be glued firmly in place.

They are a tight push fit.  They are not easy to remove or replace, but I believe worth the effort to get the best possible result with this job.
Title: Re: Bass buttons rattle in their hole
Post by: Martin J on December 12, 2011, 09:06:50 AM
When I re did the pallet felts on an Erica I held the mechanism down very firmly and removed the screws then it will just lift out.  Be careful of the springs pushing the whole mechanism. Replacing is fidley but very doable.
Title: Re: Bass buttons rattle in their hole
Post by: Theo on December 12, 2011, 09:08:24 AM
Yes on an Erica that will work,  but not on models with mushroom bass buttons.
Title: Re: Bass buttons rattle in their hole
Post by: Steve_freereeder on December 12, 2011, 09:16:36 AM
On a Hohner Erica how do you remove the buttons from the rods? They appear to be glued firmly in place.

They are a tight push fit.  They are not easy to remove or replace, but I believe worth the effort to get the best possible result with this job.
Thanks, Theo!

When I re did the pallet felts on an Erica I held the mechanism down very firmly and removed the screws then it will just lift out.  Be careful of the springs pushing the whole mechanism. Replacing is fidley but very doable.
Thanks Martin, but I've tried that with my Erica and found (on my particular instrument anyway) there is still not enough clearance to lift the mechanism out. Perhaps there are slight differences in internal dimensions from one instrument to another?

NB - I also released the springs from their little anchor hooks before I removed the screws which hold the mechanism in place. That way there is no danger of the spring tension ripping the screws out of the threads in the wood.
Title: Re: Bass buttons rattle in their hole
Post by: pikey on December 13, 2011, 02:32:27 PM
I need to bush the bass buttons on my Dino Black Pearl 3, where the buttons move all over the place.  The buttons don't seem to want to come off the levers though. Are they glued on or just pushed on?

Cheers
Kevin
Title: Re: Bass buttons rattle in their hole
Post by: Martyn on December 13, 2011, 02:50:17 PM
Kevin,
It's probably best to unscrew the buttons then remove the action with the pistons attached. It can be a bit fiddly getting the pistons to go back in the holes though. It makes it easier if you turn the box upside down to do this.

Martyn
Title: Re: Bass buttons rattle in their hole
Post by: pikey on December 14, 2011, 05:32:49 PM
Thanks Martyn. Do I need to stand on my head as well?  (:)
Title: Re: Bass buttons rattle in their hole
Post by: Martyn on December 14, 2011, 07:34:22 PM
Thanks Martyn. Do I need to stand on my head as well?  (:)

If you think it will help!   ;D

Martyn
Title: Re: Bass buttons rattle in their hole
Post by: pikey on December 19, 2011, 11:41:56 AM
Quick question  - should I ream from the outside in, or the inside out?   
 ???
Title: Re: Bass buttons rattle in their hole
Post by: Martyn on December 19, 2011, 11:53:18 AM
Quick question  - should I ream from the outside in, or the inside out?  
 ???

If you are using the same thickness felt as the original you shouldn't need to ream the holes. Perhaps just enough to remove any old felt/glue residue but be careful not to enlarge them.
I always ream from the outside in.

Martyn
Title: Re: Bass buttons rattle in their hole
Post by: pikey on December 20, 2011, 02:02:45 PM
Thanks, and Happy Xmas!
Title: Re: Bass buttons rattle in their hole
Post by: Graham Spencer on December 20, 2011, 02:40:37 PM
Quick question  - should I ream from the outside in, or the inside out?  
 ???

If you are using the same thickness felt as the original you shouldn't need to ream the holes. Perhaps just enough to remove any old felt/glue residue but be careful not to enlarge them.
I always ream from the outside in.

Martyn

Using a tapered reamer, shouldn't you work from both sides if you want a parallel-sided hole?
Title: Re: Bass buttons rattle in their hole
Post by: Theo on December 20, 2011, 03:32:40 PM
If you want a parallel sided hole you would need a parallel reamer!
If you ream from both sides you will get closer to parallel, but still not parallel.  Since the bushing is a soft material you can accommodate some taper.
SimplePortal 2.3.5 © 2008-2012, SimplePortal