Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 2 3 [4] 5 6   Go Down

Author Topic: Melodeon construction -- some more radical thoughts...  (Read 34574 times)

0 Members and 1 Guest are viewing this topic.

Quebecois

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1206
  • Accordez-vous donc, c'est si beau, l'accordéon!
Re: Melodeon construction -- some more radical thoughts...
« Reply #60 on: December 19, 2008, 04:34:36 PM »

It's always useful having a map to tell you where to go instead of blundering around in the dark...
Ian
Inspiration is enlightenment! Maybe you should seek some...
Logged
Hohner Morgane D/G, pre-Erica Hohner in C/F and G/C,
Hohner Erica A/D, Roland FR-18

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Melodeon construction -- some more radical thoughts...
« Reply #61 on: December 19, 2008, 04:40:50 PM »

Even without any resonator at all you still get a frequency shift due to the air mass loading -- compare a reed just in a frame to this mounted in the middle of a flat board (no cavities either side). This is the same effect as a speaker in free air (little sound) compared to mounted in an infinite baffle (big flat plate), the resonant frequency drops as the sound output increases due to air loading (change in acoustic impedance). A resonator -- even driven away from resonance -- also changes the acoustic impedance, as do other things nearby due to reflection of sound energy (actually, anything that changes the acoustical or mechanical impedance seen by the reed could cause a small frequency shift).
I really think we're talking at cross-purposes here.  Perhaps it would help if I re-stated my position as follows:
  • The frequency shift is caused by a change in the impedance seen by the reed.
  • A major component of this impedance is due to the reed being coupled to a cavity, inside the reedblock in most instruments.
  • This cavity is a Helmholtz resonance, although it is not operating at its resonance frequency in most cases.

Quote
As you say, simulating it would make a very nice PhD for someone -- but I do suspect that a couple of years solid work and a *lot* of computing time (see below) are needed, which is not something than any of us (or an instrument maker) is likely to be able to spare.
Well, the joy of long computing jobs is that one can do other things while they're running,  and it's far from uncommon for Musical Acoustics PhDs to be done part-time.  But if anyone were to try this they'd have to be doing it because they really wanted to, rather than any dramatic increase in commercial gain, fame, sex appeal, etc...

Quote
The simulations you referenced are (I think -- correct me if I'm wrong) a pseudo-steady-state type of analysis, similar to harmonic balance simulations in RF circuits, which shows the settled state of the system -- we do the same kind of analysis for IC design, and this is typically 100x faster than a transient analysis which is what you'd need to simulate the start-up behaviour. Add on the need to analyse say 10 different reeds across the pitch range and you're looking at 1000x more computation; now assume 10 design iterations to do your tweaking/improvement and you have 10000x more computation -- which is why I guessed we might be 10 years away from this being feasible in a reasonable time.
Yes they were steady state (though not directly computational) and yes the transient solution will take longer, but in flow acoustics time-domain methods are creeping up on frequency domain ones and I'd conjecture that the factor wouldn't be as big as the one you experience in your line.  And my thinking was that seeing the results from just one simulation of a typical reed might tell us enough about what the air and the reed do to each other to give us some ideas about changing cavity shapes that could be tested directly on the analogue computer we call a melodeon.

Quote
Your idea of flat-mounted cavityless reeds with very big pallet holes will come close in sound to the "reeds-out" idea, the concept is similar and it might be easier to try out quickly to see what it sounds like (in case we hate the result!).
In that case I fear I've misunderstood your 'reeds-out' idea; are no reedblocks involved? 


Yes, I think we're agreeing on the impedance issue, we're just looking at it from different directions.

The "reeds-out" idea is that you can have relatively conventional reedblocks but facing outwards; then the reed cavities/pallet holes/pallets are in the sound path between the reeds and the inside of the bellows instead of between the reeds and our ears, so we hear the "direct" reed sound and the bellows hear the "filtered" reed sound.

This way you can have as many reeds as in a conventional instrument -- actually, probably more because the blocks don't have to fit down the hole in the bellows, so you can use the whole area of the end like in a Preciosa.

Ian
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Melodeon construction -- some more radical thoughts...
« Reply #62 on: December 19, 2008, 04:49:06 PM »

It's always useful having a map to tell you where to go instead of blundering around in the dark...
Ian
Inspiration is enlightenment! Maybe you should seek some...


I get plenty of inspiration anyway thanks, both at home (playing/thinking about melodeons and PA design) and at work (IC design and consultancy) -- if I didn't get inspiration I guess I wouldn't have such a big pile of patents, many of which fell into the "that's not possible" category until we showed that it was :-)

Often the inspiration proves correct, and it works, and everyone's happy. Other times it's wrong and we spend a lot of time and effort going down a blind alley :-(

I reckon it's better to have a pointer in the right direction if possible than not, so if you want to improve something you at least have some idea of what might work or not. Other people obviously don't...

Ian
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

Quebecois

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1206
  • Accordez-vous donc, c'est si beau, l'accordéon!
Re: Melodeon construction -- some more radical thoughts...
« Reply #63 on: December 19, 2008, 05:13:08 PM »

It's refreshing to see that some people actually own the truth with such degree of humility and confidence!
« Last Edit: December 19, 2008, 05:15:30 PM by québécois »
Logged
Hohner Morgane D/G, pre-Erica Hohner in C/F and G/C,
Hohner Erica A/D, Roland FR-18

Waltham

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 198
Re: Melodeon construction -- some more radical thoughts...
« Reply #64 on: December 19, 2008, 06:43:29 PM »

The "reeds-out" idea is that you can have relatively conventional reedblocks but facing outwards; then the reed cavities/pallet holes/pallets are in the sound path between the reeds and the inside of the bellows instead of between the reeds and our ears, so we hear the "direct" reed sound and the bellows hear the "filtered" reed sound.
In that case I don't think the 'no cavity' and the 'reeds out' configuration would behave the same, because the 'reeds out' box will still have its reeds coupled to cavities.  I should make it clear I'm not suggesting that a 'no cavity' box should sound good, just that it might shed some light on the role played by the cavities, so I'm not too bothered by the practicalities of making a multirow version.  My feeling is that they must make an appreciable difference or Hohner wouldn't have bothered putting them on Pokerwork 1-rows.

I should also clarify that for my shutter and conical plug suggestions I wouldn't expect them to sound like better versions of existing instruments.  Instead there would (might) be a gradual change in sound as the button is depressed which might be interestingly expressive or might be awful.  Or might not work at all.

The immediate difficulty I see in making a 'reeds-out' box is having a moving rod going from each external button to its corresponding internal pallet without compromising the airtightness.  Maybe you give each pallet a servo and make a wireless link?
Logged

Mike Higgins

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 338
    • Strolling to Italy
Re: Melodeon construction -- some more radical thoughts...
« Reply #65 on: December 19, 2008, 07:13:24 PM »

Chaps, go on, tell me, you know you want to, how much of this thread is total tosh?
Logged
Mike from Ponte Caffaro

Matthew B

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 894
Re: Melodeon construction -- some more radical thoughts...
« Reply #66 on: December 19, 2008, 08:01:36 PM »

shutter and conical plug suggestion

. . . hmmmmmm . . .
Logged
Charter Member Presumpscot and Fore River Accordion Club

Falseknight

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 449
    • False Knight
Re: Melodeon construction -- some more radical thoughts...
« Reply #67 on: December 19, 2008, 08:14:35 PM »

Considering we are talking about glorified gob irons...
Logged

stillicidia

  • Member
  • *
  • Offline Offline
  • Posts: 26
Re: Melodeon construction -- some more radical thoughts...
« Reply #68 on: December 19, 2008, 09:53:24 PM »

Considering we are talking about glorified gob irons...
Ah! a truly out of the bellows free reed instrument ::) - do they sound better I wonder?
R. ;)
Logged
Dyslexic fingers and deaf as a post!
member of accordions anonymous - I admit it I am an accordion addict!
it all started with just one! just a little one! then another, and another...

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Melodeon construction -- some more radical thoughts...
« Reply #69 on: December 19, 2008, 11:30:16 PM »

Chaps, go on, tell me, you know you want to, how much of this thread is total tosh?

If you're not interested don't read it.

And if a "better" melodeon ever emerges as a consequence (likely or not), don't buy it.

Then everyone will be happy :-)

Ian
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

risto

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 317
Re: Melodeon construction -- some more radical thoughts...
« Reply #70 on: December 20, 2008, 08:48:40 AM »


...
And if a "better" melodeon ever emerges as a consequence (likely or not), don't buy it.
...
Ian

Because of this discussion?  HO-HO. I always love a good joke.
Logged
Paolo Soprani 5-row, Roland FR1B-digital CBA button accordion. Guitar, 5-string OT banjo, mandolin, piano...
My one man band recording: https://apari.fi/Bonaparte_Crossing_The_Rhine_Risto.mp3

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Melodeon construction -- some more radical thoughts...
« Reply #71 on: December 20, 2008, 09:32:03 AM »


...
And if a "better" melodeon ever emerges as a consequence (likely or not), don't buy it.
...
Ian

Because of this discussion?  HO-HO. I always love a good joke.

You just never know -- there's been no significant change in melodeon design and construction for a very long time (except Stormy Hyde trying out some different -- but still wooden -- materials), everyone's been pretty much doing it the "standard" way with a few small tweaks.

If this discussion prompts somebody into trying something new and different that works then it will have been useful -- if not, it'll disappear into the worldwide morass like many other similar "what-if" discussions, I'm under no illusions here :-)

Either way, like I said -- if you're not interested, don't read it. Other people may have different interests to you and want to discuss different things (e.g.  melodeon acoustics in great technical detail), that's what a forum is for.

And it's *so* much easier to criticise any suggestions that things could be done differently than to think and come up with new ideas about how this might be done -- so please continue to take the easy way out if that's what you want to do :-)

Ian
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

Falseknight

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 449
    • False Knight
Re: Melodeon construction -- some more radical thoughts...
« Reply #72 on: December 20, 2008, 11:21:30 AM »

Not completely off topic, but what actually determines the dynamic range of a free reed instrument?

OBVIOUSLY it is  volume of airflow through the reed, but, from the lowest flow, where the reed starts to speak to point where either the reed flaps or volume ceases to increase what controls the range?

Hamonicas are (thankfully) fairly quiet instruments, yet small melodeons are not!.
Logged

TomB-R

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 598
Re: Melodeon construction -- some more radical thoughts...
« Reply #73 on: December 20, 2008, 11:58:37 AM »


...
And if a "better" melodeon ever emerges as a consequence (likely or not), don't buy it.
...
Ian

Because of this discussion?  HO-HO. I always love a good joke.

Not the most positive post in the world Risto, old bean.

Why do scientists and people in all sorts of technical fields travel to conferences to hear what people have been doing, meet, chat etc? Surely it's partly to spark new ideas and directions that wouldn't have happened without that sharing.  Given that an international Melodeon Construction Symposium is unlikely to happen anytime soon, why not achieve part of the process here?
Tom
Logged

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Melodeon construction -- some more radical thoughts...
« Reply #74 on: December 20, 2008, 12:57:27 PM »

Not completely off topic, but what actually determines the dynamic range of a free reed instrument?

OBVIOUSLY it is  volume of airflow through the reed, but, from the lowest flow, where the reed starts to speak to point where either the reed flaps or volume ceases to increase what controls the range?

Hamonicas are (thankfully) fairly quiet instruments, yet small melodeons are not!.

The few papers on free-reed instruments show that the reed amplitude is almost independent of air pressure, once the reed starts to vibrate it settles down at a relatively fixed movement, the volume then depends on the air pressure which determines how much air flows though the reed. If you think that the reed pretty much completely shuts off the air flow when it's within of the frame (so it lets two pulses of air through per cycle as it swings above and below the frame), this means that volume -- up to a point -- is proportional to air flow, which is proportional to air pressure.

So one thing that will limit the maximum volume is how much air you can push through the reed; since the air has to get past the reed frame and the sound holes and the pallets (all of which cause pressure drops) there will come a point where it's difficult to force more air through what is after all a relatively small hole.

Another thing is that if you play really hard the reed amplitude does eventually increase, and this is often accompanied by a drop in pitch -- the "waaah" sound of a reed in pain on a thrashed melodeon. Once this happens the reed spends less time in the frame (closed) and more time above and below the frame (open) so more air flows through without being chopped up by the reed, and the volume flattens out -- playing even harder pushes more air through but without making much more sound, the reed just spends more time open and less time closed.

The way to get more volume is to get more airflow before this happens, and make the reed less prone to being overdriven; so bigger area (longer and/or wider) reeds which are stiffer will give higher maximum volume. Anything that allows more air through and more sound out (bigger pallets and sound holes) will also increase volume if the reed doesn't limit the volume first.

Of course bigger stiffer reeds take more air to make them speak so are not so good at playing quietly; my guess is that the useful quiet-to-loud dynamic range is roughly constant (because of scaling factors), if you want more maximum volume you'll lose out on minimum volume.

Ian
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

Martin J

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 902
  • Poole, Dorset
Re: Melodeon construction -- some more radical thoughts...
« Reply #75 on: December 20, 2008, 01:06:18 PM »

This thread should get a prize for being one of the fastest moving on record.

Was it only yesterday Waltham asked how to tune reeds reasonably accurately out of the box.  A concertina tuner told me to measure every note before removal and re measure on the tuning table.  Note the difference and apply the difference to your new tuning.  Once the reed is back in place it is right or exceptionally close.

Small chambers/large chambers ?  Elsewhere on this forum I have read that if the chamber is too small then the reed won't speak, so size is important.  A Q' for the accordionists.  I noticed on a friends very expensive chest organ that he had a stop which gave a very sweet tone.  He told me the stop redirected the air through a much longer route than would be the norm.  Sorry I don't know the name of this stop - accordionists help please and can you confirm the changed sound (and my understanding of it)
Logged
Castagnari, Weltmeister, Giustozzi, Streb, too many Hohners.  No Strings Attached ceilidh band

finnhorse

  • Guest
Re: Melodeon construction -- some more radical thoughts...
« Reply #76 on: December 20, 2008, 01:25:46 PM »

If one were to change things like which side of the board the reeds are on, etc., then we wouldn't really be talking about an accordion as we know it.  I think such an instrument would sound quite foreign, very loud, and rather harsh.  I don't think that's why any of us got into playing these things. 

I think the mainstays and basic features of accordion design have remained static for so long because the general concept of the instrument leaves little to be improved.  For the most part, accordion design hasn't undergone any truly dramatic changes since 1945 or earlier.  I'm talking about the way the thing works and how it functions, where the parts are and so forth.  Change anything beyond a fiddle or a tinker and you no longer have an accordion.  It's the same way with many other instruments.  Take violins, for instance.  Some of those designs are 300 years old and we're still knocking them off.

We've seen lots of tweaks over the years, and instruments today are much better than 100 years ago.  Changes seem confined to three areas:

1) improved playability
2) tunings/layouts/stops for repertoire flexibility or increased chromatic play
3) improved tone. 

Developments continue right on up to the present day.  Some improvements in the playability department could even be the incidental results of better craftsmanship.    .

Among some of the more obvious or notable recent developments that I can see are:

-  Andre Bouchard's new boxes, nuff said.
-  Saltarelle Bouebe's improved action for consistency in dynamics across rows, and also the configuration favoring the Irish
    player by adding thirds with the stop
-  Peter Hyde's rainbow of experiments with building materials and tonal response
-  Castagnari's scalloped tone chamber
-  the new 34-button boxes from Hohner (it sure took them long enough).
-  homebrew two-tone boxes from the Tex-Mex circuit going mainstream (wish someone would do this with 2 row boxes)
-  the Streb

There are probably a million more, but most of these things are details, making the accordion friendlier to the player and more adaptable.  Some are too clever for mass production.  But I don't think I know of any real "breakthroughs" in accordion design because I'm not sure there are any to be made.

What I would like to see isn't a mutant accordion with reeds staring at me.  It's not increased volume (really -- let's get real we're the loudest bloody thing in the room most of the time).  It's on another level.  Considering the millions (yes, millions) of hopelessly addicted accordion players and enthusiasts all over the world, I'd like to see more consistency in traditional-style assembly line boxes at affordable prices.  I don't understand why quality in quantity just can't happen everywhere, faster.  When BMW introduces a new technology to their fleet, it's five years before GM is offering it as a standard package feature and they're probably one of the worst managed companies on the planet.  Why can't the same be true with accordions?  We'll pay for it.  We're always paying for another accordion, trading up, retooling.  I'd like to see more price point competition in bigger manufacturers.   

... as a concession to myself, there is something that could be done to fix a nagging problem.  To assist the player caught in a rare moment of bellows mismanagement, how about a small can of compressed air for sounding the next note.  It could be mounted underneath the keyboard and activated with a small switch or foot pedal (like a stomp box).  Any player observed using this feature more than once a night would be ostracized from the session, of course.    ;D
Logged

Waltham

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 198
Re: Melodeon construction -- some more radical thoughts...
« Reply #77 on: December 20, 2008, 01:31:55 PM »

Quote
Was it only yesterday Waltham asked how to tune reeds reasonably accurately out of the box
Errr, no, maybe someone else?

Quote
I noticed on a friends very expensive chest organ that he had a stop which gave a very sweet tone.  He told me the stop redirected the air through a much longer route than would be the norm.  Sorry I don't know the name of this stop - accordionists help please and can you confirm the changed sound (and my understanding of it)
The chamber in question is called a cassotto, not often used on melodeons, though Castagnari used to offer it as an option on one of their bigger boxes, and Serenellini do/did one.  Has anyone here tried one?  I gather they add a fair bit of weight, complexity and expense, which may be why us push-pullers tend not to go for them.
Logged

Falseknight

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 449
    • False Knight
Re: Melodeon construction -- some more radical thoughts...
« Reply #78 on: December 20, 2008, 01:52:51 PM »


... as a concession to myself, there is something that could be done to fix a nagging problem.  To assist the player caught in a rare moment of bellows mismanagement, how about a small can of compressed air for sounding the next note.  It could be mounted underneath the keyboard and activated with a small switch or foot pedal (like a stomp box).  Any player observed using this feature more than once a night would be ostracized from the session, of course.    ;D

Not completely what you are suggesting, but I remember Jean Pierre Raal (I think) using bagpipes that were blown by an electric fan when he was playing with the Albion Band in the 80s.
Logged

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Melodeon construction -- some more radical thoughts...
« Reply #79 on: December 20, 2008, 01:58:26 PM »

If one were to change things like which side of the board the reeds are on, etc., then we wouldn't really be talking about an accordion as we know it.  I think such an instrument would sound quite foreign, very loud, and rather harsh.  I don't think that's why any of us got into playing these things. 

I think the mainstays and basic features of accordion design have remained static for so long because the general concept of the instrument leaves little to be improved.  For the most part, accordion design hasn't undergone any truly dramatic changes since 1945 or earlier.  I'm talking about the way the thing works and how it functions, where the parts are and so forth.  Change anything beyond a fiddle or a tinker and you no longer have an accordion.  It's the same way with many other instruments.  Take violins, for instance.  Some of those designs are 300 years old and we're still knocking them off.

We've seen lots of tweaks over the years, and instruments today are much better than 100 years ago.  Changes seem confined to three areas:

1) improved playability
2) tunings/layouts/stops for repertoire flexibility or increased chromatic play
3) improved tone. 

Developments continue right on up to the present day.  Some improvements in the playability department could even be the incidental results of better craftsmanship.    .

Among some of the more obvious or notable recent developments that I can see are:

-  Andre Bouchard's new boxes, nuff said.
-  Saltarelle Bouebe's improved action for consistency in dynamics across rows, and also the configuration favoring the Irish
    player by adding thirds with the stop
-  Peter Hyde's rainbow of experiments with building materials and tonal response
-  Castagnari's scalloped tone chamber
-  the new 34-button boxes from Hohner (it sure took them long enough).
-  homebrew two-tone boxes from the Tex-Mex circuit going mainstream (wish someone would do this with 2 row boxes)
-  the Streb

There are probably a million more, but most of these things are details, making the accordion friendlier to the player and more adaptable.  Some are too clever for mass production.  But I don't think I know of any real "breakthroughs" in accordion design because I'm not sure there are any to be made.

What I would like to see isn't a mutant accordion with reeds staring at me.  It's not increased volume (really -- let's get real we're the loudest bloody thing in the room most of the time).  It's on another level.  Considering the millions (yes, millions) of hopelessly addicted accordion players and enthusiasts all over the world, I'd like to see more consistency in traditional-style assembly line boxes at affordable prices.  I don't understand why quality in quantity just can't happen everywhere, faster.  When BMW introduces a new technology to their fleet, it's five years before GM is offering it as a standard package feature and they're probably one of the worst managed companies on the planet.  Why can't the same be true with accordions?  We'll pay for it.  We're always paying for another accordion, trading up, retooling.  I'd like to see more price point competition in bigger manufacturers.   

... as a concession to myself, there is something that could be done to fix a nagging problem.  To assist the player caught in a rare moment of bellows mismanagement, how about a small can of compressed air for sounding the next note.  It could be mounted underneath the keyboard and activated with a small switch or foot pedal (like a stomp box).  Any player observed using this feature more than once a night would be ostracized from the session, of course.    ;D

I agree that there have been a lot of small detail improvements, but I'm not sure I agree that a "reeds-out" instrument wouldn't be a melodeon (or an accordeon, bit I was specifically talking about melodeons).

Given that the term encompasses everything from single-reed to four-reed, one-row to four-row, tiny sub-kg boxes like the Preciosa to massive 8kg ones like the Helicons, steel and brass reeds mounted flat or on blocks, separate aluminium and single zinc reed plates, wood and plastic finishes, wooden and metal action, reeds held in with wax/leather/nails, instruments with and without stops and cassotto chambers -- the difference between a two-row two-reed 8-bass with the reeds on the outside or the inside seems small in comparison.

As was said, all these "big" structural changes that I've mentioned happened 50 years ago or more; one possibility is that only small improvements are possible any more, another is that most people have stopped looking for or trying such changes and are just content to "tweak" existing designs. Like I said though, just because you're happy with the result doesn't mean it can't be improved, and big improvements in anything usually come from radical changes not small ones (transverse engine and FWD with the Mini).

If the "reeds-out" idea doesn't sound too horribly bright (which is possible, as I said several times) then it will almost certainly be louder and brighter sounding than current boxes. So you can either keep the reeds the same and gain volume and punch at the loud end -- useful for playing outdoors unamplified for morris without knackering your arm, the bellow, or the reeds -- or you could use smaller reeds and gain at the quiet end, these would then use less air and speak more quickly at low volumes. Then you could have a smaller lighter box which was easier to play but delivered the same maximum amount of sound with less air and was better to play quietly.

There's one other big advantage which I'm sure Theo would appreciate -- you could do all final reed tuning on the instrument with the reed blocks in place (if you used something like Dirk's Accordion Tuner which can show the tuning of several reeds at the same time):

http://www.dirksprojects.nl/index.php?Lan=english&Page=Tuner/accordion_tuner_22.php

As for "What I would like to see isn't a mutant accordion with reeds staring at me." -- well, put them under a cover like they are now then you wouldn't see them, this would be needed anyway to keep dirt out. Compared to "mutant melodeons with the levers and pallets staring at me" like four-stop one-rows I think the result would be quite aesthetically pleasing :-)

Ian
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses
Pages: 1 2 3 [4] 5 6   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal