Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Rebuilding a keyboard of a 100yr old box  (Read 2021 times)

0 Members and 1 Guest are viewing this topic.

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Rebuilding a keyboard of a 100yr old box
« on: April 02, 2013, 07:32:34 AM »

Though folks might like to see how I did this.

I was asked to restore a old Empress button box.

The original buttons were all gone, and had been replaced with thumb tacks and bits of dowel.

I softened the keys of a old piano accordion (they were ivory patterned celluloid) in acetone vapor for about an hr. A hole punch just over the size wanted gave me a good pile of discs in a few min. I made a jig and cut a hardwood dowel to 1/4 lengths. The discs were glued to the ends of the dowels (gap filling superglue was used).
 After the glue had set each dowel was chucked in a Unimat lathe and turned to size , and the bevel on top was added. They also got a lite sanding at this time.
 
I used 1500 grit sand paper to smooth things a bit then held the button by the dowel and rubbed it briskly against a thick rag on the table that had auto paint scratch remover worked into it. All shiny now.

The rod was broken off in the keyboard, and some of the keys were sticky. The rod was set into a slot and backed with bits of glued in wood. The dremel with a router tip got the bits of wood out and the rod came out ok then.
 
Key ends where the old buttons were were cleaned off and the arms drilled for a slightly larger rod. a piece of brass with sand paper glued on one side was used to widen the slot for the new rod.
 
Arms were reinstalled with new rod, and new bits of wood sanded to size were glued in the slot behind it. The rod could now be drawn out from the end as intended.

 The new buttons were glued in place (height was checked beforehand to make sure the arm would be removable) placing them off center toward the valves keeps the clearance correct when the button is pressed down.
 The buttons are yellowed ,as they are cut from old celluloid so the match the accordion nicely.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

Ebor_fiddler

  • Chris
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2340
  • Hohner 1040 C One-Row, Sandpiper D/G, Liliput C/F
    • Ebor Morris
Re: Rebuilding a keyboard of a 100yr old box
« Reply #1 on: April 02, 2013, 12:38:10 PM »

Neat!  :||:
Logged
I'm a Yorkie!
My other melodeon's a fiddle, but one of my Hohners has six strings! I also play a very red Hawkins Bazaar in C and a generic Klingenthaler spoon bass in F.!! My other pets (played) are gobirons - Hohner Marine Band in C, Hohner Tremolo in D and a Chinese Thingy Tremolo in G.

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Rebuilding a keyboard of a 100yr old box
« Reply #2 on: April 02, 2013, 10:13:02 PM »

Nice job. Ingenious.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Rebuilding a keyboard of a 100yr old box
« Reply #3 on: April 11, 2013, 07:03:17 AM »

Finally done. It was mostly a lot of little things.

It had zinc single plates with brass reeds, but the jig I came up with last year makes tuning these as easy as regular reeds if not a bit easier, as long as there are no bad reeds.
 The thing is surprisingly loud and is well balanced tonaly. the valves in the bass were of the cajun style and had to be rebuilt, and I had to rework the air valve as it looked like it had never sealed quite right.

Here is a pic of the finished box
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

Etienne

  • Student in push-pull things
  • Regular debater
  • ***
  • Offline Offline
  • Posts: 186
    • ça s'pousse et ça s'tire
Re: Rebuilding a keyboard of a 100yr old box
« Reply #4 on: April 11, 2013, 09:08:39 AM »

Nice box, i like the simplicity of the square marquetry.
Logged
Old hohner and old Dedenis
http://pousser-tirer.blogspot.com

Accordion Dave

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 380
Re: Rebuilding a keyboard of a 100yr old box
« Reply #5 on: April 28, 2013, 03:49:53 AM »

I hope that the piano accordion was unplayable.

It would be a shame to canabalise a perfectly fine piano accordion.

I used reeds from a piano accordion that had been thrown out an attic window to repair one of my melodeons.

Most of the piano keys were broken beyond repair.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal