Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: leathers  (Read 2326 times)

0 Members and 1 Guest are viewing this topic.

KWIMER

  • Member
  • *
  • Offline Offline
  • Posts: 12
leathers
« on: November 08, 2008, 03:36:27 AM »

I am attempting to renovate an old two row M Hohner.  The leathers on the reed blocks are curled.   Is there some way to straighten them without removing them?

I'm new here and appreciate any help I can get.

Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: leathers
« Reply #1 on: November 08, 2008, 11:27:02 AM »

Hi and welcome.

There is a simple way to straighten the leathers, but there are several reasons why it of limited use.

To straighten the leather place a piece of thin, flat, stiff material under the leather, stiff card is ok, thin plastic or metal is better.  Then gently run the flat tip of a small screwdriver along the length of the leather, starting at the fixed end.  This has the effect of gently stretching the top surface of the leather and will almost always get the leather flatter than it was.

The first down side is that with old leather the curl is only part of the problem.  The leather will also have lost its elasticity and will not move as freely as it should, and with use they will tend to revert to their old curved state.  The second problem is that the leathers on the underside of the reeds will also need attention and they are not accessible.

The only way to fix things so that the reeds can give their best is is to do a full reed overhaul which means taking off all the reeds, removing all traces of old wax from reeds and reedblocks, discard all the old valves, clean the reeds to remove rust and dirt then fit a new set of valves, wax the reeds back onto the blocks with fresh wax and retune the reeds! :o
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

KWIMER

  • Member
  • *
  • Offline Offline
  • Posts: 12
Re: leathers
« Reply #2 on: November 08, 2008, 08:03:35 PM »

thank you.   I will give it a try.   The reeds don't seem to be waxed to the block, they have a leather gasget between the reed and the block.  Is this normal? 
the Hohner if very old, and needs bellows attention also.  It seem someone has glued the bellows to the treble side, so it need to be cut away before I can get to work on the treble side.

Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: leathers
« Reply #3 on: November 08, 2008, 09:21:03 PM »

Firstly, are you sure that the bellows has been glued to the frame.
Many older Hohners have two large screws under the grille, which hold the two halves of the treble side together.
I'd have to be pretty certain that there was no other way of separating the treble side before cutting the bellows off.

Your reed plates will probably be nailed onto the leather gaskets but may be screwed.
This is quite normal and is the method I use when building accordions.

Lucky you, no wax!
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

KWIMER

  • Member
  • *
  • Offline Offline
  • Posts: 12
Re: leathers
« Reply #4 on: November 08, 2008, 09:48:43 PM »

It is glue.  I can see beads of glue where it was pressed out between the bellows and the treble side.

I thought I would use a dremel, very thin blade.  Can I use a regular cork gasket when I reassemble?

Thanks again, you don't know how happy I am to have found this site.  I have an old 4 row that is in excellent condition, and I'v had this old one around for years.   Glad my wife didn't get rid of it.

Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal