Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Muffled inner row  (Read 5040 times)

0 Members and 1 Guest are viewing this topic.

Ted

  • Good talker
  • **
  • Offline Offline
  • Posts: 62
Muffled inner row
« on: September 23, 2013, 08:24:55 PM »

I know there are some folks here who have had some specific experience with muffled inner rows. Just got back a Hohner Trichord after having LMM tipo a mano reeds (BCD) and new key tops installed. I was surprised at the difference in sound and response between the inner row (muffled & sluggish) and the 2 outer rows. As you know these things have 4 1/2 reed blocks and I was told that the main problem is with the metal bar that is close to and in front of the inner row pallets. It is quite wide and the edges are bent inward further obstructing the path of the sound? Does this make sense? And have you heard of modifications to this bar helping to correct the muffled problem?

I just checked the 1 1/2  'D' blocks for leaks with a shim and they seem very tight. Another part of the problem may be that the pallets on the inner row may not open as much as the outer row pallets. I have no idea how to improve this without upsetting the key top adjustments except maybe to tilt the sound board slightly = major surgery(?).
Logged

pgroff

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1827
Re: Muffled inner row
« Reply #1 on: September 23, 2013, 09:01:52 PM »

Hi Ted,

Does it sound better and play more freely with the grille off?  In that case you might want to switch the kind of grillecloth you use (or even go without grillecloth, as I often do -- the influence of years playing a Jeffries concertina), modify the grille itself, or play with the grille off altogether.  You wouldn't be the first to take those steps.

If when testing the box with the grille off altogether you still notice a muffled inner row, I personally would next check the job that was done on the valves for the new reeds.  I recently re-worked a LMMM Hohner box that had just had a total overhaul, but the tech had glued down the new plastic valves for too much of their length to suit the response I wanted.  When the valves were free to open further (still lying flat at rest), the response improved a lot.

If those valves all look fine I would next look at at pallet lift.  A lot of players seem to ask for minimal key travel (low buttons, and/or high padding below them).  But I personally often prefer more key travel (higher buttons and/or less padding beneath) if that gives me more pallet lift.  There can be a trade-off between reed response and keyboard feel, so you may want to play with the key travel to see if you can find a different compromise that suits you better.

It may be that the new reeds want bigger airways (especially the L rank if this was a conversion from MMM to LMM).  You probably wouldn't get into a modification in this case, but I have seen boxes where the holes in the soundboard and/or in the soles of the reedblocks have been enlarged, tapered, or reworked from round to square to help airflow.

I'm sure the pro accordion techs here will have some other good suggestions for you!

A final thought -- sometimes when these differences are just a matter of timbre (tone quality), not of air flow, you might be able to learn to put up with them if you are not close-miking the accordion.  I've often seen instruments in which the player hears great differences in timbre across the instrument that are not so obvious to a listener a few feet away.  This can be really noticeable in concertinas but also some accordions.

PG
« Last Edit: September 23, 2013, 09:08:01 PM by pgroff »
Logged

Ted

  • Good talker
  • **
  • Offline Offline
  • Posts: 62
Re: Muffled inner row
« Reply #2 on: September 24, 2013, 04:20:38 AM »

Hi Paul and thanks for all the ideas! Most of what you mentioned have been checked. The grille on or off doesn't seem to matter. I will check the pallet lift. The attached photo below shows the metal bar across the lower pallets that I mentioned. I would really like some advice regarding that bar.
Logged

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Muffled inner row
« Reply #3 on: September 24, 2013, 07:14:01 AM »

Corona series 3 voicers are always a bit more muffled on the inner row, they`re no where near as bad as the 9 coupler 1980s Paolo soprani 2 row 4 voicers which sound as lively as a shand morino on the outer row but sound like a Piano accordion with socks under the grille on the inner - there`s nothing you can do about that either. even my 2 coupler 4 voice baffetti Irish is more muffled on the inner row than any Hohner Corona-III series box I`ve heard. My thought is that in your case, The L reeds should make the muffling less obvious as they contain less high frequencies (which muffle the worst) . the Club Morino has its L reeds in a kind of cassotto which is designed to muffle and even that hasn`t a drastic affect .

From what I can gather It`s down to the basic design of where the reedblocks are in the box & how far the pallets move more than rails getting in the way . I removed the grille and fingerboard base from that Paolo 9 coupler, didn`t make a difference, even moved the massive coupler bar out of the way and that didn`t make a diff either, still sounded like socks on the inner row. I have a Vallenato (basically a painted Corona-III) and although the inner row is a bit more muffled, I`ve got used to it ..
Logged
Q: How do you cure MAD?
A: Buy more Boxes

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Muffled inner row
« Reply #4 on: September 24, 2013, 07:49:30 AM »

Just look at the picture and you can see the reason: the pallets for the inner row are visibly hidden behind the lower edge of the keyboard and mechanism.  Sound will be diffused by passing through all those bits and pieces.  You can perhaps lessen the problem slightly  with the tweaks that Pgroff suggests, but I don't think you can cure it.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11154
  • Wirral UK
    • Chris Ryall
Re: Muffled inner row
« Reply #5 on: September 24, 2013, 10:04:58 AM »

My van der Aa came last year with inner row pallets hinged away from the keyboard! The keys work a different lever and there is a cantilever system linked with a little plastic loop to ensure all pallets move roughly the same distance.

So, genuine issue, you can devise technological solutions, and it's complicated!

 video http://youtu.be/4uZmT3RdISI
Logged
  _       _    _      _ 

Microbot

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 345
Re: Muffled inner row
« Reply #6 on: September 24, 2013, 12:43:41 PM »

Hi Chris!

If you look back at the photo of the Trichord action, you'll see that this, too (as with Coronas) has the remote-hinged, 'cantilever' system for the lowest set of pallets, to provide a more even 'lift' to the pallets. Looking at the video of your Van der Aa, the significant difference with the Trichord is indeed the presence of the metal bar and the very low positioning of the pallets, due to there being so many reedblocks!

It is a problem with many big hohner boxes!

cheers

Mike
« Last Edit: September 24, 2013, 12:45:17 PM by Microbot »
Logged

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11154
  • Wirral UK
    • Chris Ryall
Re: Muffled inner row
« Reply #7 on: September 24, 2013, 12:58:40 PM »

Oh, yes, so it does. That was a daft "miss" as I did open the photo before my post.
Logged
  _       _    _      _ 

pgroff

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1827
Re: Muffled inner row
« Reply #8 on: September 24, 2013, 01:05:33 PM »

Hi Ted and all,

OK . . . How about ventilating the plastic keyboard plate with some holes/fretwork?  If that might weaken the part too much, maybe a customized aluminum one could be made that is fretworked between the inner row of buttons and the grille.

In fact, you could just cut away a slot in the top of the keyboard plate.  The bottom section of the metal grille could also be cut away.  Compare the shape of the top of the keyboard for the Hohner 114 4-stop boxes.

Then, the back of the wooden keyboard housing could also be ventilated with holes or fretwork.  Paolo Soprani Irish-style boxes changed from having an unventilated back of the keyboard to a ventilated back, and I think a fair amount of sound comes out of the ventilated ones.  Maybe not if you use two shoulder straps and hold the box tight to the chest . . .

PG
Logged

Malcolm Clapp

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1119
  • Loving my Hohner-reeded wet MMM CastaTommy
Re: Muffled inner row
« Reply #9 on: September 24, 2013, 01:17:29 PM »

Not that it has any bearing on the problem, but B/C/D seems a slightly unusual key combination. Care to enlighten us, Ted?

Presumably, the Trichord was originally in B/C/C#. Was the problem not apparent whilst in that configuration?

Logged
Tuner/repairer, now retired.

Skipy

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 171
Re: Muffled inner row
« Reply #10 on: September 24, 2013, 06:53:08 PM »

Ted,

If it's any consolation, my b/c/c# Trichord also appears, to me, to be slightly muffled on the c# row when I'm playing!

However, despite me using all three rows regularly and on a recent trip to Ireland, I spent a few evenings mainly on the c# (inner) row and at no time, have any other musicians or punters listening, whether they are sat next to me or further away, ever commented on this!

So, I just assume that it is more noticeable when you are playing, than if you are listening?

Other players have played my box whilst I've been listening and I can't say that I notice the muffling. I just think the box sounds even nicer when you're listening to it at a distance than when you're listening to it whilst playing it  :D

Have you tried listening to it whilst someone else plays it?


Logged
Saltarelle Solstice 12 B/C/C#, Hohner Trichord III B/C/C#. 

I can't imagine life without my melodeons!

KLR

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 640
Re: Muffled inner row
« Reply #11 on: September 24, 2013, 07:25:27 PM »

Morinos only used 2 rows of pallets, even with 5 voices.  My Club is balanced perfectly, even my Casta Rik ADG fades a bit on the G row, and its keyboard is effectively hollowed out above that set of buttons.  The whole 3 rows of pallets thing seems to be just a bad way to go, which has unfortunately become the norm, like the "tremolo" (actually vibrato) arm on Fender electric guitars, which are just what you need to put the thing out of tune...

Perhaps someone has compared volume output of L reeds in cassotto vs without; as I understand it they take out higher partials and improve response, haven't read anything about their impact on gross decibels but a big piano accordion is NOT quiet!  And their owners are more than happy with the results, even going for double cassotto and multiple tone chambers etc. 

A friend has a D/C# Boxeen, he drilled a multitude of holes in the coupler box to bring up the inner row, no big challenge as he's a machinist.  I don't know if he got that idea from Jim Coogan, or from  my friend's teacher (used to play with Cooley and Keegan), but as I recall it didn't really do the trick either.

On the subject of conversions, I just converted my Trichord to C/C#/D, so will be spending lots of time on the inner row, which is a titch quieter, but I like the keyboard layout best this way, I never took a shine to B/C.  Mine's only MM so the imbalance between rows isn't such a deal breaker, I feel; with an L voice the muting becomes more apparent, or so it seems.  As Skipy suggests maybe a lot of this is psychological. 
Logged

Microbot

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 345
Re: Muffled inner row
« Reply #12 on: September 24, 2013, 08:17:22 PM »

Hi Ted, Paul and all,

Paul offers a range of very crafty solutions - I think there is no single 'magic bullet', but you have to undertake a range of such measures, each of which will contribute...

Another point I'd throw in - be careful if you resurface the pallets - new pallet surfaces absorb sound as it exits the soundholes, and can hugely change the tone of a box. So ... if you resurface the pallets on a box with 'inner-box muffling' issues - I use just chamois on the inner row - not Persian+felt - which I use on the outer rows (where this is more important due to the need to reduce 'impact-clatter').

The fact that the Morino requires only two rows of pallets for a 5-voice 3 row box tells you that, ultimately, the solution lies in the design stage ... narrower reedblocks, reeds packed more closely along the reedblock, complex action ... Paul Groff kindly alerted me to a box (which I didn't go for, but Thanks Paul!) which is a 3-voice, 3-row instrument - but notice there are only two rows of pallets... see the photo below ...

It may perhaps be true that the disparity between 'muffled-inner' row and other rows may be more apparent to the assembled listneners than the player. But - hey - as a player I am ALSO a listnener. I want to hear a good sound and the notion that the audience doesn't hear what I hear is not a comforting message!

Good luck Ted and Paul - many thanks for your p.m.!

Mike
« Last Edit: September 24, 2013, 08:26:40 PM by Microbot »
Logged

Adam-T

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1789
  • Hohner Corso
Re: Muffled inner row
« Reply #13 on: September 24, 2013, 08:47:19 PM »

Morinos only used 2 rows of pallets, even with 5 voices. 

Err, Kinda - in that all three rows are covered by the two rows of pallets hence the consistency . where the Morinos got clever was by putting the bassoon reeds on a separate set of pallets behind the fingerboard (The Shand was the first) . the 5 Voice club also has one M reed rank in there as well as you can hear if you select just a single voice of M (it`s muffly but the same on all three rows) .
Logged
Q: How do you cure MAD?
A: Buy more Boxes

Stiamh

  • Old grey C#/D pest
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3611
    • Packie Manus Byrne
Re: Muffled inner row
« Reply #14 on: September 24, 2013, 09:05:51 PM »

Like the box that Mike showed above, my Serenellini 273 is a 3-row 3-voice box with two rows or sets of pallets, but with cantilever hinges (if that's what we're calling them now) to open the bottom set.

There are 27 buttons arranged 12-11-4 (C#/D/reversals). There are 14 pallets on the top set and 13 on the bottom set.

A couple of the middle row (D) buttons open pallets on the top set, and making space for four or the bottom set pallets to be opened by the inner half-row of buttons.

You'd expect this arrangement to mean that four of the notes on the D row would sound louder and less muffled than the others, but I've never noticed that they do. The cantilever hinges must be doing their job... (but maybe I'll check carefully this evening)

Ted

  • Good talker
  • **
  • Offline Offline
  • Posts: 62
Re: Muffled inner row
« Reply #15 on: September 26, 2013, 03:42:10 PM »

First of all many thanks for all the ideas and comments - the discussion was very worthwhile!! I'm going to start with 3 areas:
1. I talked with one of my 'surgeons' yesterday and removal of a good chunk of the metal off the bar in front of the pallets seems like it could be done. Due to some scheduling issues it may take a couple of months.
2. modification of the grille I can do myself.
3. Pallet lift is an issue with this box. Currently there are 2 layers of different material on the pallets. Mike suggested use only one thickness chamois, so we might try this and rebalance the position of the key travel. That may provide enough opening.
If all that still results in an unacceptable loss of high freq. on the inside row, then we will look at further opening the grille and keyboard areas.
Malcolm questioned my BCD tuning which I have been using for about 25 years. (This is my 4th BCD box) I learned from a couple of the older Irish players who came over here in the late 40's - early 50's, before the Paddy O'Brien BC style came along. I never bothered to learn the cross fingering BC for playing in D, and actually didn't like it much anyway - you loose the punch and a lot of the bellows emphasis that's in the single row. So I use the D row for D and some A. I use the BC for G, and then have C & F available for song accompaniment, etc. It's very versatile and allows me to carry one box! I have one other 'convert' here in Rochester, John Ryan, who tells me he has found chord patterns using the 3 treble rows that are not available in the 2 row boxes.
Logged

Malcolm Clapp

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1119
  • Loving my Hohner-reeded wet MMM CastaTommy
Re: Muffled inner row
« Reply #16 on: September 27, 2013, 12:29:06 PM »


Malcolm questioned my BCD tuning which I have been using for about 25 years. (This is my 4th BCD box) I learned from a couple of the older Irish players who came over here in the late 40's - early 50's, before the Paddy O'Brien BC style came along. I never bothered to learn the cross fingering BC for playing in D, and actually didn't like it much anyway - you loose the punch and a lot of the bellows emphasis that's in the single row. So I use the D row for D and some A. I use the BC for G, and then have C & F available for song accompaniment, etc. It's very versatile and allows me to carry one box! I have one other 'convert' here in Rochester, John Ryan, who tells me he has found chord patterns using the 3 treble rows that are not available in the 2 row boxes.


Interesting, and makes a lot of sense. Thanks for the explanation.

Good luck with the modifications.
Logged
Tuner/repairer, now retired.

KLR

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 640
Re: Muffled inner row
« Reply #17 on: August 05, 2015, 06:40:14 PM »

BUMP

I revalved the C# row on my Paolo with vinyl on the treble and leather in the bass, to perhaps brighten the sound a titch - I think it helped a little.  I've revalved the C row in just leather.  Haven't gotten to the B but that will just be leather too.

The action on my Trichord is really low and was thinking that I'll make a new keyboard cover with the area around the buttons sunk - thus effectively raising the action.  That might be a way of brightening a box up, too.  My plan is pretty simple, the cover is just a flat plate of plastic, make a new one with the center part a separate plastic piece from the part that the screws go into, and glue this 2nd part on that - thus a kind of -----____________----- profile.  Neat idea, eh?

My repair man suggested cutting away as much pallet material as possible to brighten up a dead row - I guess he's done this with recalcitrant piano accordions at some point.

BCD was the tuning used by musette pioneer Emile Vacher.  They called it "mixte" tuning.  His playing is a bit punchier than the CBA players that followed.  Lots of clips on YouTube if you want to hear him.  Dunno if any players used that layout afterwards.
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Muffled inner row
« Reply #18 on: August 06, 2015, 11:11:26 AM »

If you are sitting a few feet away from someone playing a three row with a muffled inner row, I wonder how obvious it is to the listener - or to put it another way, whether the listener is likely to notice? The player is holding the instrument right against their chest so they are bound to notice any slight differences in volume. Also: the Hohner IIIR particularly suffers from this problem.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Muffled inner row
« Reply #19 on: August 06, 2015, 11:23:55 AM »

The action on my Trichord is really low

That could be something to look at.  If the pallets don't lift far enough the sound may be attenuated.  Just a small increase in pallet lift can make a big difference.   You don't need to make a new keyboard top for this.  A combination of bending the levers so that the buttons sit higher, and/or lowering the felt stops below the buttons is all that is required.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal