Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2] 3   Go Down

Author Topic: Sibylla Brand GCF - Bellows problem  (Read 11472 times)

0 Members and 1 Guest are viewing this topic.

Daddy Long Les

  • Forum Librarian
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 1016
    • Daddy Long Les
Re: Sibylla Brand GCF - Bellows problem
« Reply #20 on: August 08, 2012, 11:33:58 AM »

I`ve not seen inside the bass end but Theo & Owen will know if a Pokerwork airbutton / pallet mech could be fitted.

http://www.cgmmusical.co.uk/CGM_Musical_Services/Hohner_Parts.html#13

Don't think so as there's not enough room for the pallet.  I'll try and take a photo to show you.

Ok - pretty poor quality photo but you can see the double hole that was drilled for the air button pallet with the masking tape behind it.  To the right of this you can see the housing for the air button.  You can see the open slot where the retaining pin goes - the other side (on top of this)  as you can see, has been snapped off.  Between the inner side of the box and the housing is a clearance of about 3/4 inch so not sure if a Pokerwork mechanism would fit in here.  The area of the double hole is 1 inch x 1/2 inch.  This box currently has a push-in type button rather than a slide-down type.
Logged
Castagnari Lily DG,  Hohner Erica DG, Hohner Erica GC, Hohner Liliput Bb Eb, Hohner 4 stop in C

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Sibylla Brand GCF - Bellows problem
« Reply #21 on: August 08, 2012, 11:47:39 AM »

My first thought would be a glue repair (assuming you still have the top) then make up some plates to reinforce across the joint, screw or bolt them on. Personally I might use old glass fibre circuit board material which can be glued, but any thin sheet metal would do.

However, it's tricky to get a clear mental picture of scale from this distance.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Daddy Long Les

  • Forum Librarian
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 1016
    • Daddy Long Les
Re: Sibylla Brand GCF - Bellows problem
« Reply #22 on: August 08, 2012, 12:01:40 PM »

Ok  - here's a photo of the actually air button which, because of the need to reach the slot opening on the bass plate, has obviously been built up at some point. As you can see from the pallet to the top of the button is getting on for about 2 inches.  I just looked at my Erica and although the height is about the same, the surface area needed to mount the metal frame and for the pallet to go down is far greater than I have here on this little box.  Oh well, never mind I'm sure something can be done.
Logged
Castagnari Lily DG,  Hohner Erica DG, Hohner Erica GC, Hohner Liliput Bb Eb, Hohner 4 stop in C

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Sibylla Brand GCF - Bellows problem
« Reply #23 on: August 08, 2012, 12:03:40 PM »

I'm fairly certain that a Hohner air valve will not fit on that space.
The choices are either repair the damaged wooden block, or make a new one.  It is the fragile nature of components like this that makes me avoid Saxony built boxes!
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Daddy Long Les

  • Forum Librarian
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 1016
    • Daddy Long Les
Re: Sibylla Brand GCF - Bellows problem
« Reply #24 on: August 08, 2012, 12:05:44 PM »

My first thought would be a glue repair (assuming you still have the top) then make up some plates to reinforce across the joint, screw or bolt them on. Personally I might use old glass fibre circuit board material which can be glued, but any thin sheet metal would do.

However, it's tricky to get a clear mental picture of scale from this distance.

Yep I get your drift.  The only trouble is the bit that broke off is really small - about 3/8 by 1/4 inch so I don't thing screwing into it is an option.  Thanks for your suggestion though. (:)
Logged
Castagnari Lily DG,  Hohner Erica DG, Hohner Erica GC, Hohner Liliput Bb Eb, Hohner 4 stop in C

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Sibylla Brand GCF - Bellows problem
« Reply #25 on: August 08, 2012, 12:15:37 PM »

If you have the technology - and possibly an old baked beans tin or something (beer cans, sadly, may not be strong enough - but don't let me stop you experimenting with a few), you could form an inverted U-shaped yoke over the top with a small bolt lower down to fix.

Personally I think a repair with a decent woodworking glue would be strong enough, but it it were to break again it would be harder to repair next time so I would be looking at belt and braces.

You might just be able to glue another shaped bit of wood alongside it.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Daddy Long Les

  • Forum Librarian
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 1016
    • Daddy Long Les
Re: Sibylla Brand GCF - Bellows problem
« Reply #26 on: August 08, 2012, 12:17:07 PM »

I'm fairly certain that a Hohner air valve will not fit on that space.
The choices are either repair the damaged wooden block, or make a new one.  It is the fragile nature of components like this that makes me avoid Saxony built boxes!

"Make a new one" gets my vote.  A job for Martyn upon his return methinks.  Totally agree about the build quality etc. and if it wasn't for the sound I would have probably deposited this box in the bin by now and put it down to experience.  Still, if nothing else, it's taught me loads about the inner workings so that's got to be a good thing, right?

Again, thanks to everyone for your input.

I'll re-post when I get it sorted out and I'm sure I'll feature the box in a future blog.
Logged
Castagnari Lily DG,  Hohner Erica DG, Hohner Erica GC, Hohner Liliput Bb Eb, Hohner 4 stop in C

Daddy Long Les

  • Forum Librarian
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 1016
    • Daddy Long Les
Re: Sibylla Brand GCF - Bellows problem
« Reply #27 on: August 08, 2012, 12:21:37 PM »

If you have the technology - and possibly an old baked beans tin or something (beer cans, sadly, may not be strong enough - but don't let me stop you experimenting with a few), you could form an inverted U-shaped yoke over the top with a small bolt lower down to fix.

Personally I think a repair with a decent woodworking glue would be strong enough, but it it were to break again it would be harder to repair next time so I would be looking at belt and braces.

You might just be able to glue another shaped bit of wood alongside it.

Hmm -  I understand where you're coming from here Malcolm but as I don't really have the technology and I'm quite fond of my fingers I think I'll leave this to someone who's a bit handier than me.  (That's about 99.999999% of the human race btw!!).  Very many thanks with all your kind help with this problem though.
Logged
Castagnari Lily DG,  Hohner Erica DG, Hohner Erica GC, Hohner Liliput Bb Eb, Hohner 4 stop in C

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Sibylla Brand GCF - Bellows problem
« Reply #28 on: August 08, 2012, 12:24:47 PM »

I`m sure Martyn will be able to sort it .

Unwittingly you`ll have contracted MFD (Melnet Fettling Disease), OK Sybil may end up at Martyn`s for sorting but bet your boots your interest will be perked up when you see a tatty Hohner on the cheap which needs  bits doing - before long you`ll have fingers covered in reedwax, dead reedvalves bunging up the dyson, the smell of Wax, PVA and polish wafting through the house and a hot-line to Charlie Marshall for bits.
Logged
Q: How do you cure MAD?
A: Buy more Boxes

Daddy Long Les

  • Forum Librarian
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 1016
    • Daddy Long Les
Re: Sibylla Brand GCF - Bellows problem
« Reply #29 on: August 08, 2012, 12:32:32 PM »

I`m sure Martyn will be able to sort it .

Unwittingly you`ll have contracted MFD (Melnet Fettling Disease), OK Sybil may end up at Martyn`s for sorting but bet your boots your interest will be perked up when you see a tatty Hohner on the cheap which needs  bits doing - before long you`ll have fingers covered in reedwax, dead reedvalves bunging up the dyson, the smell of Wax, PVA and polish wafting through the house and a hot-line to Charlie Marshall for bits.

You don't know me Adam or you wouldn't be saying this!!  I've always been a "I play 'em, I don't fix 'em" kind of guy.  I've earned my living all my life from teaching the guitar.  Yes, I can change strings but I leave truss rod adjustments and fret dressing to those who know about these things.  The only reason I've got under the hood with this box is that I couldn't get it looked at by an expert and being a school teacher, I've got plenty of time on my hands. ;) ;) ;D ;D
Logged
Castagnari Lily DG,  Hohner Erica DG, Hohner Erica GC, Hohner Liliput Bb Eb, Hohner 4 stop in C

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Sibylla Brand GCF - Bellows problem
« Reply #30 on: August 08, 2012, 02:05:18 PM »

Quote
You don't know me Adam or you wouldn't be saying this!!  I've always been a "I play 'em, I don't fix 'em" kind of guy. 

So had I with boxes ...........  before I discovered Melnet, you had "A BOX" (in my case a big wardrobe of a PA) , Make that two if you did a lot of pubbing as a small one id beneficial, if it went wrong (or not if a decent one and bought from a reliable source) then you sent it to one of a few places who fixed them and you`re back on the road again ....... I fixed Synths because I had to but the box was for playing .....

Then there was Melnet and my first poke inside freeing a sawdust filled reed in a Chinese Stella PA . then it was tinkering an old 1 row Hohner back to playability and so on and so on . Never say Never Les even though you`ve been on the forum a long time, one sniff of reed wax and you`ll be hooked  - maybe best to say NO now ;D
« Last Edit: August 08, 2012, 02:07:37 PM by Adam-T »
Logged
Q: How do you cure MAD?
A: Buy more Boxes

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: Sibylla Brand GCF - Bellows problem
« Reply #31 on: August 24, 2012, 12:23:03 AM »

If you check all the suggestions and still have air loss then you might have bellows that have become porous.  I found this recently on my 1930s Hohner Club.  Minute amounts of air were escaping from numerous places in the gussets and in the internal fold lines, and adding up to sugnificant air loss with the same symptoms you described. New bellows made a huge difference,  but you need to be sure before committing to a major spend like new bellows.

I'm worried that's happened with my Preccy :( There always seems to be some leak with the bellows. Last time it happened was earlier this year, when I got it out of the box and it was gulping air. In desperation I waxed the joins inside - something which I now know that I categorically should not have done, but in my defence it was right before a gig and I needed the damn thing to play. I think that it made a difference, but I will be sending it off to Mike soon :(
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

Idelone

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 135
  • Now that's what I call a-peeling.
Re: Sibylla Brand GCF - Bellows problem
« Reply #32 on: August 24, 2012, 11:01:53 AM »

Les, just a thought re tracing your leak. Try this:

1. Open the bellows to full extent.
2. Insert appropriate flexible pipe into air-hole and seal around it.
3. Attach other end of pipe to gas cooker and fill bellows with gas.
4. Remove pipe from box and seal air-hole.
5. Compress bellows with one hand while using a lighter to trace the leak.
6. The escaping gas will be ignited where it's leaking.
7. Easy; job done.

I doubt that there will be much left of the bellows after this, nor possible the box, dry wood really burns, you know, but at least you will know where the leak originated from.

You might want to do a risk assessment first, and it's not something that others should attempt at home; this is a job for a professional.

I do have a chain saw should you really be desperate.

Cheers, Ian
Logged

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Sibylla Brand GCF - Bellows problem
« Reply #33 on: August 24, 2012, 11:13:13 AM »

I would suggest holding the lighter on the side away from you. That will make it easier to tell if it's the bellows, or your clothing, that's on fire.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Owen Woods

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3894
  • melodeonmusic.com
    • The website and blog of Owen Woods
Re: Sibylla Brand GCF - Bellows problem
« Reply #34 on: August 24, 2012, 11:15:23 AM »

I think that it's very sad that people are advocating such hi-tech methods when there are much simpler, easier ones available. Simply fill a bathtub with water, place the box in it, squeeze and look for bubbles.
Logged
Bergflodt D/G 4 voice, Saltarelle Bouebe D/G, Super Preciosa D/Em, Hohner Impiliput B/C+C#

Latest blog post: In Any Weather

http://melodeonmusic.com/blog

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Sibylla Brand GCF - Bellows problem
« Reply #35 on: August 24, 2012, 11:18:20 AM »

However good an idea, there's always someone wants to pour cold water on it.  ::)
« Last Edit: August 24, 2012, 11:24:37 AM by malcolmbebb »
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Sibylla Brand GCF - Bellows problem
« Reply #36 on: August 24, 2012, 11:28:02 AM »

Quote
In desperation I waxed the joins inside - something which I now know that I categorically should not have done, but in my defence it was right before a gig and I needed the damn thing to play.

A certain "Melodeon repairer" (who is NOT a regular of this parish) has done that to a HA114 I`ve now got , the joints on the bellows frames and end boards on these Sieves of boxes are reknown for widening and this guy has filled the thing with reed wax, I`ve no idea how to reverse what he`s done and if when I`ve finished renovating it, it`s still more of a sieve than these things usually are, I`ve no alternative to use wax also as PVA doesn`t stick to reedwax :( . any ideas would be gratefully received.
Logged
Q: How do you cure MAD?
A: Buy more Boxes

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Sibylla Brand GCF - Bellows problem
« Reply #37 on: August 24, 2012, 11:53:47 AM »

A small triangular section fillet of wood, pinned in place?
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Daddy Long Les

  • Forum Librarian
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 1016
    • Daddy Long Les
Re: Sibylla Brand GCF - Bellows problem
« Reply #38 on: August 24, 2012, 11:56:06 AM »

Les, just a thought re tracing your leak. Try this:

1. Open the bellows to full extent.
2. Insert appropriate flexible pipe into air-hole and seal around it.
3. Attach other end of pipe to gas cooker and fill bellows with gas.
4. Remove pipe from box and seal air-hole.
5. Compress bellows with one hand while using a lighter to trace the leak.
6. The escaping gas will be ignited where it's leaking.
7. Easy; job done.

I doubt that there will be much left of the bellows after this, nor possible the box, dry wood really burns, you know, but at least you will know where the leak originated from.

You might want to do a risk assessment first, and it's not something that others should attempt at home; this is a job for a professional.

I do have a chain saw should you really be desperate.

Cheers, Ian

I've heard of gallows humour - I guess this is bellows humour!!! ;D ;D ;D ;D
Logged
Castagnari Lily DG,  Hohner Erica DG, Hohner Erica GC, Hohner Liliput Bb Eb, Hohner 4 stop in C

Idelone

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 135
  • Now that's what I call a-peeling.
Re: Sibylla Brand GCF - Bellows problem
« Reply #39 on: August 24, 2012, 12:49:36 PM »

However good an idea, there's always someone wants to pour cold water on it.  ::)

Right on, Malcolm. I think it's called professional jealousy.
Logged
Pages: 1 [2] 3   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal