Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 2 [3]   Go Down

Author Topic: pokerwork spring  (Read 15255 times)

0 Members and 1 Guest are viewing this topic.

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: pokerwork spring
« Reply #40 on: November 17, 2011, 09:19:05 AM »

Anyone know of pictures or video in addition to Loffet's excellent pictorial walk-thru?

Sadly no picture/video but it is reasonably easy:

  • Remove the treble end from the bellows (pull the 4 pins and ease the end off)
  • Remove the grill (twist the loopy things and off it will pop)
  • Locate two screws inside the treble end that secure the keyboard and remove them
  • Wiggle the keyboard off the keys (can be a bit fiddly)
  • Unhook all the springs from the arms to take tension off the treble mech
  • Remove the three/four small screws holding the treble mech in place
  • Find a piece of board and screw the mech to it (this makes the next steps a lot easier)
  • Grasp the axle with a pair of pliers and rotate/pull to ease it out
  • As the axle withdraws collect the arms and springs and keep them in order
  • When you get to broken spring replace it
  • Reassembly is the reverse of the above
  • Replacing the small screws is a pain but I use a little reed wax to stick them to my screwdriver which makes location them a lot easier

Have fun  ;D

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: pokerwork spring
« Reply #41 on: November 17, 2011, 09:27:10 AM »

Found some photos, first shows the treble mech of a 1 row pokerwork ready to be screwed to the board and the second the same mech but with the detail of the disengaged springs

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: pokerwork spring
« Reply #42 on: November 17, 2011, 09:44:41 AM »

You can save yourself a lot of fiddly work if at this stage:


  • As the axle withdraws collect the arms and springs and keep them in order

you thread in a second piece of stiff wire to hold all the springs and levers in place.

If you do use Lester's method you should note that there are two different types of spring.   The outside row springs are made of wire 0.55mm diameter, inside row 0.50mm.   Make sure they go back on the correct row or you will fella differnt spring pressure between the rows.   This applies to the new spring too, make sure it is the correct one for the row.

Just noticed that all this is duplicating what was said on the previous page of this thread.  :|bl
« Last Edit: November 17, 2011, 09:47:33 AM by Theo »
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

docEdock

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
  • Hohners, Gaillards, Castagnaris
    • LoafingAboard
Re: pokerwork spring
« Reply #43 on: November 18, 2011, 11:50:38 AM »

Thanks for the information and pictures, which allowed me to replace the broken spring without any mishaps.

I found that the wire rod hard to withdraw and ended up grasping it with a spare drill chuck, which served as a handle and allowed rotating the rod when extracting and inserting. A spare strand of wire from an Ethernet cable worked as a keeper for the springs and levers as I withdrew the rod. A stiffer keeper would have been better. Next time I'll make a keeper of rod and insert it into a wooden dowel to give it a handle.
Logged
How difficult can it be?
http://loafingaboard.blogspot.com/
Pages: 1 2 [3]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal